Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > CUSTOMIZE PARAMETERS


NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

HINT:
The following items can be customized.


POWER DOOR LOCK CONTROL SYSTEM
  1. Customizing with the intelligent tester

    Illuminated Entry 
    Display
    Default
    Content
    Setting
    Lighting Time
    15 s
    Function that changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC) or (IG).)
    7.5 s, 15 s or 30 s

  2. Customizing function with multi-display (w/ Navigation System)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Light Settings

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Interior Lights Off Timer
      15 sec.
      Function that changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC) or (IG).)
      Off, 7.5 sec., 15 sec. or 30 sec.
      Main body ECU (Multiplex network body ECU)


WIRELESS DOOR LOCK CONTROL SYSTEM
  1. Customizing with the intelligent tester

    Wireless Door Lock Control System 
    Display (item)
    Default
    Function
    Setting
    Wireless Control
    ON
    Function that turns wireless door lock function on or off
    ON or OFF
    Hazard Answer Back
    ON
    When the doors are locked by wireless operation, the hazard warning lights flash once.
    When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
    ON or OFF
    Open Door Warning
    ON
    The buzzer sounds when lock is pressed when any of the doors are ajar.
    ON or OFF
    Panic Function*1
    ON
    Function to operate theft deterrent system by continuously pressing panic switch on transmitter for 0.8 seconds
    ON or OFF
    Auto Lock Time
    30 s
    Function that regulates the interval between unlocking and automatic relocking of doors
    30 s, 60 s or 120 s
    Wireless Buzzer Resp*2
    ON
    Wireless door lock buzzer response
    ON or OFF
    Wireless Buzzer Vol
    Level7
    Wireless door lock buzzer volume
    Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0

    1. *1: w/ Panic Function
    2. *2: for Australia

    Illuminated Entry 
    Display
    Default
    Content
    Setting
    Lighting Time
    15 s
    Changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC or IG).)
    7.5 s, 15 s or 30 s

  2. Customizing with the multi-display (for Navigation Receiver Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Auto Relock Timer
      30 s
      Function that regulates the interval between unlocking and automatic relocking of doors
      30 s, 60 s or 120 s
      Main body ECU (Multiplex network body ECU)
      Lock/Unlock Feedback-Lights
      On
      When the doors are locked by wireless operation, the hazard warning lights flash once.
      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock/Unlock Feedback-Tone
      7
      Wireless door lock buzzer volume
      Off, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)

    4. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Light Settings

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Interior Lights Off Timer
      15 sec.
      Changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC or IG).)
      Off, 7.5 sec., 15 sec. or 30 sec.
      Main body ECU (Multiplex network body ECU)

  3. Customizing with the multi-display (for Radio and Display Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Lock Feedback Volume
      7
      Wireless door lock buzzer volume
      Off, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)


ENTRY AND START SYSTEM (for Entry Function)
  1. Customizing with the intelligent tester

    Entry & Start 
    Tester Display
    Default
    Content
    Setting
    Park Wait Time
    2.5 s
    Function that sets waiting time to permit opening door after door is locked with entry lock function
    0.5 s, 1.5 s, 2.5 s or 5 s
    Ignition Available Area
    All
    Function that switches the entry hybrid vehicle control system start detection area
    Front or All
    Back Door Opening Operation*
    Long
    Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch)
    Long, Twice or OFF
    *: w/ Entry System Back Door Open Function

    Warning 
    Tester Display
    Default
    Content
    Setting
    Key Low Battery Warning
    ON
    Function that warns driver that the key battery is weak
    ON or OFF

  2. Customizing with the multi-display (for Radio and Display Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Entry and start system
      On
      Function that enables or disables the smart key system.
      On or Off
      Certification ECU (smart key ECU assembly)

  3. Customizing with the multi-display (for Navigation Receiver Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Entry and start system
      On
      Function that enables or disables the smart key system.
      On or Off
      Certification ECU (smart key ECU assembly)


ELECTRICAL KEY CANCEL (ENTRY AND START SYSTEM (for Entry Function))
The electrical key cancel operation disables the following functions:
  1. Entry Unlock/Lock
  2. Entry Hybrid Vehicle Control System Start
  3. Entry System Back Door Open Function*
    *: w/ Entry System Back Door Open Function
  4. Electrical Key Lock-in Prevention
  5. Warning
  1. The operation procedure is as follows:
    Precondition:
    Power switch off, driver door closed and unlocked.

    1. Push the unlock switch of the key once.

    2. Open the driver door within 5 seconds.

    3. Push the unlock switch of the key twice within 5 seconds.

    4. Close and open the driver door twice within 30 seconds.
      (Driver door: Close → Open → Close → Open)

    5. Push the unlock switch of the key twice within 5 seconds.

    6. Close and open the driver door within 30 seconds.
      (Driver door: Close → Open)

    7. Close the driver door within 5 seconds.
      When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
      To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.


