RADIATOR > INSTALLATION |
| 1. INSTALL RADIATOR ASSEMBLY |
![]() |
Install the 2 bolts.
Install the fan shroud to the radiator assembly.
Install the 2 lower radiator supports.
![]() |
Install the radiator assembly with the fan shroud.
| 2. INSTALL NO. 2 FAN SHROUD |
![]() |
Install the No. 2 fan shroud with the 2 bolts.
![]() |
Connect the 6 water by-pass hose clamps to the No. 2 fan shroud.
![]() |
Connect the water by-pass hose to the radiator assembly.
![]() |
Connect the No. 1 water by-pass hose to the radiator assembly.
| 3. INSTALL AIR CLEANER CASE |
![]() |
Install the air cleaner case with the 3 bolts.
Connect the No. 4 water by-pass hose to the air cleaner case with the 3 clamps.
Install the air cleaner filter element.
| 4. INSTALL INLET AIR CLEANER ASSEMBLY |
![]() |
Install the inlet air cleaner assembly with the 2 bolts.
| 5. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Install the air cleaner cap sub-assembly with the 2 clamps and hose band.
Connect the air flow meter connector.
| 6. INSTALL HOOD LOCK SUPPORT SUB-ASSEMBLY |
![]() |
Install the upper radiator support with the 4 bolts.
Install the 2 cushions to the radiator support RH and radiator support LH.
![]() |
Install the radiator support RH and radiator support LH with the 2 bolts.
![]() |
Connect the 2 horn connectors.
![]() |
Connect the 2 wire harness clamps and connector to the fan shroud and cooling fan motor.
![]() |
Connect the connector to the No. 2 cooling fan motor.
![]() |
Connect the hood lock connector and hood lock control cable wire.
Connect the 3 wire harness clamps.
![]() |
Connect the water by-pass hose clamp to the radiator support RH.
| 7. INSTALL NO. 1 INVERTER BRACKET |
![]() |
Temporarily install the No. 1 inverter bracket with the 3 bolts.
Tighten the 3 bolts in the order shown in the illustration.
| 8. INSTALL MILLIMETER WAVE RADAR SENSOR BRACKET |
![]() |
Install the millimeter wave radar sensor bracket with the bolt.
| 9. INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System) |
![]() |
Tighten the 5 bolts on the millimeter wave radar sensor assembly.
Connect the connector.
| 10. INSTALL FRONT BUMPER ASSEMBLY |
w/ Headlight Cleaner System:
Connect the headlight cleaner hose.
Connect the connector.
![]() |
Install the front bumper assembly as shown in the illustration.
![]() |
Engage the 3 claws to install the front bumper assembly.
w/ Front Spoiler:
Engage the 2 guides and install the front spoiler cover.
Install the 2 clips and 2 screws.
Install the 7 clips.
Install the 2 bolts and 4 screws.
Install the screw.
![]() |
Install the pin hold clip.
| *a | Correct |
| *b | Incorrect |
| 11. CONNECT NO. 2 RADIATOR HOSE |
![]() |
Connect the No. 2 radiator hose to the radiator assembly with the clamp.
| 12. CONNECT NO. 1 RADIATOR HOSE |
![]() |
Connect the No. 1 radiator hose to the radiator assembly with the clamp.
| 13. ADD COOLANT (for Engine) |
Tighten the radiator drain cock plug.
Remove the reservoir tank cap.
![]() |
Add coolant to B line of the reservoir tank.
| *1 | B Line |
| Item | Capacity |
| Engine coolant | w/ Exhaust Heat Recirculation System: 7.2 liters (7.6 US qts, 6.3 lmp. qts) |
| w/o Exhaust Heat Recirculation System: 6.5 liters (6.8 US qts, 5.7 lmp. qts) |
Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the reservoir tank cap.
Put the engine in inspection mode (Click here).
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.
![]() |
After the engine has cooled down, check that the coolant level is between full and low.
| *1 | Full Line |
| *2 | Low Line |
| 14. INSPECT FOR COOLANT LEAK (for Engine) |
Remove the reservoir tank cap.
![]() |
Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.
Put the engine in inspection mode (Click here).
Warm up the engine.
Using the reservoir cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump assembly for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
Remove the radiator cap tester.
Install the reservoir tank cap.
| 15. INSTALL ENGINE UNDER COVER |
| 16. INSTALL FRONT SPOILER COVER (w/ Front Spoiler) |
| 17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 18. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 19. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 20. INSTALL REAR NO. 2 FLOOR BOARD |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 21. INSTALL RADIATOR SUPPORT OPENING COVER |
Engage the 2 claws and install the radiator support opening cover.
Install the 3 clips.
| 22. ADD WINDSHIELD WASHER FLUID (w/ Headlight Cleaner System) |
Add washer fluid to the washer jar.
| 23. PREPARATION VEHICLE FOR FOG LIGHT AIM ADJUSTMENT |
Prepare the vehicle:
| 24. PREPARATION FOR FOG LIGHT AIMING |
![]() |
Prepare the vehicle (except Taiwan and Indonesia):
![]() |
Prepare the vehicle (for Taiwan and Indonesia):
Prepare a piece of thick white paper (approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.
Draw a vertical line down the center of the screen (V line).
Set the screen as shown in the illustration (except Taiwan and Indonesia).

