Home › Engine / Hybrid System › 2ZR-FXE COOLING › RADIATOR

RADIATOR > REMOVAL

for Preparation Click here



1. PRECAUTION (w/ Navigation System for HDD)

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE RADIATOR SUPPORT OPENING COVER


    B228429
  1. Remove the 3 clips.

  1. Disengage the 2 claws and remove the radiator support opening cover.



3. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



4. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



5. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



6. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



7. REMOVE FRONT SPOILER COVER (w/ Front Spoiler)


8. REMOVE ENGINE UNDER COVER


9. DRAIN ENGINE COOLANT (for Engine)

NOTICE:
Do not remove the reservoir tank cap, cylinder block drain cock plugs and radiator drain cock plug while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the local regulations.



  1. Loosen the cylinder block drain cock plug.

    HINT:
    The plug is on the back of the generator on the exhaust manifold side.



    A216061E01


    Text in Illustration 
    *1
    Reservoir Tank Cap
    *2
    Cylinder Block Drain Cock Plug
    *3
    Radiator Drain Cock Plug
    *4
    Air Release Valve



10. DISCONNECT NO. 1 RADIATOR HOSE


    A213428
  1. Disconnect the No. 1 radiator hose from the radiator assembly.



11. DISCONNECT NO. 2 RADIATOR HOSE


    A213429
  1. Disconnect the No. 2 radiator hose from the radiator assembly.



12. REMOVE FRONT BUMPER ASSEMBLY


    B228430E01
  1. Put protective tape around the front bumper assembly.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Use the same procedure for the RH side and LH side.



    B228431
  1. Using a screwdriver, turn the pins 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.



    B228433
  1. Remove the screw.

    HINT:
    Use the same procedure for the RH side and LH side.



    B228434
  1. Remove the 2 bolts and 4 screws.

  1. Using a clip remover, remove the 7 clips.



    B228436
  1. Using a clip remover, remove the 2 clips. (w/ Front Spoiler)

  1. Remove the 2 screws. (w/ Front Spoiler)

  1. Disengage the 2 guides and remove the front spoiler cover. (w/ Front Spoiler)



    B228439
  1. Disengage the 3 claws and remove the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect each connector.

  1. Disconnect the headlight cleaner hose and drain the washer fluid. (w/ Headlight Cleaner System)

    HINT:
    Use a container to collect the washer fluid.



    B228441
  1. Remove the front bumper assembly as shown in the illustration.



13. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)


    E186309
  1. Disconnect the connector.

  1. Remove the 5 bolts and millimeter wave radar sensor assembly.



14. REMOVE MILLIMETER WAVE RADAR SENSOR BRACKET


  1. w/o Dynamic Radar Cruise Control System:



      E189069
    1. Remove the 3 bolts and millimeter wave radar sensor bracket.



  1. w/ Dynamic Radar Cruise Control System:



      E189068
    1. Remove the bolt and millimeter wave radar sensor bracket.



15. REMOVE NO. 1 INVERTER BRACKET


    A209685
  1. Remove the 3 bolts and No. 1 inverter bracket.



16. REMOVE HOOD LOCK SUPPORT SUB-ASSEMBLY


    A216553
  1. Disconnect the water by-pass hose clamp from the radiator support RH.



    A213437
  1. Disconnect the hood lock connector and hood lock control cable wire.

  1. Disconnect the 3 wire harness clamps.



    A216556
  1. Disconnect the connector from the No. 2 cooling fan motor.



    A216557
  1. Disconnect the 2 wire harness clamps and connector from the fan shroud and cooling fan motor.



    A213427
  1. Disconnect the 2 horn connectors.



    A216554
  1. Remove the 2 bolts, radiator support RH and radiator support LH with the 2 cushions from the upper radiator support.



    A213431
  1. Remove the 4 bolts and upper radiator support.



17. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A213021
  1. Disconnect the air flow meter connector.

  1. Disconnect the 2 clamps and hose band, and remove the air cleaner cap sub-assembly.

  1. Remove the air cleaner filter element.



18. REMOVE INLET AIR CLEANER ASSEMBLY


    A212313
  1. Separate the water by-pass hose from the inlet air cleaner assembly.

  1. Separate the wire harness clamp from the inlet air cleaner assembly.

  1. Remove the 3 bolts and inlet air cleaner assembly.



19. REMOVE AIR CLEANER CASE


    A213023
  1. Separate the No. 4 water by-pass hose from the air cleaner case.

  1. Remove the 3 bolts and air cleaner case.



20. REMOVE NO. 2 FAN SHROUD


    A213434
  1. Disconnect the No. 1 water by-pass hose from the radiator assembly.



    A213435
  1. Disconnect the water by-pass hose from the radiator assembly.



    A216555
  1. Disconnect the 6 water by-pass hose clamps from the No. 2 fan shroud.



    A213432
  1. Remove the 2 bolts and No. 2 fan shroud from the radiator assembly.



21. REMOVE RADIATOR ASSEMBLY


    A219055
  1. Remove the radiator assembly with the fan shroud.

    NOTICE:
    For vehicles with the air conditioning system, do not apply any excessive force to the cooler condenser assembly or pipe when removing the radiator assembly.

  1. Remove the 2 lower radiator supports.



    A216559
  1. Remove the 2 bolts.

  1. Remove the fan shroud from the radiator assembly.