Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > CUSTOMIZE PARAMETERS


NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

HINT:
The following items can be customized.


POWER DOOR LOCK CONTROL SYSTEM

Illuminated Entry 
Display
Default
Content
Setting
Lighting Time
15 s
Function that changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC) or (IG).)
7.5 s, 15 s or 30 s

WIRELESS DOOR LOCK CONTROL SYSTEM

Wireless Door Lock Control System 
Display (item)
Default
Function
Setting
Wireless Control
ON
Function that turns wireless door lock function on or off
ON or OFF
Hazard Answer Back
ON
When the doors are locked by wireless operation, the hazard warning lights flash once.
When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
ON or OFF
Open Door Warning
ON
The buzzer sounds when lock is pressed when any of the doors are ajar.
ON or OFF
Panic Function*1
ON
Function to operate theft deterrent system by continuously pressing panic switch on transmitter for 0.8 seconds
ON or OFF
Auto Lock Time
30 s
Function that regulates the interval between unlocking and automatic relocking of doors
30 s, 60 s or 120 s
Wireless Buzzer Resp*2
ON
Wireless door lock buzzer response
ON or OFF
Wireless Buzzer Vol
Level7
Wireless door lock buzzer volume
Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0
  1. *1: w/ Panic Function
  2. *2: for Australia

Illuminated Entry 
Display
Default
Content
Setting
Lighting Time
15 s
Changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC or IG).)
7.5 s, 15 s or 30 s

ENTRY AND START SYSTEM (for Entry Function)

Entry & Start 
Tester Display
Default
Content
Setting
Park Wait Time
2.5 s
Function that sets waiting time to permit opening door after door is locked with entry lock function
0.5 s, 1.5 s, 2.5 s or 5 s
Ignition Available Area
All
Function that switches the entry hybrid vehicle control system start detection area
Front or All
Back Door Opening Operation*
Long
Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch)
Long, Twice or OFF
  1. *: w/ Entry System Back Door Open Function

Warning 
Tester Display
Default
Content
Setting
Key Low Battery Warning
ON
Function that warns driver that the key battery is weak
ON or OFF

ELECTRICAL KEY CANCEL (ENTRY AND START SYSTEM (for Entry Function))
The electrical key cancel operation disables the following functions:
  1. Entry Unlock/Lock
  2. Entry Hybrid Vehicle Control System Start
  3. Entry System Back Door Open Function*
    *: w/ Entry System Back Door Open Function
  4. Electrical Key Lock-in Prevention
  5. Warning
  1. The operation procedure is as follows:
    Precondition:
    Power switch off, driver door closed and unlocked.

    1. Push the unlock switch of the key once.

    2. Open the driver door within 5 seconds.

    3. Push the unlock switch of the key twice within 5 seconds.

    4. Close and open the driver door twice within 30 seconds.
      (Driver door: Close → Open → Close → Open)

    5. Push the unlock switch of the key twice within 5 seconds.

    6. Close and open the driver door within 30 seconds.
      (Driver door: Close → Open)

    7. Close the driver door within 5 seconds.
      When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
      To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.


ENTRY AND START SYSTEM (for Start Function)

Entry & Start 
Tester Display
Default
Content
Setting
Ignition Available Area (Entry ignition available area)
All
Function to choose the available area for electrical key to start the hybrid control system.
Front or All

CUSTOMIZING FUNCTION WITHOUT INTELLIGENT TESTER (ENTRY AND START SYSTEM (for Start Function))
Performing the following procedure disables the entry and start system.

HINT:
To start the hybrid control system while the entry and start system is disabled, follow the procedure for when the key battery is low (Click here).

  1. The operation procedure is as follows:
    Precondition:
    Power switch off, driver door closed and unlocked.

    1. Push the unlock switch of the key once.

    2. Open the driver door within 5 seconds.

    3. Push the unlock switch of the key twice within 5 seconds.

    4. Close and open the driver door twice within 30 seconds.
      (Driver door: Close → Open → Close → Open)

    5. Push the unlock switch of the key twice within 5 seconds.

    6. Close and open the driver door within 30 seconds.
      (Driver door: Close → Open)

    7. Close the driver door within 5 seconds.
      When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
      To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.


