Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/o EGR System)

SFI SYSTEM (w/o EGR System) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under Normal Condition are reference only. Do not depend solely on these values when determining whether or not a part is faulty.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the tester on.

  4. Put the engine in inspection mode (maintenance mode) (Click here).

  5. Start the engine.

  6. Warm up the engine.

  7. Turn the A/C switch off.

  8. Turn the power switch off.

  9. Turn the power switch on (IG).

  10. Turn the tester on.

  11. Enter the following menus: Powertrain / Engine and ECT / Data List.

  12. According to the display on the tester, read the Data List.


Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed:
Min.: 0 km/h (0 mph),
Max.: 255 km/h (158 mph)
Actual vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed:
Min.: 0 rpm, Max.: 16383 rpm
950 to 1050 rpm: Idling
-
Calculate Load
Load calculated by ECM:
Min.: 0%, Max.: 100%
  1. 20 to 40%: Idling
  2. 15 to 35%: Running without load (2500 rpm)
-
Vehicle Load
Vehicle load:
Min.: 0%, Max.: 25700%
Actual vehicle load
Load percentage in terms of maximum intake air flow amount
MAF
Air flow rate from mass air flow meter sub-assembly:
Min.: 0 gm/sec, Max.: 655.35 gm/sec
1 to 3 gm/sec: Idling
4.5 to 8.5 gm/sec: Running without load (2500 rpm)
If value approximately 0.0 gm/sec:
  1. Mass air flow meter sub-assembly power source circuit open
  2. VG circuit open or short
If value 271.0 gm/sec or more:
  1. E2G circuit open
Atmosphere Pressure
Atmospheric pressure:
Min.: 0 kPa (0 mmHg) , Max.: 255 kPa (1913 mmHg)
Equivalent to atmospheric pressure (absolute pressure)
-
MAP
Intake manifold pressure:
Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1913 mmHg)
  1. 80 to 110 kPa (600 to 825 mmHg): Power switch on (IG)
  2. 20 to 40 kPa (150 to 300 mmHg): Idling
-
Coolant Temp
Engine coolant temperature:
Min.: -40°C (-40°F),
Max.: 140°C (284°F)
75 to 100°C (167 to 212°F):
After warming up
  1. If value -40°C (-40°F): sensor circuit open
  2. If value 140°C (284°F): sensor circuit shorted
Intake Air
Intake air temperature:
Min.: -40°C (-40°F),
Max.: 140°C (284°F)
Equivalent to temperature at location of mass air flow meter sub-assembly
  1. If value -40°C (-40°F): sensor circuit open
  2. If value 140°C (284°F): sensor circuit shorted
Engine Run Time
Engine run time:
Min.: 0 s (seconds),
Max.: 65535 s (seconds)
Time after power switch on (READY)
-
Initial Engine Coolant Temp
Initial engine coolant temperature:
Min.: -40°C (-40°F),
Max.: 119.3°C (246.7°F)
Coolant temperature when power switch is turned on (IG)
-
Initial Intake Air Temp
Initial intake air temperature:
Min.: -40°C (-40°F),
Max.: 119.3°C (246.7°F)
Intake air temperature when power switch is turned on (IG)
-
Battery Voltage
Auxiliary battery voltage:
Min.: 0 V, Max.: 65.535 V
11 to 16 V: Power switch on (IG)
-
Throttle Sensor Volt %
Throttle valve opening percentage according to throttle position sensor:
Min.: 0%, Max.: 100%
10 to 22%: Accelerator pedal fully released
Value calculated based on the voltage at terminal VTA1
Throttl Sensor #2 Volt %
Throttle valve opening percentage according to throttle position sensor No. 2:
Min.: 0%, Max.: 100%
42 to 62%: Accelerator pedal fully released
Value calculated based on the voltage at terminal VTA2
System Guard
System guard:
ON or OFF
ON
-
Throttle Idle Position
Whether or not throttle position sensor detecting idle:
ON or OFF
-
-
Throttle Require Position
Required throttle position:
Min.: 0 V, Max.: 4.98 V
0.5 to 1.1 V: Idling
-
