Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK POWER SWITCH


  1. Disconnect the L43 power switch connector.


    B146454E17

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L43-8 (AGND) - Body ground
    P - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L43 power switch connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L43-9 (TXCT) - L43-8 (AGND)
    V - P
    Key code output signal
    1. Power switch off
    2. 30 seconds after door opened and closed
    3. Brake pedal not depressed
    Below 1 V
    L43-9 (TXCT) - L43-8 (AGND)
    V - P
    Key code output signal
    1. Power switch off
    2. Key not in cabin
    3. Power switch pressed within 30 seconds
    Pulse generation
    (See waveform 1)
    L43-10 (CODE) - L43-8 (AGND)
    L - P
    Demodulated signal of key code data
    1. Power switch off
    2. 30 seconds after door opened and closed
    3. Brake pedal not depressed
    Below 1 V
    L43-10 (CODE) - L43-8 (AGND)
    L - P
    Demodulated signal of key code data
    1. Power switch off
    2. Key battery removed
    3. Power switch touched with key and pressed
    Pulse generation
    (See waveform 2)
    L43-14 (VC5) - L43-8 (AGND)
    Y - P
    Power supply
    1. Power switch off
    2. 30 seconds after door opened and closed
    3. Brake pedal not depressed
    Below 1 V
    L43-14 (VC5) - L43-8 (AGND)
    Y - P
    Power supply
    1. Power switch off
    2. Key not in cabin
    3. Power switch pressed within 30 seconds
    Pulse generation
    (See waveform 3)
    If the result is not as specified, the power switch may have a malfunction.



  5. Inspect using an oscilloscope.



      B164407E01
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      L43-9 (TXCT) - L43-8 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      1. Power switch off
      2. Key not in cabin
      3. Power switch pressed within 30 seconds



    2. B164408E01
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      L43-10 (CODE) - L43-8 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      1. Power switch off
      2. Key battery removed
      3. Power switch touched with key and pressed



    4. B203497E01
    5. Waveform 3 (Reference)
      Item
      Content
      Tester Connection
      L43-14 (VC5) - L43-8 (AGND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      1. Power switch off
      2. Key not in cabin
      3. Power switch pressed within 30 seconds


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. Disconnect the L62 certification ECU (smart key ECU assembly) connector.


    B203498E16

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L62-1 (+B) - L62-15 (E)
    B - W-B
    +B power supply
    Power switch off
    11 to 14 V
    L62-15 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L62-17 (CUTB) - L62-15 (E)
    Y - W-B
    Dark current cut fuse pin input signal
    Power switch off
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L62 certification ECU (smart key ECU assembly) connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L62-2 (IND) - Body ground
    B - Body ground
    Security indicator light signal
    1. Power switch on (IG)
    2. Security indicator light off
    Below 2 V
    L62-2 (IND) - Body ground
    B - Body ground
    Security indicator light signal
    1. Power switch off
    2. Security indicator light blinks
    Pulse generation
    L62-12 (TXCT) - L62-36 (AGND)
    V - P
    Power switch TXCT output
    1. Power switch off
    2. 30 seconds after door opened and closed
    3. Brake pedal not depressed
    Below 1 V
    L62-12 (TXCT) - L62-36 (AGND)
    V - P
    Power switch TXCT output
    1. Power switch off
    2. Key not in cabin
    3. Power switch pressed within 30 seconds
    Pulse generation (See waveform 1)
    L62-13 (CODE) - L62-36 (AGND)
    L - P
    Power switch CODE input
    1. Power switch off
    2. 30 seconds after door opened and closed
    3. Brake pedal not depressed
    Below 1 V
    L62-13 (CODE) - L62-36 (AGND)
    L - P
    Power switch CODE input
    1. Power switch off
    2. Key battery removed
    3. Power switch touched with key and pressed
    Pulse generation (See waveform 2)
    L62-16 (IG) - L62-15 (E)
    BE - W-B
    IG power supply
    Power switch off
    Below 1 V
    L62-16 (IG) - L62-15 (E)
    BE - W-B
    IG power supply
    Power switch on (IG)
    11 to 14 V
    L62-28 (VC5) - L62-36 (AGND)
    Y - P
    Power switch power supply
    1. Power switch off
    2. 30 seconds after door opened and closed
    3. Brake pedal not depressed
    Below 1 V
    L62-28 (VC5) - L62-36 (AGND)
    Y - P
    Power switch power supply
    1. Power switch off
    2. Key not in cabin
    3. Power switch pressed within 30 seconds
    Pulse generation (See waveform 3)
    L62-34 (EFII) - L62-15 (E)*
    L - W-B
    Power management control ECU (HV CPU) output signal
    Power switch off
    11 to 14 V
    L62-34 (EFII) - L62-15 (E)*
    L - W-B
    Power management control ECU (HV CPU) output signal
    Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected
    Pulse generation (See waveform 4)
    L62-35 (EFIO) - L62-15 (E)*
    R - W-B
    Power management control ECU (HV CPU) input signal
    Power switch off
    Below 1 V
    L62-35 (EFIO) - L62-15 (E)*
    R - W-B
    Power management control ECU (HV CPU) input signal
    Power switch on (IG)
    Pulse generation (See waveform 5)
    L62-36 (AGND) - Body ground
    P - Body ground
    Power switch ground
    Always
    Below 1 Ω

    1. *: w/o Airbag Cut-off Switch
    2. If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.



