Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/o EGR System)

DTC    P0102    Mass or Volume Air Flow Circuit Low Input

DTC    P0103    Mass or Volume Air Flow Circuit High Input

for Preparation Click here


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the amount of air flowing through the throttle valve.
The ECM uses this information to determine the fuel injection time and to provide the appropriate air fuel ratio.
Inside the mass air flow meter sub-assembly, there is a heated platinum wire which is exposed to the flow of intake air by applying a specific electrical current to the wire.
The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant temperature value of the hot wire, current is applied to these components in the mass air flow meter sub-assembly. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:
When either of these DTCs are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A202104E07


DTC No.
DTC Detection Condition
Trouble Area
P0102
Mass air flow meter voltage less than 0.2 V for 3 seconds
(1 trip detection logic)
  1. Open or short in mass air flow meter sub-assembly circuit
  2. Mass air flow meter sub-assembly
  3. ECM
P0103
Mass air flow meter voltage more than 4.9 V for 3 seconds
(1 trip detection logic)
  1. Open or short in mass air flow meter sub-assembly circuit
  2. Mass air flow meter sub-assembly
  3. ECM

HINT:
When any of these DTCs are stored, check the air-flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Mass Air Flow Rate (gm/sec)
Malfunction
Approximately 0.0
  1. Open in mass air flow meter sub-assembly power source circuit
  2. Open or short in VG circuit
271.0 or more
Open in E2G circuit


WIRING DIAGRAM


A231666E07


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ DTC OUTPUT (DTC P0102 OR P0103)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0102 is output
    A
    DTC P0103 is output
    B



B
Go to step 5
A


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)
A194097E77
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D5-3 (+B) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Mass Air Flow Meter Sub-assembly)

  1. Reconnect the mass air flow meter sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - MASS AIR FLOW METER SUB-ASSEMBLY)
OK


3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D5-5 (VG) - D28-94 (VG)
    Always
    Below 1 Ω
    D5-4 (E2G) - D28-117 (E2G)


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D5-5 (VG) or D28-94 (VG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter sub-assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
OK


4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
  1. Inspect the mass air flow meter sub-assembly, referring to the On-vehicle Inspection for Mass Air Flow Meter (Click here).

  1. Inspect the mass air flow meter sub-assembly, referring to the Inspection for Mass Air Flow Meter (Click here).

  1. Inspect the function of the mass air flow meter sub-assembly.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the tester on.

    4. Put the engine in inspection mode (maintenance mode) (Click here).

    5. Start the engine.

    6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

    7. Check that the MAF value changes when the engine is raced.

      OK:
      The reading changes.



NG
REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D5-4 (E2G) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the mass air flow meter sub-assembly connector.



NG
Go to step 6
OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)  

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D5-4 (E2G) - D28-117 (E2G)
    Always
    Below 1 Ω

  1. Reconnect the mass air flow meter sub-assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
OK

REPLACE ECM (Click here)