Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY

KNEE AIRBAG ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY
  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B226999
  1. Connect the airbag connector and install the clamp to the driver side knee airbag assembly.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

  1. Push in the lock to install the airbag connector.



    B226997
  1. Temporarily install the driver side knee airbag assembly with the 6 claws and 4 guides.



    B226996
  1. Install the driver side knee airbag assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Confirm that the driver side knee airbag assembly is installed securely without any excessive gaps and is not protruding outward.



2. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
  1. Connect each connector.

  1. Engage the clamp.

  1. Engage the 2 guides and claw to connect the hood lock control cable.



    B298864
  1. Engage the 6 claws and clip.

  1. Install the lower instrument panel finish panel assembly with the screw <C>.



3. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)
  1. Connect each connector.

  1. Engage the guide and claw.

  1. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <D>.



4. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
  1. Connect each connector.

  1. Engage the guide and 2 claws.

  1. Install the No. 1 instrument panel under cover sub-assembly with the screw <D>.



5. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B227764
  1. Engage the 2 clips.

  1. Install the cowl side trim board LH with the clip.



6. INSTALL FRONT DOOR SCUFF PLATE LH


    B227761
  1. Engage the 10 claws to install the front door scuff plate LH.



7. INSTALL NO. 1 SWITCH HOLE BASE
  1. Connect the connector.

  1. Engage the 5 claws to install the No. 1 switch hole base.



8. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
  1. Temporarily install the console box assembly.



    B279576
  1. Engage the 9 claws as shown in the illustration.



    B223654
  1. Install the to install the upper instrument panel finish panel assembly with the 2 bolts <A>.

  1. Engage the clamp.



9. INSTALL CONSOLE BOX ASSEMBLY
  1. Connect each connector.



    B279577
  1. Engage the 4 guides and 2 claws as shown in the illustration.

  1. Install the console box assembly with the bolt <B> and 2 clips.



10. INSTALL BOX BOTTOM MAT
  1. Engage the fastener to install the box bottom mat.



11. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    B223646E01
  1. Engage the guide and 4 claws to install the front No. 2 console box insert as shown in the illustration.



12. INSTALL FRONT NO. 1 CONSOLE BOX INSERT


    B223644E01
  1. Engage the guide and 4 claws to install the front No. 1 console box insert as shown in the illustration.



13. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET
  1. Install the No. 2 console box mounting bracket with the 6 bolts <B>.



14. INSTALL ELECTRICAL KEY OSCILLATOR


    B229283
  1. Engage the clamp and install the electrical key oscillator.

    NOTICE:
    Be careful when installing the electrical key oscillator. If the oscillator is dropped, replace it with a new one.

  1. Connect the connector.



15. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY


    C209262
  1. Install the shift lock control unit assembly with the 3 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Connect the connector to the shift lock control unit assembly.



16. INSTALL AIR CONDITIONING CONTROL ASSEMBLY
  1. Connect the connector.

    NOTICE:
    Since the connectors for the air conditioning control assembly and the integration control and panel sub-assembly are the same shape, take care to connect each connector to the correct component.



    E189054
  1. Engage the 4 claws to install the air conditioning control assembly.



17. INSTALL GLOVE COMPARTMENT DOOR
  1. Open the glove compartment door assembly.



    B223486
  1. Insert the glove compartment door as shown in the illustration.

  1. Engage the 7 claws to install the glove compartment door.



18. INSTALL NO. 2 INSTRUMENT PANEL REGISTER


    B223484
  1. Engage the 3 claws and clip to install the No. 2 instrument panel register.



19. INSTALL NO. 1 SIDE DEFROSTER NOZZLE


    B223481
  1. Engage the 3 claws to install the No. 1 side defroster nozzle.



20. INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    B223593
  1. Install the radio tuner opening cover with bracket with the 4 bolts <B>.



21. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver)


    B227341
  1. Engage the 4 claws to install the center instrument cluster finish panel sub-assembly.



22. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)
  1. Connect each connector.

  1. Engage the 4 claws.

  1. Install the radio and display receiver assembly with bracket with the 4 bolts.



23. INSTALL NAVIGATION RECEIVER WITH BRACKET (for Navigation Receiver Type)


    E188508
  1. Engage the 4 claws and temporarily install the navigation receiver with bracket as shown in the illustration.

  1. Install the navigation receiver with bracket with the 4 bolts.



24. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B223459
  1. Connect the connector.

  1. Engage the 3 claws to install the upper instrument panel finish panel sub-assembly.



25. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Connect the connector.

  1. Engage the 14 claws to install the instrument cluster finish panel garnish.



26. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B223456
  1. Engage the 7 claws and 2 clips to install the lower center instrument cluster finish panel sub-assembly.



27. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


    B223453
  1. Connect each connector.

  1. Engage the 6 claws to install the integration control and panel assembly.



28. INSTALL REAR CONSOLE BOX ASSEMBLY

HINT:
Refer to the procedure from Install Rear Console Box Assembly (Click here).



29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



30. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



31. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



32. INSTALL REAR NO. 2 FLOOR BOARD


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.



33. PERFORM DIAGNOSTIC SYSTEM CHECK
  1. Perform a diagnostic system check (Click here).



34. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).