Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/ EGR System)

SFI SYSTEM (w/ EGR System) > FREEZE FRAME DATA

for Preparation Click here



DESCRIPTION
  1. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

    HINT:
    If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.


  1. A159471E01
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, five separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
    1. 3 data sets before the DTC was set.
    2. 1 data set when the DTC was set.
    3. 1 data set after the DTC was set.
    1. These data sets can be used to simulate the condition of the vehicle around the time of the occurrence the malfunction. The data may assist in identifying the cause of the malfunction, and judging whether it was temporary or not.

LIST OF FREEZE FRAME DATA

Tester Display
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed
-
Calculate Load
Calculated load by ECM
-
Vehicle Load
Vehicle load
Load percentage in terms of maximum intake air flow amount
MAF
Air flow rate from mass air flow meter sub-assembly
If value approximately 0.0 gm/sec:
  1. Mass air flow meter sub-assembly power source circuit open
  1. VG circuit open or short
If value 271.0 gm/sec or more:
  1. E2G circuit open
Atmosphere Pressure
Atmosphere pressure
-
MAP
Intake manifold pressure
-
Coolant Temp
Engine coolant temperature
  1. If value -40°C (-40°F): sensor circuit open
  1. If value 140°C (284°F): sensor circuit shorted
Intake Air
Intake air temperature
  1. If value -40°C (-40°F): sensor circuit open
  1. If value 140°C (284°F): sensor circuit shorted
Engine Run Time
Engine run time
-
Initial Engine Coolant Temp
Initial engine coolant temperature
Service data
Initial Intake Air Temp
Initial intake air temperature
Service data
Battery Voltage
Battery voltage
-
Throttle Sensor Volt %
Throttle sensor positioning
Recognition value for throttle opening angle on ECM
Throttl Sensor #2 Volt %
Absolute throttle sensor positioning #2
Recognition value for throttle opening angle on ECM
Throttle Sensor Position
Throttle sensor positioning
Recognition value for throttle opening angle on ECM
Throttle Motor DUTY
Throttle actuator
-
Injector (Port)
Injection direction for cylinder 1
-
Injection Volum (Cylinder1)
Injection volume (Cylinder 1)
Quantity of fuel injection volume for 10 times
Fuel Pump/Speed Status
Fuel pump/status
Active Test support data
EVAP (Purge) VSV
Purge VSV control duty ratio
Order signal from ECM
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
Service data
Purge Density Learn Value
Learning value of purge density
Service data
EVAP Purge VSV
Purge VSV status for EVAP control
Active Test support data
Purge Cut VSV Duty
Purge cut vacuum switching valve duty ratio
-
Target Air-Fuel Ratio
Ratio compared to stoichiometric level
-
AF Lambda B1 S1
Short-term fuel trim associated with bank 1 sensor 1
-
AFS Voltage B1 S1
Air fuel ratio sensor output voltage for bank 1 sensor 1
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensors
AFS Current B1 S1
Air fuel ratio sensor output current for bank 1 sensor 1
Value becomes higher when fuel-cut executed under high engine speed
A/F Heater Duty #1
Air fuel ratio sensor heater duty ratio
-
O2S B1 S2
Heated oxygen sensor output voltage for bank 1 sensor 2
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensors
O2S Impedance B1S2
Heated oxygen sensor impedance (bank 1 sensor 2)
-
O2 Heater B1S2
Heated oxygen sensor operation
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current
-
Short FT #1
Short-term fuel trim of bank 1
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
Long FT #1
Long-term fuel trim of bank 1
Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value
Total FT #1
Total fuel trim
-
Fuel System Status #1
Fuel system status (bank 1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  1. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
  1. OLDrive: Open loop due to driving conditions (fuel enrichment)
  1. OLFault: Open loop due to detected system fault
  1. CLFault: Closed loop but air fuel ratio sensor, which is used for fuel control, malfunctioning
Fuel System Status #2