THEFT DETERRENT SYSTEM

Theft Deterrent System 
Display(Item)
Default
Content
Setting
Mech. Key Entry Alarm Cancel
OFF
Function that makes it possible to cancel the alarm with an unlock operation using the mechanical key.
ON / OFF

LIGHTING SYSTEM (LIGHTING INT)

Illuminated Entry 
Tester Display
Default
Content
Setting
Lighting Time
15 s
Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).)
7.5 s, 15 s or 30 s
I/L when ACC OFF
ON
Lights up power switch illumination, front interior lights, rear interior light and footwell lights when the power switch is turned from on (ACC or IG) to off.
ON or OFF
I/L ON W/Door Key Unlock
ON
Lights up power switch illumination, front interior lights, rear interior light and footwell lights when doors are unlocked using a mechanical key or door control transmitter.
ON or OFF
Light Control
ON
Dims (ON setting) or turns off (OFF setting) the footwell lights under the following conditions:
Power switch on (IG), shift lever not in P, and all doors closed.
ON or OFF
Room Light when Aprchd
ON
Lights up the power switch illumination, front interior lights, rear interior light and footwell lights when a key enters any actuation area around the doors.
ON or OFF
Inside Foot Light
ON
ON/OFF of footwell light control function.
ON or OFF

METER / GAUGE SYSTEM

Warning 
Tester Display
Default
Content
Setting
Key Remind Sound
Slow
Function to change the cycle of the key reminder buzzer
Normal, Fast or Slow
Driver Side Seatbelt Warning Buzzer*1
ON
Function to turn on/off the seat belt warning buzzer
ON or OFF
Front Passenger Side Seatbelt Warning Buzzer*1
ON
Function to turn on/off the seat belt warning buzzer
ON or OFF
Rear Seatbelt Warning Buzzer*2
ON
Function to turn on/off the rear seat belt warning buzzer
ON or OFF
Reverse Buzzer
Continual
Function to change the type of the reverse warning buzzer
Single or Continual
  1. *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more.
  2. *2: w/ Rear Seat Belt Warning

SEAT BELT WARNING SYSTEM

Combination Meter 
Tester Display
Default
Content
Setting
Driver Side Seatbelt Warning Buzzer
ON
Function to sound the seat belt warning buzzer
ON / OFF
Front Passenger Side Seatbelt Warning Buzzer
ON
Function to sound the seat belt warning buzzer
ON / OFF
Rear Seat Belt Warning Buzzer*
ON
Function to sound the seat belt warning buzzer
ON / OFF
  1. *: w/ Rear Seat Belt Warning

AIR CONDITIONING SYSTEM

Air Conditioner 
Display (Item)
Default
Content
Setting
Set Temperature Shift
Normal
Function to control with the shifted temperature against the displayed temperature.
+2 C, +1 C, Normal, -1 C or -2 C
Compressor Mode
Automatic
Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off.
Manual or Automatic
Air Inlet Mode
Automatic
Function to shift from INLET mode to RECIRCULATION mode when the A/C is turned on.
Manual or Automatic
Foot/DEF Auto Mode
ON
Function to automatically turn the airflow from FOOT/DEF on when AUTO mode is on.
OFF or ON
Foot/DEF Automatic Blow Up Function
ON
Function to automatically increase the blower level when the defroster is on.
OFF or ON
Ambient Temperature Shift
Normal
Function to control the shifted ambient temperature in relation to the displayed ambient temperature.
+3 C, +2 C, +1 C, Normal, -1 C, -2 C or -3 C
ECO MODE Cancel
OFF
Function to cancel the ECO mode drive when item is on.
OFF or ON
Noise and Vibration Reduction
OFF
Function to change speed of the compressor when item is on.
OFF or ON
Start Pre A/C*1
Long1
Function to set the activation operation method for the remote air conditioning system using the key (electrical transmitter).
1 tim ON, 2 tim ON, Long1 or Long2
Stop Pre A/C*1
2 tim ON
Function to set the stop operation method for the remote air conditioning system using the key (electrical transmitter).
1 tim ON, 2 tim ON, Long1 or Long2
  1. *1: w/ Remote Air Conditioning System

LIGHTING SYSTEM (LIGHTING EXT)

Light Control 
Display
Default
Content
Setting
Disp Ex ON Sen
Normal
Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.
Light2, Light1, Normal, Dark1 or Dark2
Disp Ex OFF Sen
Normal
Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.
Light2, Light1, Normal, Dark1 or Dark2
Response Time
0.1 s
Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position
0.1 s or 1.0 s
Sensitivity
Normal
Adjusts the sensitivity of the automatic light control system.
Light2, Light1, Normal, Dark1 or Dark2
DRL Function
On
ON/OFF of the DRL function
On or Off