ENTRY AND START SYSTEM (for Start Function)
  1. Customizing with the intelligent tester

    Entry & Start 
    Tester Display
    Default
    Content
    Setting
    Ignition Available Area (Entry ignition available area)
    All
    Function to choose the available area for electrical key to start the hybrid control system.
    Front or All

  2. Customizing with the multi-display (for Radio and Display Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Entry and Start System
      On
      Function that enables or disables the entry and start system.
      On or Off
      Certification ECU (smart key ECU assembly)

  3. Customizing with the multi-display (for Navigation Receiver Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Entry and Start System
      On
      Function that enables or disables the entry and start system.
      On or Off
      Certification ECU (smart key ECU assembly)


CUSTOMIZING FUNCTION WITHOUT INTELLIGENT TESTER (ENTRY AND START SYSTEM (for Start Function))
Performing the following procedure disables the entry and start system.

HINT:
To start the hybrid control system while the entry and start system is disabled, follow the procedure for when the key battery is low (Click here).

  1. The operation procedure is as follows:
    Precondition:
    Power switch off, driver door closed and unlocked.

    1. Push the unlock switch of the key once.

    2. Open the driver door within 5 seconds.

    3. Push the unlock switch of the key twice within 5 seconds.

    4. Close and open the driver door twice within 30 seconds.
      (Driver door: Close → Open → Close → Open)

    5. Push the unlock switch of the key twice within 5 seconds.

    6. Close and open the driver door within 30 seconds.
      (Driver door: Close → Open)

    7. Close the driver door within 5 seconds.
      When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
      To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.


THEFT DETERRENT SYSTEM

Theft Deterrent System 
Display(Item)
Default
Content
Setting
Mech. Key Entry Alarm Cancel
OFF
Function that makes it possible to cancel the alarm with an unlock operation using the mechanical key.
ON / OFF

LIGHTING SYSTEM (LIGHTING INT)
  1. Customizing with the intelligent tester

    Illuminated Entry 
    Tester Display
    Default
    Content
    Setting
    Relevant ECU
    Lighting Time
    15 s
    Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).)
    7.5 s, 15 s or 30 s
    Main body ECU (Multiplex network body ECU)
    I/L when ACC OFF
    ON
    Lights up power switch illumination, front interior lights, rear interior light and footwell lights when the power switch is turned from on (ACC or IG) to off.
    ON or OFF
    I/L ON W/Door Key Unlock
    ON
    Lights up power switch illumination, front interior lights, rear interior light and footwell lights when doors are unlocked using a mechanical key or door control transmitter.
    ON or OFF
    Light Control
    ON
    Dims (ON setting) or turns off (OFF setting) the footwell lights under the following conditions:
    Power switch on (IG), shift lever not in P, and all doors closed.
    ON or OFF
    Room Light when Aprchd
    ON
    Lights up the power switch illumination, front interior lights, rear interior light and footwell lights when a key enters any actuation area around the doors.
    ON or OFF
    Inside Foot Light
    ON
    ON/OFF of footwell light control function.
    ON or OFF

  2. Customizing with the multi-display (for Navigation Receiver Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: Setup / Vehicle / Vehicle Customization / Light Settings.

    3. Select the setting by referring to the table below:

      Light Settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Interior Lights Off Timer
      15 sec.
      Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or ON).)
      Off, 7.5 sec., 15 sec., or 30 sec.
      Main body ECU (Multiplex network body ECU)


METER / GAUGE SYSTEM

Warning 
Tester Display
Default
Content
Setting
Key Remind Sound
Slow
Function to change the cycle of the key reminder buzzer
Normal, Fast or Slow
Driver Side Seatbelt Warning Buzzer*1
ON
Function to turn on/off the seat belt warning buzzer
ON or OFF
Front Passenger Side Seatbelt Warning Buzzer*1
ON
Function to turn on/off the seat belt warning buzzer
ON or OFF
Rear Seatbelt Warning Buzzer*2
ON
Function to turn on/off the rear seat belt warning buzzer
ON or OFF
Reverse Buzzer
Continual
Function to change the type of the reverse warning buzzer
Single or Continual
  1. *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more.
  2. *2: w/ Rear Seat Belt Warning

SEAT BELT WARNING SYSTEM

Combination Meter 
Tester Display
Default
Content
Setting
Driver Side Seatbelt Warning Buzzer
ON
Function to sound the seat belt warning buzzer
ON / OFF
Front Passenger Side Seatbelt Warning Buzzer
ON
Function to sound the seat belt warning buzzer
ON / OFF
Rear Seat Belt Warning Buzzer*
ON
Function to sound the seat belt warning buzzer
ON / OFF
  1. *: w/ Rear Seat Belt Warning

