EXHAUST PIPE > INSTALLATION |
| 1. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/ Exhaust Heat Recirculation System) |
![]() |
Using a vernier caliper, measure the free length of the compression springs.
| Minimum | 41.5 mm (1.64 in.) |
Fully insert a new gasket to the exhaust manifold.
![]() |
Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold.
| *1 | Exhaust Manifold |
| *2 | Gasket |
| *3 | Wooden Block |
Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.
![]() |
Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.
![]() |
Connect the 2 heater water hoses.
| 2. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/o Exhaust Heat Recirculation System) |
![]() |
Using a vernier caliper, measure the free length of the compression springs.
| Minimum | 41.5 mm (1.64 in.) |
Fully insert a new gasket to the exhaust manifold.
![]() |
Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold.
| *1 | Exhaust Manifold |
| *2 | Gasket |
| *3 | Wooden Block |
Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.
![]() |
Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.
| 3. INSTALL OXYGEN SENSOR |
![]() |
Using SST, install the heated oxygen sensor onto the front exhaust pipe.
| *1 | Fulcrum Length 300 mm |
| *2 | Fulcrum Length 30 mm |
![]() |
Connect the wire harness to install the wire harness clamp bracket.
![]() |
Install the wire harness clamp bracket with the bolt.
Install the wire harness bracket.
Connect the heated oxygen sensor connector.
| 4. INSTALL FRONT CENTER FLOOR BRACE |
![]() |
Install the front center floor brace with the 4 bolts.
| 5. INSTALL FRONT NO. 3 ENGINE UNDER COVER |
![]() |
Install the front No. 3 engine under cover with the 4 clips.
| 6. INSTALL TAIL EXHAUST PIPE ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the compression springs.
| Minimum | 38.5 mm (1.52 in.) |
Fully insert a new gasket to the front exhaust pipe assembly.
![]() |
Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the front exhaust pipe assembly.
| *1 | Front Exhaust Pipe Assembly |
| *2 | Gasket |
| *3 | Wooden Block |
Connect the tail exhaust pipe assembly to the 2 exhaust pipe supports.
![]() |
Install the tail exhaust pipe assembly with the 2 bolts and 2 compression springs.
| 7. ADD COOLANT (for Engine with Exhaust Heat Recirculation System) |
Tighten the radiator drain cock plug.
Remove the reservoir tank cap.
![]() |
Add coolant to B line of the reservoir tank.
| *1 | B Line |
| Item | Capacity |
| Engine coolant | w/ Exhaust Heat Recirculation System: 7.2 liters (7.6 US qts, 6.3 lmp. qts) |
| w/o Exhaust Heat Recirculation System: 6.5 liters (6.8 US qts, 5.7 lmp. qts) |
Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the reservoir tank cap.
Put the engine in inspection mode (Click here).
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.
![]() |
After the engine has cooled down, check that the coolant level is between full and low.
| *1 | Full Line |
| *2 | Low Line |
| 8. INSPECT FOR COOLANT LEAK (for Engine with Exhaust Heat Recirculation System) |
Remove the reservoir tank cap.
![]() |
Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.
Put the engine in inspection mode (Click here).
Warm up the engine.
Using the reservoir cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump assembly for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
Remove the radiator cap tester.
Install the reservoir tank cap.
| 9. INSPECT FOR EXHAUST GAS LEAK |