Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > REMOVAL

for Preparation Click here



1. REMOVE FRONT WIPER ARM HEAD CAP


    E190045E01
  1. Using a screwdriver, disengage the 3 claws and remove the front wiper arm head cap.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure for the RH side and LH side.



2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E190049
  1. Remove the nut and the front wiper arm and blade assembly LH.



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E190048
  1. Remove the nut and the front wiper arm and blade assembly RH.



4. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E193124E01
  1. Using a screwdriver, disengage the claw and guide <A> as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the guide <B> and remove the cowl side ventilator sub-assembly LH as shown in the illustration.



5. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


    E190113
  1. Remove the 2 clips.



  1. Disengage the 5 claws and 3 guides <A>.


    E190043E01

  1. Disengage the 8 guides <B> and pull out the cowl top ventilator louver sub-assembly as shown in the illustration.



7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


    E187016
  1. Remove the 2 clips.



  1. Disengage the 6 claws and 3 guides <A>.


    E187004E01

  1. Disengage the 8 guides <B> and pull out the cowl top ventilator louver sub-assembly as shown in the illustration.



8. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    E189311
  1. Disconnect the rain sensor cover as shown in the illustration.

  1. Disengage the 2 claws and remove the rain sensor cover.



9. REMOVE RAIN SENSOR (w/ Rain Sensor)


    E189314
  1. Disconnect the connector.



    E189312E01
  1. Release the stopper by pulling the stopper down and disconnect the rain sensor as shown in the illustration.
    Text in Illustration 
    *1
    Stopper



10. REMOVE INNER REAR VIEW MIRROR COVER (w/ EC Mirror)


    B229499
  1. Disengage the 2 claws and slide the inner rear view mirror cover as shown in the illustration.



    B229500
  1. Disengage the 6 claws and remove the inner rear view mirror cover.



11. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)


    B229503
  1. Disengage the 2 claws and disconnect the inner rear view mirror cover.



    B229504E01
  1. Remove the inner rear view mirror as shown in the illustration.



12. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)


    B229506
  1. Disconnect the connector.

  1. Using "TORX" socket wrench (T20), remove the screw and inner rear view mirror assembly.



13. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


14. REMOVE FRONT PILLAR GARNISH LH


    B257021
  1. When removing the front pillar garnish LH, cover the shaded part in the illustration with a piece of cloth so that the interior parts will not be damaged.



    B257024E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip

    HINT:
    Make the front pillar garnish LH hang down from the front pillar garnish clip.



    B257019E01
  1. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.

    NOTICE:
    1. Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
    2. Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

    HINT:
    Tape the needle-nosed pliers tip before use.
    Text in Illustration 
    *1
    Protective Tape

  1. Disengage the 3 guides.



    B257022E01
  1. Disengage the claw while pressing the shaded part in the illustration in the direction indicated by the arrow (1).

  1. Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.



    B227780E01
  1. Protect the curtain shield airbag assembly.
    Text in Illustration 
    *1
    Adhesive Tape
    *2
    Protective Cover
    *3
    Curtain Shield Airbag Assembly

    1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



15. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure for the RH side and LH side.



16. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and LH side.



17. REMOVE ROOF TOP MOULDING


    B227832
  1. Using moulding remover B, disengage the 3 claws and 2 clips, and remove the roof top moulding.



18. REMOVE MAP LIGHT ASSEMBLY (w/o Sliding Roof)


    E189673
  1. Disengage the 4 clips and 2 guides as shown in the illustration.

  1. Disconnect the connector and remove the map light assembly.



19. REMOVE MAP LIGHT ASSEMBLY (w/ Sliding Roof)


    E189671
  1. Disengage the 4 clips and 2 guides as shown in the illustration.

  1. Disconnect the connector and remove the map light assembly.



20. REMOVE FRONT ASSIST GRIP ASSEMBLY


    B229260E01
  1. Using a clip remover, disengage the 4 claws.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    1. Gently pry on the assist grip covers as shown in the illustration to remove them.
    2. Tape the clip remover tip before use.

  1. Pull off the 2 assist grip covers by hand.



    B229261
  1. Disengage the 2 clips and remove the front assist grip assembly.