AIR CONDITIONING SYSTEM
  1. Customizing with the intelligent tester

    Air Conditioner 
    Display (Item)
    Default
    Content
    Setting
    Set Temperature Shift
    Normal
    Function to control the shifted temperature against the displayed temperature.
    -2C, -1C, Normal, +1C, +2C
    Air inlet Mode
    Automatic
    In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode
    Automatic or Manual
    Foot/DEF Auto Mode
    ON
    Function to automatically turn the airflow from FOOT/DEF on when AUTO mode is on.
    ON or OFF
    Foot/DEF Automatic Blow Up Function
    ON
    Function to automatically increase the blower level when the defroster is on.
    ON or OFF
    Ambient Temperature Shift
    Normal
    Function to control the shifted ambient temperature in relation to the displayed ambient temperature.
    -3C, -2C, -1C, Normal, +1C, +2C, +3C
    ECO MODE Cancel
    OFF
    Function to cancel the ECO drive mode when item is on.
    OFF or ON
    Noise and Vibration Reduction
    OFF
    Function to change speed of the compressor when item is on.
    OFF or ON
    Start Pre A/C*1
    Long1
    Function to set the activation operation method for the remote air conditioning system using the key (electrical transmitter).
    1 tim ON, 2 tim ON, Long1 or Long2
    Stop Pre A/C*1
    2 tim ON
    Function to set the stop operation method for the remote air conditioning system using the key (electrical transmitter).
    1 tim ON, 2 tim ON, Long1 or Long2

    1. *1: w/ Remote Air Conditioning System

  2. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle settings / Climate settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Efficient Ventilation Mode
      On
      In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode
      On or Off
      Air conditioning amplifier assembly


POWER WINDOW CONTROL SYSTEM
  1. Customizing with the intelligent tester

    Power Window 
    Tester Display
    Default
    Content
    Setting
    Relevant ECU
    P Window Auto Up
    Avail
    This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly (for front passenger door).
    Not Avl/Avail
    Power window ECU (Power window regulator motor assembly)
    P Window Auto Up From Driver
    Avail
    This function is used to enable or disable the remote auto up function for the front passenger door window using the multiplex network master switch assembly.
    Not Avl/Avail
    Power window ECU (Power window regulator motor assembly)
    RR Window Auto Up
    Avail
    This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear RH door).
    Not Avl/Avail
    Power window ECU (Power window regulator motor assembly)
    RR Window Auto Up From Driver
    Avail
    This function is used to enable or disable the remote auto up function for the rear RH door window using the multiplex network master switch assembly.
    Not Avl/Avail
    Power window ECU (Power window regulator motor assembly)
    RL Window Auto Up
    Avail
    This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear LH door).
    Not Avl/Avail
    Power window ECU (Power window regulator motor assembly)
    RL Window Auto Up From Driver
    Avail
    This function is used to enable or disable the remote auto up function for the rear LH door window using the multiplex network master switch assembly.
    Not Avl/Avail
    Power window ECU (Power window regulator motor assembly)


LIGHTING SYSTEM (LIGHTING EXT)
  1. Customizing with the intelligent tester

    Light Control 
    Display
    Default
    Content
    Setting
    Relevant ECU
    Disp Ex ON Sen
    Normal
    Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*A
    Light2, Light1, Normal, Dark1 or Dark2
    Main Body ECU (Multiplex Network Body ECU)
    Disp Ex OFF Sen
    Normal
    Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*B
    Light2, Light1, Normal, Dark1 or Dark2
    Response Time
    0.1 s
    Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position
    0.1 s or 1.0 s
    Sensitivity
    Normal
    Adjusts the sensitivity of the automatic light control system.*C
    Light2, Light1, Normal, Dark1 or Dark2
    DRL Function
    On
    ON/OFF of the DRL function
    On or Off

    HINT:
    The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


    *A 
    Brightness level required to dim the lights

    E107164

    Setting
    Dark2
    Dark1
    Normal
    Light1
    Light2

    *B 
    Brightness level required to cancel the dimming of the lights

    E107164

    Setting
    Dark2
    Dark1
    Normal
    Light1
    Light2

    *C 
    Sensitivity of the automatic light control system

    E107164

    Setting
    Dark2
    Dark1
    Normal
    Light1
    Light2

  2. Customizing with the multi-display (for Navigation Receiver Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Light Settings.

    3. Select the setting by referring to the table below.

      Light Settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Headlamps-On Sensitivity
      0
      Adjusts the sensitivity of the automatic light control system.*A
      -2, -1, 0, +1 or +2
      Main Body ECU (Multiplex Network Body ECU)

      HINT:
      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


      *A 
      Sensitivity of the automatic light control system

      E107164

      Setting
      -2
      -1
      0
      +1
      +2

  3. Customizing with the multi-display (for Radio and Display Type)

    1. Turn the power switch on (IG).

    2. Enter the following menus: SETUP / Vehicle.

    3. Select the setting by referring to the table below.

      Vehicle Settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Light Sensor Sensitivity
      0
      Adjusts the sensitivity of the automatic light control system.*A
      -2, -1, 0, +1 or +2
      Main Body ECU (Multiplex Network Body ECU)

      HINT:
      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


      *A 
      Sensitivity of the automatic light control system

      E107164

      Setting
      -2
      -1
      0
      +1
      +2