Set the screen as shown in the illustration (for Taiwan and Indonesia).

![]() |
Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
H Line (Fog light height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.
V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the fog light bulbs).
| 25. INSPECT FOG LIGHT AIMING |
Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.
Start the engine.
Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration (except Taiwan and Indonesia).

Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration (for Taiwan and Indonesia).

| 26. ADJUST FOG LIGHT AIMING (w/ Fog Light) |
![]() |
Adjust the aim vertically:
Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.
| *1 | Aiming Screw |
| 27. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System) |
![]() |
| *1 | Approx. 10 m |
| *2 | Approx. 14 m |
Before adjusting the radar beam axis, prepare the vehicle as follows.
Check the tire pressure and adjust it if necessary.
Remove all excess weight from the vehicle (luggage, heavy objects, etc.).
![]() |
Check and adjust the vertical direction of the radar sensor.
| *1 | Level |
Remove dust, oil and foreign matter from the radar sensor's level rack.
Set a level on the radar sensor's level rack.
![]() |
Check that the level's air bubble is within the red frame.
| *1 | FR |
| *2 | LH |
| *3 | Level |
| *4 | Air Bubble |
| *5 | Bolt A |
| Adjustment Direction | Adjustment Procedure | Adjustment Angle |
| Vertical adjustment | Upward direction: Turn bolt A to negative (-) side | For every 1.4 rotations of adjustment bolt, sensor moves about 1° |
| Downward direction: Turn bolt A to positive (+) side |
![]() |
Adjust the reflector height.
| *1 | Millimeter Wave Radar Sensor |
Adjust the reflector so that the center of SST reflector is the same height as the millimeter wave radar sensor.
![]() |
Place the reflector.
Hang the string (with weight) from the center of the vehicle's rear emblem. Mark the vehicle's rear center point on the ground. Repeat for the front of the vehicle.
![]() |
Set one end of the 10 m (32.8 ft.) string on the vehicle's rear center point. Run the string over the vehicle's front center point to a position 5 m (16.4 ft.) beyond the vehicle's front center point, as shown in the illustration. Mark the 5 m (16.4 ft.) position.
Using a tape measure, measure 15.7 mm (0.618 in.) to the right of the 5 m (16.4 ft.) position. Place the reflector at that position.

| *1 | Reflector Placement Point | *2 | Millimeter Wave Radar Sensor Position |
Check the radar beam axis.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on, and turn the cruise control main switch on.
Select "Auto" from the intelligent tester display screen.
Select "Radar Cruise" from the display screen.
Select "Utility" from the display screen.
Select "Beam Axis Adjustment" from the display screen.
Follow the tester display, and select "Next".
Check the following items on the laser cruise divergence data screen.
Check and adjust the horizontal direction of the radar sensor.
Check that the divergence of the radar beam axis is 0°.
![]() |
Based on the measured divergence of the beam axis, turn and adjust the bolt B for horizontal adjustment of the millimeter wave radar sensor using a screwdriver.
| *1 | Bolt B |
| Adjustment Direction | Adjustment Procedure | Adjustment Angle |
| Horizontal adjustment | Right direction: Turn bolt B to positive (+) side. | For every 2.5 rotations of adjustment bolt, sensor moves about 1° |
| Left direction: Turn bolt B to negative (-) side. |
Select "Next". The driving learning value is automatically reset.
Disconnect the intelligent tester from the DLC3.
Recheck and readjust the vertical direction of the radar sensor.
![]() |
Set a level on the radar sensor's level rack.
| *1 | Level |
![]() |
Check that the level's air bubble is within the red frame.
| *1 | FR |
| *2 | LH |
| *3 | Level |
| *4 | Air Bubble |
| *5 | Bolt A |
| Adjustment Direction | Adjustment Procedure | Adjustment Angle |
| Vertical adjustment | Upward direction: Turn bolt A to negative (-) side | For every 1.4 rotations of adjustment bolt, sensor moves about 1° |
| Downward direction: Turn bolt A to positive (+) side |