Throttle Sensor Position*1
Throttle sensor position:
Min.: 0%, Max.: 100%
0%: Accelerator pedal fully released
Recognition value for throttle opening angle on ECM
Throttle Position No. 1
Throttle position sensor No. 1 output voltage:
Min.: 0 V, Max.: 4.98 V
  1. 0.5 to 1.1 V: Accelerator pedal fully released
  2. 0.6 to 1.4 V: Fail-safe operating
-
Throttle Position No. 2
Throttle position sensor No. 2 output voltage:
Min.: 0 V, Max.: 4.98 V
  1. 2.1 to 3.1 V: Accelerator pedal fully released
  2. 2.1 to 3.1 V: Fail-safe operating
-
Throttle Position Command
Throttle position command value:
Min.: 0 V, Max.: 4.98 V
-
-
Throttle Sens Open Pos #1
Throttle sensor opener position No. 1:
Min.: 0 V, Max.: 4.98 V
0.6 to 1.4 V
-
Throttle Sens Open Pos #2
Throttle sensor opener position No. 2:
Min.: 0 V, Max.: 4.98 V
1.7 to 2.5 V
-
Throttle Motor Current
Throttle actuator current:
Min.: 0 A, Max.: 19.9 A
0 to 3.0 A: Idling
-
Throttle Motor DUTY
Throttle actuator:
Min.: 0%, Max.: 100%
10 to 22%: Idling after engine warmed up
-
Throttle Motor Duty (Open)
Throttle actuator duty ratio (open):
Min.: 0%, Max.: 255%
0 to 40%: Idling
-
Throttle Motor Duty (Close)
Throttle actuator duty ratio (close):
Min.: 0%, Max.: 255%
0 to 40%: Idling
-
Throttle Fully Close Learn
Throttle valve fully closed
(learned value):
Min.: 0 V, Max.: 4.98 V
0.4 to 1.0 V: Accelerator pedal fully released
-
+BM Voltage
+BM voltage:
Min.: 0 V, Max.: 79.998 V
11 to 16 V: Power switch on (IG) and system normal
-
Actuator Power Supply
Actuator power supply
ON or OFF
ON: Idling
-
Injector (Port)
Injection period of the No. 1 cylinder:
Min.: 0 μs, Max.: 65535 μs
1000 to 3000 μs: Idling
-
Injection Volum (Cylinder1)
Injection volume (Cylinder 1):
Min.: 0 ml, Max.: 2.047 ml
0.03 to 0.13 ml: Idling
Quantity of fuel injection volume for 10 injections
Fuel Pump/Speed Status
Fuel pump status:
ON or OFF
ON: Engine running
-
EVAP (Purge) VSV
Purge VSV control duty:
Min.: 0%, Max.: 100%
0 to 50%: Idling, under purge control
Order signal from ECM
Evap Purge Flow
Purge flow:
Min.: 0%, Max.: 399.9%
0 to 10%: Idling
-
Purge Density Learn Value
Purge density learned value:
Min.: -200, Max.: 199.993
-40 to 10: Idling
-
EVAP Purge VSV
VSV status for EVAP control:
ON or OFF
-
-
Purge Cut VSV Duty
Purge VSV duty:
Min.: 0%, Max.: 399.9%
-
-
Target Air-Fuel Ratio
Target air fuel ratio:
Min.: 0, Max.: 1.99
0.8 to 1.2: During idling
-
AF Lambda B1S1
Output air fuel ratio associated with bank 1 sensor 1:
Min.: 0, Max.: 1.99
  1. Value less than 1 (0.000 to 0.999) = Rich
  2. Stoichiometric air fuel ratio = 1
  3. Value greater than 1 (1.001 to 1.99) = Lean
-
AFS Voltage B1S1
Air fuel ratio sensor output voltage for bank 1 sensor 1:
Min.: 0 V, Max.: 7.99 V
2.6 to 3.8 V: Idling, engine warmed up
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensors
AFS Current B1S1
Air fuel ratio sensor output current for bank 1 sensor 1:
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling, engine warmed up
Value becomes higher when fuel-cut executed under high engine speed
A/F Heater Duty #1
Air fuel ratio sensor heater duty ratio for bank 1:
Min.: 0%, Max.: 399.9%
0 to 100%
-
O2S B1S2
Heated oxygen sensor output voltage for bank 1 sensor 2:
Min.: 0 V, Max.: 1.275 V
0 to 0.9 V: Driving at 70 km/h (43 mph)
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensors
O2 Heater B1S2
Heated oxygen sensor heater for bank 1 sensor 2:
Not Act or Active
-
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current for bank 1 sensor 2:
Min.: 0 A, Max.: 4.999 A
-
-
Short FT #1
Short-term fuel trim of bank 1:
Min.: -100%, Max.: 99.2%
-20 to 20%
