Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body or Master Switch / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door Courtesy SW
    Rear door courtesy light switch signal/ON or OFF
    ON: Rear left side or rear right side door open
    OFF: Rear left side and rear right side door closed
    -
    RL Door Courtesy SW
    Rear door courtesy light switch signal/ON or OFF
    ON: Rear left side or rear right side door open
    OFF: Rear left side and rear right side door closed
    -
    Back Door Courtesy SW
    Back door courtesy switch signal/ON or OFF
    ON: Back door open
    OFF: Back door closed
    -
    Back Door Open
    Back door lock/Permit or Prohibt
    Permit: Back door unlocked
    Prohibt: Back door locked
    -
    Door Key SW-Lock
    Driver door key-linked lock/unlock switch lock signal/ON or OFF
    ON: Driver door key cylinder turned to lock position
    OFF: Driver door key cylinder not turned to lock position
    -
    Door Key SW Unlock
    Driver door key-linked lock/unlock switch unlock signal/ON or OFF
    ON: Driver door key cylinder turned to unlock position
    OFF: Driver door key cylinder not turned to unlock position
    -
    FR Door Lock Pos
    Front right side door lock position switch signal/LOCK or UNLOCK
    LOCK: Front right side door locked
    UNLOCK: Front right side door unlocked
    -
    FR Door Courtesy
    Front right side door courtesy light switch signal/ON or OFF
    ON: Front right side door open
    OFF: Front right side door closed
    -
    FL Door Lock Pos
    Front left side door lock position switch signal/LOCK or UNLOCK
    LOCK: Front left side door locked
    UNLOCK: Front left side door unlocked
    -
    FL Door Courtesy
    Front left side door courtesy light switch signal/ON or OFF
    ON: Front left side door open
    OFF: Front left side door closed
    -
    Back Door Open Handle SW*1
    Back door opener switch signal/ON or OFF
    ON: Back door opener switch pushed
    OFF: Back door opener switch not pushed
    -
    RR-Door Lock Pos SW
    Rear door lock position switch signal/ON or OFF
    ON: Rear left side or rear right side door unlocked
    OFF: Rear left side and rear right side door locked
    -
    RL-Door Lock Pos SW
    Rear door lock position switch signal/ON or OFF
    ON: Rear left side or rear right side door unlocked
    OFF: Rear left side and rear right side door locked
    -

    1. *1: w/o Entry System Back Door Open Function

    Master Switch (Multiplex Network Master Switch Assembly) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock Switch Status
    Driver door control switch lock signal/ON or OFF
    ON: Lock side of driver door control switch pushed
    OFF: Lock side of driver door control switch not pushed
    -
    Door Unlock Switch Status
    Driver door control switch unlock signal/ON or OFF
    ON: Unlock side of driver door control switch pushed
    OFF: Unlock side of driver door control switch not pushed
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Door Lock
    Operate door lock motor
    Unlock/Lock/OFF
    -
    Trunk and Back-Door Open
    Operate back door lock motor
    ON/OFF
    -