Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/o EGR System)

DTC    P0107    Manifold Absolute Pressure / Barometric Pressure Circuit Low Input

DTC    P0108    Manifold Absolute Pressure / Barometric Pressure Circuit High Input

for Preparation Click here


DESCRIPTION

The manifold absolute pressure sensor detects the intake manifold pressure as a voltage using a built-in sensor. The ECM calculates intake manifold pressure based on this voltage and also calculates the purge VSV opening amount according to changes in the intake manifold pressure, and detects errors in the pressure sensor using the changes in pressure.
A263608E01

DTC No.
DTC Detecting Condition
Trouble Area
P0107
The output voltage from the manifold absolute pressure sensor less than 0.5 V for 0.5 seconds (1 trip detection logic).
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. ECM
P0108
The output voltage from the manifold absolute pressure sensor more than 4.5 V for 0.5 seconds (1 trip detection logic).
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. ECM

HINT:
When DTC P0107 or P0108 is detected, check the manifold absolute pressure using intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP.


Manifold Absolute Pressure (kPa)
Malfunction
Approximately 0 kPa (0 mmHg)
  1. Short in PIM circuit to ground
  2. Short in PIM circuit to E2 circuit
  3. Open in VC circuit
130 kPa (975 mmHg) or higher
  1. Short in VC circuit to PIM circuit
  2. Open in PIM circuit
  3. Open in E2 circuit

WIRING DIAGRAM


A220563E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (MAP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP.

  1. Read the MAP value.

    OK:
    Same value as the actual atmospheric pressure.

HINT:
  1. Standard atmospheric pressure is 101 kPa (758 mmHg). For every 100 m (328 ft) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). The pressure also varies due to the weather (high atmospheric pressure, low atmospheric pressure).
  2. Also, check "Atmosphere Pressure" in the Data List.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
A209150E05
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D3-3 (VC) - D3-2 (E2)
    Power switch on (IG)
    4.75 to 5.25 V
    D3-1 (PIM) - D3-2 (E2)
    Power switch on (IG)
    3.0 to 5.0 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Manifold Absolute Pressure Sensor)

  1. Reconnect the manifold absolute pressure sensor connector.
    Result 
    Result
    Proceed to
    Outside standard range
    A
    Within standard range
    B



B
Go to step 4
A


3.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D3-3 (VC) - D28-72 (VCPM)
    Always
    Below 1 Ω
    D3-2 (E2) - D28-71 (EPIM)
    Always
    Below 1 Ω
    D3-1 (PIM) - D28-69 (PIM)
    Always
    Below 1 Ω
    D3-3 (VC) or D28-72 (VCPM) - Body ground
    Always
    10 kΩ or higher
    D3-1 (PIM) or D28-69 (PIM) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Replace the manifold absolute pressure sensor (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0107 OR P0108)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (IG) and wait for 5 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0107 or P0108 is output
    B



B
REPLACE ECM (Click here)
A

END