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
Long FT #1
Long-term fuel trim of bank 1:
Min.: -100%, Max.: 99.2%
-20 to 20%
  1. Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value
  2. Air-fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and separate value are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range.
    [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the learned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.
A/F Learn Value Idle #1
Idle area of air fuel ratio learn value:
Min.: -50%, Max.: 49.6%
-20 to 20%
Learning is performed when idling with the engine warmed up (coolant temperature is 80°C [176°F] or higher).
A/F Learn Value Low #1
Low load area of air fuel ratio learn value:
Min.: -50%, Max.: 49.6%
-20 to 20%
Learning is performed when driving with the engine warmed up (coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid1 #1
Middle 1 load area of air fuel ratio learn value:
Min.: -50%, Max.: 49.6%
-20 to 20%
Learning is performed when driving with the engine warmed up (coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid2 #1
Middle 2 load area of air fuel ratio learn value:
Min.: -50%, Max.: 49.6%
-20 to 20%
Learning is performed when driving with the engine warmed up (coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts).
A/F Learn Value High #1
High load area of air fuel ratio learn value:
Min.: -50%, Max.: 49.6%
-20 to 20%
Learning is performed when driving with the engine warmed up (coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
Total FT #1
Total fuel trim of bank 1 (Average value for fuel trim system of bank 1):
Min.: -0.5, Max.: 0.496
-0.28 to 0.2: Idling
-
Fuel System Status #1
Unused, Fuel system status (bank 1):
OL, CL, OLDrive, OLFault, CLFault or Unused
CL: Idling after warming up
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
  3. OLDrive: Open loop due to driving conditions (fuel enrichment)
  4. OLFault: Open loop due to detected system fault
  5. CLFault: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning
Fuel System Status #2
Unused, Fuel system status (bank 2):
OL, CL, OLDrive, OLFault, CLFault or Unused
Unused
-
IGN Advance
Ignition timing advance for No. 1 cylinder:
Min.: -64 deg, Max.: 63.5 deg
BTDC 0 to 16 deg.: Idling
-
Knock Feedback Value
Knocking feedback value:
Min.: -1024°CA, Max.: 1023.9°CA
-20 to 0°CA:
Driving at 70 km/h (43 mph)
-
Knock Correct Learn Value
Knocking correction learned value:
Min.: -1024°CA, Max.: 1023.9°CA
0 to 22°CA:
Driving at 70 km/h (43 mph)
-
VVT Control Status #1
Variable valve timing (VVT) control status for bank 1:
ON or OFF
-
-
VVT Aim Angle #1*2
VVT hold duty learned value for bank 1:
Min.: 0%, Max.: 399.9%
-
VVT duty signal value during intrusive operation
VVT Change Angle #1*2
VVT displacement angle for bank 1:
Min.: 0 DegFR, Max.: 639.9 DegFR
-
Displacement angle during intrusive operation
VVT OCV Duty #1*2
VVT camshaft timing oil control valve assembly operation duty for bank 1:
Min.: 0%, Max.: 399.9%
-
Requested duty value for intrusive operation
VN Turbo Type
Variable nozzle turbo type:
Not Avl or Commo or Vacuum or CAN Com
Not Avl (Unused)
-
Catalyst Temp B1S1
Catalyst temperature bank 1 sensor 1:
Min.: -40°C (-40°F),
Max.: 6513.5°C (11756.3°F)
-
-
Catalyst Temp B1S2
Catalyst temperature bank 1 sensor 2:
Min.: -40°C (-40°F),
Max.: 6513.5°C (11756.3°F)
-
-
Closed Throttle Position SW
Closed throttle position switch:
ON or OFF
-
-
Fuel Cut Condition
Fuel cut condition:
ON or OFF
ON: Fuel cut operating or engine stopped
-
Check Mode
Check mode:
ON or OFF
ON: Check mode ON
Refer to Check Mode Procedure (Click here)
Misfire Test Result
