DTC P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction |
DTC P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem |
DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0120 | Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic) |
|
| P0121 | Difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip detection logic) |
|
| P0122 | Output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic) |
|
| P0123 | Output voltage of VTA1 is 4.54 V or more for 2 seconds or more (1 trip detection logic) |
|
| P0220 | Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic) |
|
| P0222 | Output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic) |
|
| P0223 | Output voltage of VTA2 is 4.8 V or more, and VTA1 between 0.2 V and 2.02 V, for 2 seconds or more (1 trip detection logic) |
|
| P2135 | Either condition (a) or (b) met (1 trip detection logic): (a) Difference between output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more (b) Output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less, for 0.4 seconds or more |
|

| 1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
Disconnect the throttle body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D4-5 (VC) - D28-88 (VCTA) | Always | Below 1 Ω |
| D4-6 (VTA) - D28-90 (VTA1) | Always | Below 1 Ω |
| D4-4 (VTA2) - D28-89 (VTA2) | Always | Below 1 Ω |
| D4-3 (E2) - D28-111 (ETA) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D4-5 (VC) or D28-88 (VCTA) - Body ground | Always | 10 kΩ or higher |
| D4-6 (VTA) or D28-90 (VTA1) - Body ground | Always | 10 kΩ or higher |
| D4-4 (VTA2) or D28-89 (VTA2) - Body ground | Always | 10 kΩ or higher |
Reconnect the throttle body assembly connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF THROTTLE BODY ASSEMBLY) |
![]() |
Disconnect the throttle body assembly connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D4-5 (VC) - D4-3 (E2) | Power switch on (IG) | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Throttle Body Assembly) |
Reconnect the throttle body assembly connector.
|
| ||||
| OK | |
| 3.REPLACE THROTTLE BODY ASSEMBLY |
Replace the throttle body assembly (Click here).
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
With the vehicle stationary, fully depress and release the accelerator pedal.
Idle the engine for 2 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||