  5. Inspect using an oscilloscope.



      B164407E01
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      L62-12 (TXCT) - L62-36 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      1. Power switch off
      2. Key not in cabin
      3. Power switch pressed within 30 seconds



    2. B164408E01
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      L62-13 (CODE) - L62-36 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      1. Power switch off
      2. Key battery removed
      3. Power switch touched with key and pressed



    4. B203497E01
    5. Waveform 3 (Reference)
      Item
      Content
      Tester Connection
      L62-28 (VC5) - L62-36 (AGND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      1. Power switch off
      2. Key not in cabin
      3. Power switch pressed within 30 seconds



    6. B229710E01
    7. Waveform 4 (Reference)
      Item
      Content
      Tester Connection
      L62-34 (EFII) - L62-15 (E)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected



    8. B229709E01
    9. Waveform 5 (Reference)
      Item
      Content
      Tester Connection
      L62-35 (EFIO) - L62-15 (E)
      Tool Setting
      5 V/DIV., 50 ms./DIV.
      Condition
      Power switch on (IG)


CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ Airbag Cut-off Switch)


  1. Disconnect the L10 ID code box (immobiliser code ECU) connector.


    B118534E20

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L10-1 (+B) - L10-8 (GND)
    B - W-B
    +B power supply
    Power switch off
    11 to 14 V
    L10-8 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L10 ID code box (immobiliser code ECU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L10-5 (EFII) - L10-8 (GND)
    L - W-B
    Power management control ECU (HV CPU) output signal
    Power switch off
    11 to 14 V
    L10-5 (EFII) - L10-8 (GND)
    L - W-B
    Power management control ECU (HV CPU) output signal
    Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected
    Pulse generation
    (See waveform 1)
    L10-6 (EFIO) - L10-8 (GND)
    R - W-B
    Power management control ECU (HV CPU) input signal
    Power switch off
    Below 1 V
    L10-6 (EFIO) - L10-8 (GND)
    R - W-B
    Power management control ECU (HV CPU) input signal
    Power switch on (IG)
    Pulse generation
    (See waveform 2)

    1. If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.



  5. Inspect using an oscilloscope.



      B229710E01
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      L10-5 (EFII) - L10-8 (GND)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected



    2. B229709E01
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      L10-6 (EFIO) - L10-8 (GND)
      Tool Setting
      5 V/DIV., 50 ms./DIV.
      Condition
      Power switch on (IG)


CHECK TRANSMISSION CONTROL ECU ASSEMBLY


  1. Disconnect the A23 and A24 transmission control ECU assembly connectors.


    B228550E02

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A23-15 (BATT) - Body ground
    SB - Body ground
    Battery power supply
    Power switch off
    11 to 14 V
    A24-1 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    A24-5 (E02) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    A24-6 (E01) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK POWER MANAGEMENT CONTROL ECU (HV CPU)


  1. Disconnect the L5 power management control ECU (HV CPU) connector.


    B219312E02

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L5-6 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L5 power management control ECU (HV CPU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L6-20 (IMO) - L5-6 (E1)
    L - BR
    Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 input signal
    Power switch off
    11 to 14 V
    L6-20 (IMO) - L5-6 (E1)
    L - BR
    Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 input signal
    Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected
    Pulse generation
    (See waveform 1)
    L6-21 (IMI) - L5-6 (E1)
    R - BR
    Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 output signal
    Power switch off
    Below 1 V
    L6-21 (IMI) - L5-6 (E1)
    R - BR
    Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 output signal
    Power switch on (IG)
    Pulse generation
    (See waveform 2)

    1. *1: w/o Airbag Cut-off Switch
    2. *2: w/ Airbag Cut-off Switch
    3. If the result is not as specified, the power management control ECU (HV CPU) may have a malfunction.



  5. Waveform:



      B229710E01
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      L6-20 (IMO) - L5-6 (E1)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected



    2. B229709E01
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      L6-21 (IMI) - L5-6 (E1)
      Tool Setting
      5 V/DIV., 50 ms./DIV.
      Condition
      Power switch on (IG)


COMBINATION METER ASSEMBLY


  1. Disconnect the L27 combination meter assembly connector.


    E165864E02

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L27-18 (B) - Body ground
    R - Body ground
    Battery
    Power switch off
    11 to 14 V
    L27-30 (ES) - Body ground
    BR - Body ground
    Ground (Signal ground)
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L27 combination meter assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L27-19 (IG+) - Body ground
    L - Body ground
    Power switch signal
    Power switch off
    Below 1 V
    L27-19 (IG+) - Body ground
    L - Body ground
    Power switch signal
    Power switch on (IG)
    11 to 14 V
    L27-22 (LP) - Body ground
    B - Body ground
    Security indicator light signal
    1. Power switch on (IG)
    2. Security indicator light off
    Below 2 V
    L27-22 (LP) - Body ground
    B - Body ground
    Security indicator light signal
    1. Power switch off
    2. Security indicator light blinks
    Pulse generation
    If the result is not as specified, the combination meter assembly may have a malfunction.