Check mode result for misfire monitor:
Compl or Incmpl
-
-
OXS1 Test Result
Check mode result for heated oxygen sensor (bank 1):
Compl or Incmpl
-
-
A/F Test Results #1
Check mode result for air fuel ratio sensor (bank 1)
Compl or Incmpl
-
-
Complete Parts Monitor
Comprehensive component monitor:
Not Avl or Avail
-
-
Fuel System Monitor
Fuel system monitor:
Not Avl or Avail
-
-
Misfire Monitor
Misfire monitor:
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor:
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor:
Compl or Incmpl
-
-
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor:
Not Avl or Avail
-
-
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor:
Compl or Incmpl
-
-
O2S(A/FS) Monitor
O2S (A/FS) monitor:
Not Avl or Avail
-
-
O2S(A/FS) Monitor
O2S (A/FS) monitor:
Compl or Incmpl
-
-
A/C Monitor
A/C monitor:
Not Avl or Avail
-
-
A/C Monitor
A/C monitor:
Compl or Incmpl
-
-
2nd Air Monitor
2nd air monitor:
Not Avl or Avail
-
-
2nd Air Monitor
2nd air monitor:
Compl or Incmpl
-
-
EVAP Monitor
EVAP monitor:
Not Avl or Avail
-
-
EVAP Monitor
EVAP monitor:
Compl or Incmpl
-
-
Heated Catalyst Monitor
Heated catalyst monitor:
Not Avl or Avail
-
-
Heated Catalyst Monitor
Heated catalyst monitor:
Compl or Incmpl
-
-
Catalyst Monitor
Catalyst monitor:
Not Avl or Avail
-
-
Catalyst Monitor
Catalyst monitor:
Compl or Incmpl
-
-
TC Terminal
TC terminal status:
ON or OFF
-
-
# Codes (Include History)
Number of codes:
Min.: 0
Max.: 255
0: No emission related DTC detected
-
MIL
MIL status:
ON or OFF
ON: MIL ON
-
MIL ON Run Distance
Distance driven with MIL on:
Min.: 0 Km (0 mile),
Max.: 65535 Km (40723 mile)
Distance after DTC detected
-
Running Time from MIL ON
Running time from MIL on:
Min.: 0 min,
Max.: 65535 min
Equivalent to running time after MIL turned on
-
Time after DTC Cleared
Time after DTCs cleared:
Min.: 0 min,
Max.: 65535 min
Equivalent to time after DTCs cleared
-
Distance from DTC Cleared
Distance driven after DTCs cleared:
Min.: 0 km (0 mile),
Max.: 65535 km (40723 mile)
Equivalent to distance driven after DTCs cleared
-
Warmup Cycle Cleared DTC
Warmup cycles after DTCs cleared:
Min.: 0, Max.: 255
-
Number of warm-up cycles after DTCs cleared
Dist Batt Cable Disconnect
Distance driven after auxiliary battery cable disconnected:
Min.: 0 km (0 mile), Max.: 65535 km (40723 mile)
Total distance vehicle driven after auxiliary battery cable disconnected
-
OBD Requirements
OBD requirement
Brazil OBD Phase 2
-
Number of Emission DTC
Emission related DTCs
Min.: 0
Max.: 127
-
Number of emission related DTCs
TC and TE1
TC and CG (TE1) terminals of DLC3:
ON or OFF
-
-
Ignition Trig. Count
Ignition counter:
Min.: 0, Max.: 65535
0 to 400
-
Cylinder #1 Misfire Count
Misfire count of cylinder 1:
Min.: 0, Max.: 255
0
-
Cylinder #2 Misfire Count
Misfire count of cylinder 2:
Min.: 0, Max.: 255
0
-
Cylinder #3 Misfire Count
Misfire count of cylinder 3:
Min.: 0, Max.: 255
0
-
Cylinder #4 Misfire Count
Misfire count of cylinder 4:
Min.: 0, Max.: 255
0
-
All Cylinders Misfire Count
Misfire count of all cylinders:
Min.: 0, Max.: 255
0
-
Misfire RPM
Engine speed for first misfire range:
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Misfire 0
-
Misfire Load
Engine load for first misfire range:
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: Misfire 0
-
Misfire Margin
Misfire monitoring:
Min.: -128%, Max.: 127%
0 to 127%: Idling
Misfire detecting margin
Electric Fan Motor
Electric fan motor:
ON or OFF
-
-
Idle Fuel Cut
Fuel cut idle:
ON or OFF
ON: Fuel cut operating
Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is high.
FC TAU
