Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

  1. Install the front seat side airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps.



2. INSTALL SEAT TRACK ADJUSTING HANDLE


    B256057
  1. Engage the 2 hooks to install the seat track adjusting handle.



3. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY (w/o Lumbar Support)


    B229882
  1. Install the separate type front seatback assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



4. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY (w/ Lumbar Support)


    B229884
  1. Install the separate type front seatback assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



5. INSTALL FRONT SEAT WIRE (w/ Lumbar Support)


    B229881
  1. Engage the 2 clamps and install the front seat wire.

  1. Connect the connector.



6. INSTALL NO. 1 FRONT SEAT CUSHION PROTECTOR


    B229879
  1. Engage the 2 guides and install the No. 1 front seat cushion protector with the screw.



7. INSTALL NO. 2 FRONT SEAT CUSHION PROTECTOR


    B229877
  1. Engage the 2 guides and install the No. 2 front seat cushion protector with the screw.



8. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (w/ Vertical Adjuster)


    B229867
  1. Engage the clip and install the screw.



    B229869
  1. Engage the hook and install the front seat lower cushion shield RH as shown in the illustration.



9. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (w/ Vertical Adjuster)


    B229873
  1. Engage the clip and install the screw.



    B229875
  1. Engage the hook and install the front seat lower cushion shield LH as shown in the illustration.



10. INSTALL RECLINING ADJUSTER INSIDE COVER RH


    B229863
  1. Engage the guide and install the reclining adjuster inside cover RH.



11. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B229861
  1. Engage the guide and install the reclining adjuster inside cover LH.



12. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B229860
  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B229858
  1. Using hog ring pliers, install 5 new hog rings

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



13. INSTALL FRONT SEATBACK COVER WITH PAD


    B229854
  1. Install the front seatback cover bracket with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
    2. Check that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.



    B229856
  1. Engage the 4 claws and install the 2 front seat headrest supports.



    B229852
  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



14. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    B229847
  1. Using hog ring pliers, install 11 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B232926
  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



15. INSTALL FRONT SEAT CUSHION COVER WITH PAD


  1. Engage each hook as shown in the illustration.


    B229839



    B229843
  1. Engage the 2 hooks as shown in the illustration.



    B229837
  1. Using hog ring pliers, install 3 new hog rings

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



  1. for Passenger Side:



      B229825
    1. Engage the guide and install the belt warning occupant detection sensor.



    2. B229823
    3. Engage the 3 clamps.

    4. Connect the connector.



    B229834
  1. Engage the 4 hooks.



  1. w/ Seat Heater System:



      B229832
    1. Engage the clamp.



    2. B229830
    3. Fasten the front seat cushion cover with pad as shown in the illustration.

    4. Connect the connector.



  1. w/ Lumber support:



      B229829
    1. Engage the 4 clamps.



    2. B229827
    3. Engage the 3 clamps and connect the connector.



    B229821
  1. Engage the hook and install the front seat cushion cover with pad.



16. INSTALL FRONT SEAT CUSHION INNER SHIELD


    B229819
  1. Engage the 2 claws and install the front seat cushion inner shield.



17. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    B226478E01
  1. Install the front seat inner belt assembly with the nut.
    Text in Illustration 
    *1
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. Connect each connector.

  1. Engage each clamp.



18. INSTALL LUMBAR SWITCH (w/ Lumbar Support)


    B229818
  1. Install the lumbar switch with the 2 screws.



19. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY


  1. w/ Lumber Support:



      B229817
    1. Disengage the 5 clamps.

    2. Connect the connector.



    B229815
  1. Engage the clip and 2 claws.

  1. Install the front seat cushion shield assembly with the screw.



20. INSTALL VERTICAL ADJUSTING HANDLE (w/ Vertical Adjuster)


    B229813
  1. Install the vertical adjusting handle with the screw.



21. INSTALL RECLINING ADJUSTER RELEASE HANDLE


    B231000
  1. Engage the claw and install the reclining adjuster release handle.