Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Entry & Start / Data List.

  5. Read the Data List according to the display on the intelligent tester.


Entry & Start (Certification ECU (Smart Key ECU Assembly)) 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Ignition Switch
Power switch on (IG) signal/ON or OFF
ON: Power switch on (IG) or hybrid vehicle control system started
OFF: Power switch off
-
Immobilizer when IG=ON
Immobiliser system status when power switch on (IG)l/UNSET or SET
SET: Power switch off
UNSET: Power switch on (IG) or hybrid vehicle control system started
-
Immobiliser
Immobiliser system status/Set or Unset
Set: Power switch off
Unset: Power switch on (IG) or hybrid vehicle control system started
-
Master Key
Master key code signal/Match or NoMatch
Match: Master key code sent
NoMatch: Unmatched master key code sent
-
Sub Key
Sub-key (master key) code signal/Match or NoMatch
Match: Sub-key (master key) code sent
NoMatch: Unmatched sub-key (master key) code sent
-
BCC Malfunction
Transponder chip signal/OK or NG
OK: Correct data sent
NG: Incorrect data sent
-
Abnormal Status
Transponder chip data/OK or NG
OK: Data OK
NG: Data error
-
Different Encrypt Code
Transponder chip signal/OK or NG
OK: Correct data sent
NG: Incorrect data sent
-
Different Serial Number
Transponder chip signal/OK or NG
OK: Correct data sent
NG: Incorrect data sent
-
Frame Error
Transponder chip signal/OK or NG
OK: Correct data sent
NG: Incorrect data sent
-
Response
Transponder chip signal/OK or NG
OK: Correct data sent
NG: Incorrect data sent
-
Wireless C Code
Wireless C Code/No Regd or Regd
No Regd: Wireless C Code not registered
Regd: Wireless C Code registered
-
ID-BOX Sleep Condition
ID code box (immobiliser code ECU) condition/Yes or No
Yes: ID code box (immobiliser code ECU) in sleep condition
No: ID code box (immobiliser code ECU) not in sleep condition
-
ID-BOX Start Condition
ID code box (immobiliser code ECU) condition/Yes or No
Yes: ID code box (immobiliser code ECU) sends wake up signal
No: ID code box (immobiliser code ECU) not send wake up signal
-
Engine Start Request
ID code box (immobiliser code ECU) start request condition/OK or NG
OK: Start request condition signal received
NG: Start request condition signal not received
-
3bit Code Request
3bit code reception status/OK or NG
OK: 3bit code received
NG: 3bit code not received

S Code Check
S code verification result/OK or NG
OK: Verification confirmed
NG: Verification not confirmed
-
L Code Check
L code verification result/OK or NG
OK: Verification confirmed
NG: Verification not confirmed
-
Unlock Request Receive
Unlock command reception status/OK or NG
OK: Unlock request received
NG: Unlock request not received
-
Lock Request Receive
Lock command reception status/OK or NG
OK: Lock request received
NG: Lock request not received
-
S Code Check (Past)
S code verification result (past)/OK or NG(Past)
OK: Verification confirmed (past)
NG(Past): Verification not confirmed (past)
-
L Code Check (Past)
L code verification result (past)/OK or NG(Past)
OK: Verification confirmed (past)
NG(Past): Verification not confirmed (past)
-
EFI Code Receive
HV code receive (when DTC stored)/OK or NG
OK: HV code received
NG: HV code not received
-
EFI Communication
HV communication/OK or NG
OK: HV communication normal
NG: HV communication abnormal
-
# Codes
Number of trouble codes/Min.: 0 or Max.: 255
Number of DTCs will be displayed
-

ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Entry & Start / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.


Entry & Start (Certification ECU (Smart Key ECU Assembly)) 
Tester Display
Test Part
Control Range
Diagnostic Note
Immobiliser Indicator
Security indicator light
ON or OFF
-