Fuel cut TAU (fuel cut with very light load):
ON or OFF
ON: Fuel cut operating
This is the fuel cut performed under a very light load to prevent the engine combustion from becoming incomplete.
Communication with HV
Status of communication with the power management control ECU:
Comm or No Comm
Comm: Power switch on (IG)
-
Communication with Brake
Status of communication with the skid control ECU:
Comm or No Comm
Comm: Power switch on (IG)
-
Comm with Air Conditioner
Status of communication with the air conditioning amplifier assembly:
Comm or No Comm
Comm: Power switch on (IG)
-
Model Code
Model code
-
Used for identifying the model code:
ZVW3##
Engine Type
Engine type
-
Used for identifying the engine type:
2ZRFXE
Cylinder Number
Number of cylinders:
Min.: 0, Max.: 255
-
Used for identifying the number of cylinders:
4
Destination
Destination
-
Used for identifying the destination:
W
Model Year
Model year:
Min.: 1900, Max.: 2155
-
Used for identifying the model year:
20##
System Identification
System identification
-
Used for identifying the engine system:
HV (Hybrid)
Engine Speed of Cyl #1
Engine speed for cylinder 1:
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Engine Speed of Cyl #2
Engine speed for cylinder 2:
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Engine Speed of Cyl #3
Engine speed for cylinder 3:
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Engine Speed of Cyl #4
Engine speed for cylinder 4:
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Av Engine Speed of All Cyl
Engine speed for all cylinders:
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Sports Mode Switch
Pattern select switch status:
ON or OFF
-
-
Requested Engine Torque
Requested engine torque:
Min.: 0 kW, Max.: 16383.75 kW
0 to 73 kW
Flag information for hybrid vehicle
HV Target Engine Speed
Hybrid target engine speed:
Min.: 0 rpm, Max.: 6375 rpm
0 to 5200 rpm
Flag information for hybrid vehicle
Actual Engine Torque
Actual engine torque:
Min.: -32768 Nm, Max.: 32767 Nm
Actual engine torque
Flag information for hybrid vehicle
Engine Run Time
Engine run time:
Min.: 0 s (seconds), Max.: 255 s (seconds)
0 to 255 s
Flag information for hybrid vehicle
Request Engine Run Time
Request engine run time:
Min.: 0 s (seconds), Max.: 25.5 s (seconds)
0 to 25.5 s
Flag information for hybrid vehicle
Judge Time Engine Ignition
Judgment time for complete explosion of ignition:
Min.: 0 s (seconds), Max.: 25.5 s (seconds)
0 to 25.5 s
Flag information for hybrid vehicle
Judge Time Engine Output
Judgment time for time until engine output:
Min.: 0 s (seconds), Max.: 25.5 s (seconds)
0 to 25.5 s
Flag information for hybrid vehicle
Fuel Level
Fuel level:
Empty or Not Emp
-
Flag information for hybrid vehicle
ISC Learning
ISC learning:
Compl or Incmpl
-
Flag information for hybrid vehicle
F/C for Engine Stop Req
Fuel cut for engine stop request:
ON or OFF
-
Flag information for hybrid vehicle
Engine Independent
Engine independent operation:
Not Opr or Operate
-
Flag information for hybrid vehicle
Racing Operation
Racing operation:
Not Opr or Operate
-
Flag information for hybrid vehicle
Request Warm-up
Request engine warm up:
Not Req or Request
-
Flag information for hybrid vehicle
Engine Independent Control
Engine independent control operation:
Not Opr or Operate
-
Flag information for hybrid vehicle
Elec Water Pump Target Spd
Engine water pump assembly target speed
Min.: 0 rpm, Max.: 6375 rpm
-
-
Elec Water Pump Spd
Engine water pump assembly speed
Min.: 0 rpm, Max.: 6375 rpm
-
-
ISC Learning Value
ISC learning value:
Min.: 0 L/s, Max.: 79.998 L/s
0.5 to 6.1 L/s: Idling
Flag information for hybrid vehicle