Fuel system status (bank 2) (Unused)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  1. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
  1. OLDrive: Open loop due to driving conditions (fuel enrichment)
  1. OLFault: Open loop due to detected system fault
  1. CLFault: Closed loop but air fuel ratio sensor, witch is used for fuel control, malfunctioning
IGN Advance
Ignition timing advance for cylinder 1
-
Knock Feedback Value
Feedback value of knocking
Service data
Knock Correct Learn Value
Correction learning value of knocking
Service data
Target EGR Position
Target EGR position
-
EGR Step Position
EGR step position
-
VVT Control Status #1
VVT control (bank 1) status
Active Test support data
Catalyst Temp B1 S1
Catalyst temperature (associated sensor 1)
-
Catalyst Temp B1 S2
Catalyst temperature (associated sensor 2)
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition ON or OFF
-
TC Terminal
TC terminal status
-
Time after DTC Cleared
Time since DTCs cleared
-
Distance from DTC Cleared
Distance traveled since DTCs cleared
-
Warmup Cycle Cleard DTC
Warm-up cycles since DTCs cleared
Number of warm-up cycles since DTCs cleared
Dist Batt Cable Disconnect
Accumulated distance from battery cable disconnected
-
IG OFF Elapsed Time
Cumulative time after power switch off
-
TC and TE1
TC and CG (TE1) terminals of DLC3
Active Test support data
Ignition Trig. Count
Ignition counter to calculated misfire count
-
Cylinder #1 Misfire Count
Misfire count for cylinder 1
-
Cylinder #2 Misfire Count
Misfire count for cylinder 2
-
Cylinder #3 Misfire Count
Misfire count for cylinder 3
-
Cylinder #4 Misfire Count
Misfire count for cylinder 4
-
All Cylinders Misfire Count
All cylinders misfire count
-
Misfire RPM
Average engine speed when misfire occurs
-
Misfire Load
Average engine load when misfire occurred
-
Catalyst OT MF F/C
Catalyst over temperature misfire prevention F/C not available
-
Cat OT MF F/C History
Catalyst over temperature misfire prevention F/C history
-
Cat OT MF F/C Cylinder#1
Catalyst over temperature misfire prevention #1
-
Cat OT MF F/C Cylinder#2
Catalyst over temperature misfire prevention #2
-
Cat OT MF F/C Cylinder#3
Catalyst over temperature misfire prevention #3
-
Cat OT MF F/C Cylinder#4
Catalyst over temperature misfire prevention #4
-
Electric Fan Motor
Electric cooling fan motor
Active Test support data
Idle Fuel Cut Prohibit
Prohibition of fuel cut at idle
-
Idle Fuel Cut
Fuel cut idle
ON: When throttle valve fully closed and engine speed over 2800 rpm
FC TAU
FC TAU
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
Communication with HV
Status of the communication with power management control ECU
-
Communication with Brake
Status of the communication with skid control ECU
-
Comm with Air Conditioner
Status of the communication with air conditioning amplifier assembly
-
Requested Engine Torque
Requested engine torque
Flag information for hybrid vehicle
HV Target Engine Speed
HV target engine speed
Flag information for hybrid vehicle
Actual Engine Torque
Actual engine torque
Flag information for hybrid vehicle
Engine Run Time
Engine run time
Flag information for hybrid vehicle
Request Engine Run Time
Request engine run time
Flag information for hybrid vehicle
Judge Time Engine Ignition
Judgment time engine ignition
Flag information for hybrid vehicle
Judge Time Engine Output
Judgment time for time until engine output
Flag information for hybrid vehicle
ISC Learning
Idle speed control learning
Flag information for hybrid vehicle
F/C for Engine Stop Req
Fuel cut for engine stop request
Flag information for hybrid vehicle
Engine Independent
Engine independent operation
Flag information for hybrid vehicle
Racing Operation
Racing operation
Flag information for hybrid vehicle
Request Warm-up
Request engine warm up
Flag information for hybrid vehicle
Engine Independent Control
Engine independent control operation
Flag information for hybrid vehicle
Elec Water Pump Target Spd
Engine water pump assembly target speed
-
Elec Water Pump Spd
Engine water pump assembly speed
-
ISC Learning Value
Idle speed control leaning value
Flag information for hybrid vehicle