DTC P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) |
| DTC No. | Detection Condition | Trouble Area |
| P0016 | Deviation in crankshaft position sensor signal and camshaft position sensor signal (2 trip detection logic) |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0016 is output | A |
| DTC P0016 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (Click here).
Start the engine.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).
Check the engine speed while operating the camshaft timing oil control valve assembly using the tester.
| Tester Operation | Specified Condition |
| OFF | Normal engine speed |
| ON | Engine idles roughly or stalls (soon after camshaft timing oil control valve assembly switched from OFF to ON) |
Start the engine when the engine coolant temperature is 30°C (86°F) or less.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).
Check the engine speed while operating the camshaft timing oil control valve assembly using the tester with the engine coolant temperature at 50°C (122°F) or less.
| Tester Operation | Specified Condition |
| OFF | Normal engine speed |
| ON | Engine idles roughly or stalls (soon after camshaft timing oil control valve assembly switched from OFF to ON) |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Put the engine in inspection mode (Click here).
Start the engine and warm it up.
Allow the engine to idle for 5 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0016 is output | B |
|
| ||||
| A | ||
| ||
| 4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Remove the camshaft timing oil control valve assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 6.9 to 7.9 Ω |
| *1 | Component without harness connected (Camshaft Timing Oil Control Valve Assembly) |
![]() |
Connect the positive (+) battery terminal to terminal 1 and connect the negative (-) battery terminal to terminal 2. Check the valve operation.
Reinstall the camshaft timing oil control valve assembly (Click here).
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
Inspect the camshaft timing gear assembly (for intake camshaft) (Click here).
|
| ||||
| OK | |
| 6.INSPECT OIL CONTROL VALVE FILTER |
![]() |
Remove the oil control valve filter (Click here).
Check that the filter is not clogged.
Reinstall the oil control valve filter (Click here).
|
| ||||
| OK | |
| 7.ADJUST VALVE TIMING |
![]() |
| *1 | Top |
| *2 | Alignment Mark |
| *3 | No. 1 Cylinder at TDC Compression |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Put the engine in inspection mode (Click here).
Start the engine and warm it up.
Allow the engine to idle for 5 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0016 is output | B |
|
| ||||
| A | ||
| ||