HINT:
  1. Normal condition: If no idling conditions are specified, the shift lever should be in N or P, and the A/C switch and all accessory switches should be off.
  2. *1: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).
  3. *2: Values are only displayed when performing the Active Tests: Control the VVT Linear (Bank 1) and Control the VVT System (Bank 1). For other Active Tests, the value will be 0.


ACTIVE TEST

HINT:
Using the intelligent tester to perform the Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the tester on.

  4. Put the engine in inspection mode (maintenance mode) (Click here).

  5. Start the engine.

  6. Warm up the engine.

  7. Turn the power switch off.

  8. Turn the power switch on (IG).

  9. Turn the tester on.

  10. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  11. According to the display on the tester, perform the Active Test.


Tester Display
Test Part
Control Range
Diagnostic Note
Control the Injection Volume
Change injection volume
Between -12.5 and 24.8%
  1. All fuel injectors are tested at the same time.
  2. Perform the test at or below 3000 rpm.
  3. Injection volume can be changed in fine gradations within control range.
  4. Control the Injection Volume enables the checking and graphing of the air fuel ratio sensor and the heated oxygen sensor voltage outputs.
  5. To conduct the test, enter the following menus: Active Test / Control the Injection Volume / Data List / All Data / AFS Voltage B1S1 and O2S B1S2.
  6. During the Active Test, air fuel ratio feedback control and feedback learning are stopped.
  7. This Active Test should be performed in inspection mode (maintenance mode).
Control the Injection Volume for A/F Sensor
Change injection volume
-12.5%/0%/12.5%
  1. All injectors are tested at the same time.
  2. Perform the test at or below 3000 rpm.
  3. Control the Injection Volume for A/F Sensor enables the checking and graphing of the air fuel ratio sensor and the heated oxygen sensor voltage outputs.
  4. To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / AFS Voltage B1S1 and O2S B1S2.
  5. During the Active Test, air fuel ratio feedback control and feedback learning are stopped.
  6. This Active Test should be performed in inspection mode (maintenance mode).
Activate the VSV for Evap Control
Activate purge VSV control
ON/OFF
  1. The valve is opened with a 30% duty ratio.
  2. This Active Test should be performed in inspection mode (maintenance mode).
Control the Fuel Pump/Speed
Activate fuel pump
ON/OFF
Test possible when following conditions met:
  1. Power switch on (IG)
  2. Engine is stopped
Connect the TC and TE1
Turn on and off TC and TE1 connection
ON/OFF
  1. ON: TC and TE1 are connected
  2. OFF: TC and TE1 are disconnected
Control the Idle Fuel Cut Prohibit
Prohibit idling fuel cut control
ON/OFF
This Active Test should be performed in inspection mode (maintenance mode).
Control the Electric Cooling Fan
Control electric cooling fan
ON/OFF
-
Control the ETCS Open/Close Slow Speed
Throttle actuator
Closed/Open
Open: Throttle valve opens slowly
Test possible when following conditions met:
  1. Power switch on (IG)
  2. Engine is stopped
  3. Accelerator pedal is fully depressed (Accelerator pedal position: 58 degrees or more)
  4. Park (P) has been selected
Control the ETCS Open/Close Fast Speed
Throttle actuator
Closed/Open
Open: Throttle valve opens quickly
Control the VVT Linear (Bank1)
Control camshaft timing oil control valve assembly
-128 to 127% (This value added to present camshaft timing oil control valve control duty)
100%: Maximum advance
-100%: Maximum retard
  1. Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%.
  2. Test is possible during idle.
  3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
  4. Test not possible with park (P) selected during charge control. Move the shift lever to N to perform test.
  5. This Active Test should be performed in inspection mode (maintenance mode).
Control the VVT System (Bank1)
Turn on and off camshaft timing oil control valve assembly
ON/OFF
  1. Engine stalls or idles roughly when the camshaft timing oil control valve assembly is turned on.
  2. Engine runs and idles normally when the camshaft timing oil control valve assembly is off.
  3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
  4. Test not possible with park (P) selected during charge control. Move the shift lever to N to perform test.
  5. This Active Test should be performed in inspection mode (maintenance mode).
Control the Cylinder #1 Fuel Cut
Cylinder #1 injector fuel cut
ON/OFF
  1. Test is possible while the vehicle is stopped and the engine is idling.
  2. This Active Test should be performed in inspection mode (maintenance mode).
Control the Cylinder #2 Fuel Cut
Cylinder #2 injector fuel cut
ON/OFF
  1. Test is possible while the vehicle is stopped and the engine is idling.
  2. This Active Test should be performed in inspection mode (maintenance mode).
Control the Cylinder #3 Fuel Cut
Cylinder #3 injector fuel cut
ON/OFF
  1. Test is possible while the vehicle is stopped and the engine is idling.
  2. This Active Test should be performed in inspection mode (maintenance mode).
Control the Cylinder #4 Fuel Cut
Cylinder #4 injector fuel cut
ON/OFF
  1. Test is possible while the vehicle is stopped and the engine is idling.
  2. This Active Test should be performed in inspection mode (maintenance mode).
Control the All Cylinder Fuel Cut
All cylinder fuel cut
ON/OFF
  1. Test is possible while the vehicle is stopped and the engine is idling.
  2. This Active Test should be performed in inspection mode (maintenance mode).
Check the Cylinder Compression*1
Check the cylinder compression pressure (measure engine speed for each cylinder)
ON/OFF
  1. Test is possible while the vehicle is stopped and the engine is idling.
  2. This Active Test should be performed in inspection mode (maintenance mode).
Activate the Electric Water Pump
Engine water pump assembly speed control
0/3000 rpm
Test possible when either of the following condition is met:
  1. Engine coolant temperature is Below 100°C (212°F)
  2. Power switch on (IG)

