Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Power Seat)

FRONT SEAT ASSEMBLY (for Power Seat) > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

  1. Install the front seat side airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps.



2. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY


  1. Engage the 4 guides.


    B299248

  1. Install the separate type front seatback spring assembly to the separate type front seat cushion spring assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH


    B302469
  1. Engage the 2 guides to install the front seat cushion edge protector RH to the separate type front seatback spring assembly.

  1. Install the screw.



4. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

HINT:
Use the same procedure described for the LH side.



5. INSTALL FRONT LOWER SEAT CUSHION SHIELD RH


    B302468
  1. Engage the clip to install the front lower seat cushion shield RH to the separate type front seat cushion spring assembly.

  1. Install the screw.



    B302504
  1. Engage the hook as shown in the illustration.



6. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH

HINT:
Use the same procedure described for the LH side.



7. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B312111
  1. Engage the 2 guides to install the reclining adjuster inside cover LH to the separate type front seatback spring assembly.



8. INSTALL FRONT NO. 1 SEAT WIRE


    B302452
  1. Engage the 3 clamps to install the front No. 1 seat wire to the separate type front seatback spring assembly.

  1. Connect the 2 connectors.



9. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B277150E01
  1. Using hog ring pliers, connect the fastening rubber to the separate type front seatback pad with 2 new hog rings.
    Text in Illustration 
    *1
    Fastening Rubber
    *2
    Hog Ring

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B229858
  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 5 new hog rings

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



10. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
  1. Temporarily install the separate type front seatback cover with pad to the front seatback spring sub-assembly.



    B229856
  1. Engage the 4 claws and install the 2 front seat headrest supports.



    B269656E01
  1. Install the separate type front seatback cover bracket with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
    2. Check that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.



    B302451
  1. Engage the 2 hooks.



    B302506E01
  1. Using hog ring pliers, install the fastening rubber to the front seatback spring with 3 new hog rings.
    Text in Illustration 
    *1
    Fastening Rubber

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B299240
  1. Close the 2 fasteners.



    B299236
  1. Push in the lower part of 2 fasteners to the separate type front seatback cover as shown in the illustration.



    B299232
  1. Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B299228
  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



11. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    B229847
  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 11 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B232926
  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



12. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


  1. Engage each hook to install the separate type front seat cushion cover with pad to the front seat cushion spring sub-assembly as shown in the illustration.


    B312113



    B302509
  1. Engage the 2 hooks as shown in the illustration.



    B302511
  1. Engage the fastener to connect the side airbag wire harness.

  1. Connect the connector and engage the clamp to connect the seat heater wire harness.



    B299222
  1. Engage the 3 clamps to connect the seat heater wire harness.



    B299218
  1. Engage the 4 hooks.



    B302433
  1. Connect the rubber band.



13. INSTALL FRONT INNER SEAT CUSHION SHIELD


    B302431
  1. Engage the 5 claws and install the front inner seat cushion shield.



14. INSTALL FRONT SEAT WIRE


    B312307E01
  1. Engage the 3 claws to close the wire harness cover as shown in the illustration.
    Text in Illustration 
    *1
    Clamp
    *2
    Hook

  1. Engage the clamp and hook to install the front seat wire to the front seat cushion shield.



15. INSTALL LUMBAR SWITCH (POWER SEAT SWITCH ASSEMBLY)
  1. Engage the 4 claws to install the lumbar switch (power seat switch assembly).



16. INSTALL FRONT POWER SEAT SWITCH
  1. Install the front power seat switch with the 3 screws.



17. INSTALL RECLINING POWER SEAT SWITCH KNOB


    B302512
  1. Engage the 4 claws to install the reclining power seat switch knob.



18. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    B302513
  1. Engage the 4 claws to install the slide and vertical power seat switch knob.



19. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY


    B299302E01
  1. Connect the 2 connectors.
    Text in Illustration 
    *1
    Clamp
    *2
    Hook

  1. Engage the clamp and hook as shown in the illustration.



    B312114
  1. Engage the guide and 4 claws as shown in the illustration.

  1. Engage the clip to install the front seat cushion shield assembly.



    B299212
  1. Engage the 6 clamps.

  1. Connect the 4 connectors.



20. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD


    B302427
  1. Engage the 2 claws and clip.

  1. Engage the guide to install the front inner No. 1 seat cushion shield to the front seat cushion shield with the screw.



21. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    B221556E01
  1. Install the front seat inner belt assembly with the nut.
    Text in Illustration 
    *1
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. Connect each connector.

  1. Engage each clamp.



22. INSTALL SEAT ADJUSTER COVER CAP


    B269604
  1. Install the seat adjuster cover cap.

    HINT:
    Use the same procedure for the LH side and RH side.