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the other front assist grip.



21. REMOVE VISOR BRACKET COVER LH


    B227807
  1. Using moulding remover B, disengage the 3 claws and remove the visor bracket cover LH.



22. REMOVE VISOR ASSEMBLY LH


    B227811
  1. Disengage the 2 clips and remove the visor assembly LH.



23. REMOVE VISOR BRACKET COVER RH

HINT:
Use the same procedure for the RH side and LH side.



24. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



25. REMOVE VISOR HOLDER


    B211697E01
  1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

  1. Disengage the 2 claws and remove the visor holder.

    HINT:
    Use the same procedure for the other visor holder.



26. REMOVE ROOF HEADLINING ASSEMBLY
  1. Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed.

    HINT:
    It is not necessary to completely remove the roof headlining assembly.



27. REMOVE WINDSHIELD GLASS SUB-ASSEMBLY


    B229123E01
  1. Apply protective tape to the installation position of the windshield glass sub-assembly on the vehicle body.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Apply protective tape to the installation surface to prevent it from being scratched.



    B229125E01
  1. Place matchmarks on the windshield glass sub-assembly and vehicle body on the locations indicated in the illustration.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Matchmarks are not necessary if the windshield glass assembly is not going to be reused.



    B275802E01
  1. Pass a piano wire between the vehicle body and glass from the interior as shown in the illustration.
    Text in Illustration 
    *1
    Piano Wire

  1. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

  1. Cut off the adhesive applied to the bottom of the windshield glass sub-assembly by pulling the piano wire under the glass.

    NOTICE:
    1. When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.
    2. To prevent the safety pad from being scratched when removing the windshield glass sub-assembly, place a plastic sheet between the piano wire and safety pad.



  1. While pushing back the lip of the molding with a screwdriver, pass a piano wire between the vehicle body and windshield glass sub-assembly so that both wire ends are in the interior as shown in the illustration.


    B275801E01


    Text in Illustration 
    *A
    1-piece type
    *B
    2-piece type
    *1
    Piano Wire
    *2
    Adhesive
    *3
    No. 1 Stopper
    *4
    No. 2 Stopper
    *a
    Lip of the molding
    *b
    Stopper

  1. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

  1. Cut off the adhesive by pulling the piano wire around the windshield glass sub-assembly.

    NOTICE:
    1. When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.
    2. To prevent the safety pad from being scratched when removing the windshield glass sub-assembly, place a plastic sheet between the piano wire and safety pad.
    3. When passing the piano wire below the 2 stoppers, make sure to cut the adhesive applied between the windshield glass sub-assembly and stoppers.
    4. Be careful not to drop the windshield glass sub-assembly.

  1. Using suction cups, remove the windshield glass sub-assembly .

    NOTICE:
    1. Be careful not to drop the windshield glass sub-assembly.
    2. Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.

  1. Remove the parts of the 2 No. 1 windshield glass stoppers (1-piece type) or 2 No. 2 windshield glass stoppers (2-piece type) that remain on the vehicle.



28. REMOVE WINDOW GLASS ADHESIVE DAM


    B229127
  1. Using a scraper, remove the windshield glass adhesive dam.

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the window glass adhesive dam with a new one.



29. REMOVE WINDSHIELD OUTSIDE MOULDING


    B229128
  1. Using a scraper, remove the windshield outside moulding.

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the windshield outside moulding with a new one.



30. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)


    B229130
  1. Remove the 2 No. 1 windshield glass stoppers.

    NOTICE:
    Be sure to replace the No. 1 windshield glass stoppers with new ones.



31. CLEAN WINDSHIELD GLASS


    B149736
  1. Using a scraper, remove the adhesive tape and adhesive sticking to the windshield glass.

    NOTICE:
    Be careful not to damage the windshield glass.

  1. Clean the outer circumference of the windshield glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the windshield glass surface after cleaning it.
    2. Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.



32. CLEAN VEHICLE BODY


    B149737E07
  1. Clean and shape the contact surfaces of the vehicle body.
    Text in Illustration 
    *1
    Adhesive
    *2
    Body

    1. Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.