HINT:
*1: While the Check the Cylinder Compression Active Test is being performed, if the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.

  1. Connect the intelligent tester to the DLC3.
  2. Turn the power switch on (IG) and turn the tester on.
  3. Put the engine in inspection mode (maintenance mode) (Click here).
  4. Start the engine and warm it up.
  5. Turn the power switch off.
  6. Turn the power switch on (IG) and turn the tester on.
  7. Put the engine in inspection mode (maintenance mode) (Click here).

    HINT:
    Do not start the engine.

  8. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

    HINT:
    To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

  9. Push the snapshot button to turn the snapshot function on.

    HINT:
    Using the snapshot function, data can be recorded during the Active Test.

  10. While the engine is not running, press the RIGHT or LEFT button to change the Check the Cylinder Compression to ON.
  11. Start the engine.
  12. Monitor the engine speed (Engine Speed of Cyl #1 to #4 and Av Engine Speed of All Cyl) displayed on the tester.

    NOTICE:
    If the Check the Cylinder Compression Active Test needs to be performed after it is turned ON and performed once, press the Exit button to return to the Active Test menu screen. Then perform the Check the Cylinder Compression Active Test again.

    HINT:
    1. At first, the tester display will show each cylinder's engine speed measurement to be extremely high. After the engine has started, each cylinder's engine speed measurement will change to the actual engine speed.
    2. As soon as the measurements are obtained, finish the Active Test.

  13. Stop the engine, and then change Check the Cylinder Compression to OFF after the engine stops.
  14. Push the snapshot button to turn the snapshot function off.
  15. Select "Stored Data" on the tester screen, select the recorded data and display the data as a graph.

    HINT:
    If the data is not displayed as a graph, the change of the values cannot be observed.

  16. Check the change in engine speed values.

    HINT:
    As the data values of the Active Test return to their default values when engine is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during engine running.