Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Power switch ACC signal/ON or OFF
    ON: Power switch on (ACC)
    OFF: Power switch off
    -
    IG SW
    Power switch IG signal/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    RR Door Courtesy SW
    Rear door courtesy light switch RH signal/ON or OFF
    ON: Rear door LH or RH open
    OFF: Rear door LH and RH closed
    -
    RL Door Courtesy SW
    Rear door courtesy light switch LH signal/ON or OFF
    ON: Rear door LH or RH open
    OFF: Rear door LH and RH closed
    -
    Back Door Courtesy SW
    Back door courtesy switch signal/ON or OFF
    ON: Back door open
    OFF: Back door closed
    -
    FR Door Lock Pos
    Front door unlock detection switch RH signal/ON or OFF
    ON: Front door RH unlocked
    OFF: Front door RH locked
    -
    FR Door Courtesy
    Front door courtesy light switch RH signal/ON or OFF
    ON: Front door RH open
    OFF: Front door RH closed
    -
    FL Door Lock Pos
    Front door unlock detection switch LH signal/ON or OFF
    ON: Front door LH unlocked
    OFF: Front door LH locked
    -
    FL Door Courtesy
    Front door courtesy light switch LH signal/ON or OFF
    ON: Front door LH open
    OFF: Front door LH closed
    -
    RR-Door Lock Pos SW
    Rear door unlock detection switch RH signal/ON or OFF
    ON: Rear door LH or RH unlocked
    OFF: Rear door LH and RH locked
    -
    RL-Door Lock Pos SW
    Rear door unlock detection switch LH signal/ON or OFF
    ON: Rear door LH or RH unlocked
    OFF: Rear door LH and RH locked
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body or Smart Key / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Illuminated Entry System
    Interior lights
    ON/OFF
    Interior light door switch on and all doors closed
    Interior Panel Relay
    Interior panel relay
    ON/OFF
    Power switch is off and light control switch in tail position
    Step Light Operation
    Footwell lights
    ON/OFF
    Power switch off

    Smart Key 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power/Engine SW Light
    Power switch illumination
    ON/OFF
    All doors closed