Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1412/12    Ambient Temperature Sensor Circuit

for Preparation Click here


DESCRIPTION

The ambient temperature sensor is installed in front of the condenser. It detects the ambient temperature to control air conditioning AUTO mode. This sensor is connected to the A/C amplifier and detects fluctuations in the ambient temperature. This data is used for controlling the cabin temperature. The sensor sends a signal to the A/C amplifier. The resistance of the ambient temperature sensor changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The A/C amplifier applies voltage (5 V) to the ambient temperature sensor and reads voltage changes as the resistance of the ambient temperature sensor changes.

DTC No.
DTC Detection Condition
Trouble Area
B1412/12
Open or short in ambient temperature sensor circuit
  1. Ambient temperature sensor
  2. Harness or connector between ambient temperature sensor and A/C amplifier
  3. A/C amplifier

WIRING DIAGRAM


E171454E14


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ambient Temp Sensor
    Ambient temperature sensor /
    Min: -23.3°C (-9.94°F)
    Max: 65.95°C (150.71°F)
    Actual ambient temperature displayed
    -

    OK:
    The display is as specified in the Normal Condition column.


    Result:

    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE A/C AMPLIFIER (Click here)
A


2.INSPECT AMBIENT TEMPERATURE SENSOR
  1. Remove the ambient temperature sensor.



    E162241E19
  1. Disconnect the ambient temperature sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-1 (+) - A4-2 (-)
    10°C (50°F)
    3.00 to 3.73 kΩ
    A4-1 (+) - A4-2 (-)
    15°C (59°F)
    2.45 to 2.88 kΩ
    A4-1 (+) - A4-2 (-)
    20°C (68°F)
    1.95 to 2.30 kΩ
    A4-1 (+) - A4-2 (-)
    25°C (77°F)
    1.60 to 1.80 kΩ
    A4-1 (+) - A4-2 (-)
    30°C (86°F)
    1.28 to 1.47 kΩ
    A4-1 (+) - A4-2 (-)
    35°C (95°F)
    1.00 to 1.22 kΩ
    A4-1 (+) - A4-2 (-)
    40°C (104°F)
    0.80 to 1.00 kΩ
    A4-1 (+) - A4-2 (-)
    45°C (113°F)
    0.65 to 0.85 kΩ
    A4-1 (+) - A4-2 (-)
    50°C (122°F)
    0.50 to 0.70 kΩ
    A4-1 (+) - A4-2 (-)
    55°C (131°F)
    0.44 to 0.60 kΩ
    A4-1 (+) - A4-2 (-)
    60°C (140°F)
    0.36 to 0.50 kΩ

    NOTICE:
    1. Hold the sensor only by its connector. Touching the sensor may change the resistance value.
    2. When measuring, the sensor temperature must be the same as the ambient temperature.

    HINT:
    As the temperature increases, the resistance decreases (see the graph).

    Text in Illustration 
    *1
    Component without harness connected
    (Ambient Temperature Sensor)
    *2
    Sensing Portion



NG
REPLACE AMBIENT TEMPERATURE SENSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR - A/C AMPLIFIER)


    E177002E59
  1. Disconnect the A/C amplifier connector.



    E161678E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L17-5 (TAM) - A4-1 (+)
    Always
    Below 1 Ω
    L17-13 (SG-2) - A4-2 (-)
    Always
    Below 1 Ω
    L17-5 (TAM) - Body ground
    Always
    10 kΩ or higher
    L17-13 (SG-2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to A/C Amplifier)
    *2
    Front view of wire harness connector
    (to Ambient Temperature Sensor)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE A/C AMPLIFIER (Click here)