WINDSHIELD GLASS > REMOVAL |
| 1. REMOVE FRONT WIPER ARM HEAD CAP |
![]() |
Using a screwdriver, disengage the 3 claws to remove the front wiper arm head cap.
| *1 | Protective Tape |
| 2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Remove the nut and the front wiper arm and blade assembly LH.
| 3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Remove the nut and the front wiper arm and blade assembly RH.
| 4. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH |
![]() |
Using a screwdriver, disengage the claw and guide <A> as shown in the illustration.
| *1 | Protective Tape |
Disengage the guide <B> and remove the cowl side ventilator sub-assembly LH as shown in the illustration.
| 5. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH |
| 6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
![]() |
Remove the 2 clips.
Disengage the 5 claws and 3 guides <A>.

Disengage the 8 guides <B> and pull out the cowl top ventilator louver sub-assembly as shown in the illustration.
| 7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
![]() |
Remove the 2 clips.
Disengage the 6 claws and 3 guides <A>.

Disengage the 8 guides <B> and pull out the cowl top ventilator louver sub-assembly as shown in the illustration.
| 8. REMOVE RAIN SENSOR COVER (w/ Rain Sensor) |
![]() |
Disconnect the rain sensor cover as shown in the illustration.
Disengage the 2 claws and remove the rain sensor cover.
| 9. REMOVE RAIN SENSOR (w/ Rain Sensor) |
![]() |
Disconnect the connector.
![]() |
Release the stopper by pulling the stopper down and disconnect the rain sensor as shown in the illustration.
| *1 | Stopper |
| 10. REMOVE INNER REAR VIEW MIRROR COVER (w/ EC Mirror) |
![]() |
Disengage the 2 claws and slide the inner rear view mirror cover as shown in the illustration.
![]() |
Disengage the 6 claws and remove the inner rear view mirror cover.
| 11. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror) |
![]() |
Disengage the 2 claws and disconnect the inner rear view mirror cover.
![]() |
Remove the inner rear view mirror as shown in the illustration.
| 12. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror) |
![]() |
Disconnect the connector.
Using "TORX" socket wrench (T20), remove the screw and inner rear view mirror assembly.
| 13. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 14. REMOVE FRONT PILLAR GARNISH LH |
![]() |
When removing the front pillar garnish LH, cover the shaded part in the illustration with a piece of cloth so that the interior parts will not be damaged.
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
| *1 | Front Pillar Garnish Clip |
![]() |
Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.
| *1 | Protective Tape |
Disengage the 3 guides.
![]() |
Disengage the claw while pressing the shaded part in the illustration in the direction indicated by the arrow (1).
Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.
![]() |
Protect the curtain shield airbag assembly.
| *1 | Adhesive Tape |
| *2 | Protective Cover |
| *3 | Curtain Shield Airbag Assembly |
Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.
| 15. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 16. REMOVE FRONT PILLAR GARNISH RH |
| 17. REMOVE ROOF TOP MOULDING |
![]() |
Using moulding remover B, disengage the 3 claws and 2 clips, and remove the roof top moulding.
| 18. REMOVE MAP LIGHT ASSEMBLY (w/o Sliding Roof) |
![]() |
Disengage the 4 clips and 2 guides as shown in the illustration.
Disconnect the connector and remove the map light assembly.
| 19. REMOVE MAP LIGHT ASSEMBLY (w/ Sliding Roof) |
![]() |
Disengage the 4 clips and 2 guides as shown in the illustration.
Disconnect the connector and remove the map light assembly.
| 20. REMOVE FRONT ASSIST GRIP ASSEMBLY |
![]() |
Using a clip remover, disengage the 4 claws.
Pull off the 2 assist grip covers by hand.
![]() |
Disengage the 2 clips and remove the front assist grip assembly.
Remove the 2 clips from the vehicle body.
| 21. REMOVE VISOR BRACKET COVER LH |
![]() |
Using moulding remover B, disengage the 3 claws and remove the visor bracket cover LH.
| 22. REMOVE VISOR ASSEMBLY LH |
![]() |
Disengage the 2 clips and remove the visor assembly LH.
| 23. REMOVE VISOR BRACKET COVER RH |
| 24. REMOVE VISOR ASSEMBLY RH |
| 25. REMOVE VISOR HOLDER |
![]() |
Turn the visor holder approximately 45° and pull it out as shown in the illustration.
Disengage the 2 claws and remove the visor holder.
| 26. REMOVE ROOF HEADLINING ASSEMBLY |
Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed.
| 27. REMOVE WINDSHIELD GLASS SUB-ASSEMBLY |
![]() |
Apply protective tape to the installation position of the windshield glass sub-assembly on the vehicle body.
| *1 | Protective Tape |
![]() |
Place matchmarks on the windshield glass sub-assembly and vehicle body on the locations indicated in the illustration.
| *1 | Matchmark |
![]() |
Pass a piano wire between the vehicle body and glass from the interior as shown in the illustration.
| *1 | Piano Wire |
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut off the adhesive applied to the bottom of the windshield glass sub-assembly by pulling the piano wire under the glass.
While pushing back the lip of the molding with a screwdriver, pass a piano wire between the vehicle body and windshield glass sub-assembly so that both wire ends are in the interior as shown in the illustration.

| *A | 1-piece type | *B | 2-piece type |
| *1 | Piano Wire | *2 | Adhesive |
| *3 | No. 1 Stopper | *4 | No. 2 Stopper |
| *a | Lip of the molding | *b | Stopper |
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut off the adhesive by pulling the piano wire around the windshield glass sub-assembly.
Using suction cups, remove the windshield glass sub-assembly .
Remove the parts of the 2 No. 1 windshield glass stoppers (1-piece type) or 2 No. 2 windshield glass stoppers (2-piece type) that remain on the vehicle.
| 28. REMOVE WINDOW GLASS ADHESIVE DAM |
![]() |
Using a scraper, remove the windshield glass adhesive dam.
| 29. REMOVE WINDSHIELD OUTSIDE MOULDING |
![]() |
Using a scraper, remove the windshield outside moulding.
| 30. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type) |
![]() |
Remove the 2 No. 1 windshield glass stoppers.
| 31. CLEAN WINDSHIELD GLASS |
![]() |
Using a scraper, remove the adhesive tape and adhesive sticking to the windshield glass.
Clean the outer circumference of the windshield glass with a non-residue solvent.
| 32. CLEAN VEHICLE BODY |
![]() |
Clean and shape the contact surfaces of the vehicle body.
| *1 | Adhesive |
| *2 | Body |
Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.
Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.