LUMBAR SUPPORT ADJUSTER ASSEMBLY > INSTALLATION |
| 1. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
![]() |
Install the separate type front seatback assembly with the 4 bolts.
| 2. INSTALL FRONT SEAT WIRE |
![]() |
Engage the 2 clamps and install the front seat wire.
Connect the connector.
| 3. INSTALL NO. 1 FRONT SEAT CUSHION PROTECTOR |
![]() |
Engage the 2 guides and install the No. 1 front seat cushion protector with the screw.
| 4. INSTALL NO. 2 FRONT SEAT CUSHION PROTECTOR |
![]() |
Engage the 2 guides and install the No. 2 front seat cushion protector with the screw.
| 5. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH |
![]() |
Engage the clip and install the screw.
![]() |
Engage the hook and install the front seat lower cushion shield RH as shown in the illustration.
| 6. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH |
![]() |
Engage the clip and install the screw.
![]() |
Engage the hook and install the front seat lower cushion shield LH as shown in the illustration.
| 7. INSTALL RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Engage the guide and install the reclining adjuster inside cover RH.
| 8. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Engage the guide and install the reclining adjuster inside cover LH.
| 9. INSTALL FRONT SEATBACK COVER WITH PAD |
![]() |
Install the front seatback cover bracket with the nut.
![]() |
Engage the 4 claws and install the 2 front seat headrest supports.
![]() |
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 3 new hog rings.
| 10. INSTALL FRONT SEAT CUSHION COVER WITH PAD |
Engage each hook as shown in the illustration.

![]() |
Engage the 2 hooks as shown in the illustration.
![]() |
Using hog ring pliers, install 3 new hog rings
for Passenger Side:
![]() |
Engage the guide and install the belt warning occupant detection sensor.
![]() |
Engage the 3 clamps.
Connect the connector.
![]() |
Engage the 4 hooks.
w/ Seat Heater System:
![]() |
Engage the clamp.
![]() |
Fasten the front seat cushion cover with pad as shown in the illustration.
Connect the connector.
w/ Lumber support:
![]() |
Engage the 4 clamps.
![]() |
Engage the 3 clamps and connect the connector.
![]() |
Engage the hook and install the front seat cushion cover with pad.
| 11. INSTALL FRONT SEAT CUSHION INNER SHIELD |
![]() |
Engage the 2 claws and install the front seat cushion inner shield.
| 12. INSTALL FRONT SEAT INNER BELT ASSEMBLY |
![]() |
Install the front seat inner belt assembly with the nut.
| *1 | Protruding Part |
Connect each connector.
Engage each clamp.
| 13. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY |
w/ Lumber Support:
![]() |
Disengage the 5 clamps.
Connect the connector.
![]() |
Engage the clip and 2 claws.
Install the front seat cushion shield assembly with the screw.
| 14. INSTALL VERTICAL ADJUSTING HANDLE |
![]() |
Install the vertical adjusting handle with the screw.
| 15. INSTALL RECLINING ADJUSTER RELEASE HANDLE |
![]() |
Engage the claw and install the reclining adjuster release handle.
| 16. INSTALL FRONT SEAT ASSEMBLY |
Place the front seat assembly in the cabin.
Connect the connectors under the seat.
Temporarily install the front seat assembly with the 4 bolts.
Lift up the seat track adjusting handle and move the seat to the rearmost position.
![]() |
Tighten the 2 bolts on the front side of the seat.
Lift up the seat track adjusting handle and move the seat to the foremost position.
![]() |
Tighten the 2 bolts on the rear side of the seat.
| 17. INSTALL INNER SEAT TRACK COVER |
![]() |
Engage the claw and guide and install the inner seat track cover.
| 18. INSTALL OUTER SEAT TRACK COVER |
![]() |
Engage the 2 claws and install the outer seat track cover.
| 19. INSTALL FRONT SEAT HEADREST ASSEMBLY |
![]() |
Install the front seat headrest assembly as shown in the illustration.
| 20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 21. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 22. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 23. INSTALL REAR NO. 2 FLOOR BOARD |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 24. INSPECT FRONT SEAT ASSEMBLY |
During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.
If the seat adjusters do not lock simultaneously, loosen the seat mounting bolts to adjust the adjuster position.
w/ Seat Heater Seat System:
Check the seat heater operation.
Turn the power switch on (IG).
Push the seat heater switch on.
Wait 5 minutes or more and confirm that the seat surface becomes warm.
| 25. INSPECT SRS WARNING LIGHT |