Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM

DYNAMIC RADAR CRUISE CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK DRIVING SUPPORT ECU

E184662E10


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
L60-6 (SPSW) - L60-25 (GND)
R - W-B
Steering pad switch signal
(distance control signal)
Power switch on (IG)
Distance control switch off
10 to 14 V
L60-6 (SPSW) - L60-25 (GND)
R - W-B
Steering pad switch signal
(distance control signal)
Power switch on (IG)
Distance control switch on
6 to 7 V
L60-10 (CCHG) - L60-25 (GND)
G - W-B
Cruise control main switch signal
Power switch on (IG),
MODE switch off
10 to 14 V
L60-10 (CCHG) - L60-25 (GND)
G - W-B
Cruise control main switch signal
Power switch on (IG),
MODE switch on
Below 1 V
L60-17 (CA2L) - L60-25 (GND)
W - W-B
CAN communication signal
Power switch on (IG)
Pulse generation
(See waveform 1)
L60-18 (CA1N) - L60-25 (GND)
L - W-B
CAN communication signal
Power switch on (IG)
Pulse generation
(See waveform 2)
L60-23 (CCS) - L60-25 (GND)
V - W-B
Cruise control main switch signal
Power switch on (IG)
10 to 14 V
L60-23 (CCS) - L60-25 (GND)
V - W-B
Cruise control main switch signal
Power switch on (IG),
CANCEL switch on
6.6 to 10.1 V
L60-23 (CCS) - L60-25 (GND)
V - W-B
Cruise control main switch signal
Power switch on (IG),
-SET switch on
4.5 to 7.1 V
L60-23 (CCS) - L60-25 (GND)
V - W-B
Cruise control main switch signal
Power switch on (IG),
+RES switch on
2.3 to 4.0 V
L60-23 (CCS) - L60-25 (GND)
V - W-B
Cruise control main switch signal
Power switch on (IG),
Main switch on
Below 1 V
L60-25 (GND) - Body ground
W-B - Body ground
Earth (ground circuit of driving support ECU)
Always
Below 1 Ω
L60-27 (STP-) - L60-25 (GND)
Y - W-B
Stop light signal
Brake pedal released
Below 1 V
L60-27 (STP-) - L60-25 (GND)
Y - W-B
Stop light signal
Brake pedal depressed
7.5 to 14 V
L60-28 (ST1-) - L60-25 (GND)
R - W-B
Stop light signal
Power switch on (IG),
Brake pedal released
7.5 to 14 V
L60-28 (ST1-) - L60-25 (GND)
R - W-B
Stop light signal
Power switch on (IG),
Brake pedal depressed
Below 1 V
L60-30 (B) - L60-25 (GND)
B - W-B
Power source
Power switch on (IG)
11 to 14 V
L60-32 (WIP2) - L60-25 (GND)
P - W-B
Wiper switch signal
Power switch on (IG),
Wiper switch off
Below 1 V
L60-32 (WIP2) - L60-25 (GND)
P - W-B
Wiper switch signal
Power switch on (IG),
Wiper switch LO position
6 to 7 V
L60-32 (WIP2) - L60-25 (GND)
P - W-B
Wiper switch signal
Power switch on (IG),
Wiper switch HI position
11 to 14 V
L60-39 (CA2H) - L60-25 (GND)
B - W-B
CAN communication signal
Power switch on (IG)
Pulse generation
(See waveform 3)
L60-40 (CA1P) - L60-25 (GND)
Y - W-B
CAN communication signal
Power switch on (IG)
Pulse generation
(See waveform 4)


    A086155E19
  1. WAVEFORM 1

    1. CAN communication signal
      Driving support ECU Terminal Name
      Between CA2L and GND
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)

      HINT:
      The waveform varies depending on the CAN communication signal.



  2. A086154E17
  3. WAVEFORM 2

    1. CAN communication signal
      Driving support ECU Terminal Name
      Between CA1N and GND
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)



  4. A086154E17
  5. WAVEFORM 3

    1. CAN communication signal
      Driving support ECU Terminal Name
      Between CA2H and GND
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)

      HINT:
      The waveform varies depending on the CAN communication signal.



  6. A086155E19
  7. WAVEFORM 4

    1. CAN communication signal
      Driving support ECU Terminal Name
      Between CA1P and GND
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)


CHECK POWER MANAGEMENT CONTROL ECU

E186873E04


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
L5-6 (E1) - Body ground
BR - Body ground
Earth (ground) circuit of power management control ECU
Always
Below 1 Ω
L5-11 (TC) - L5-6 (E1)
P - BR
Terminal TC of DLC3
Power switch on (IG)
11 to 14 V
L5-11 (TC) - L5-6 (E1)
P - BR
Terminal TC of DLC3
Terminals TC and CG of DLC3 connected
Below 1 V
L5-34 (CA2H) - L5-6 (E1)
P - BR
CAN communication line
Power switch on (IG)
Pulse generation
(see waveform 1)
L5-35 (CA2L) - L5-6 (E1)
V - BR
CAN communication line
Power switch on (IG)
Pulse generation
(see waveform 2)
L6-24 (CA1L) - L5-6 (E1)
W - BR
CAN communication line
Power switch on (IG)
Pulse generation
(see waveform 2)
L6-25 (CA1H) - L5-6 (E1)
B - BR
CAN communication line
Power switch on (IG)
Pulse generation
(see waveform 1)


    A086154E17
  1. WAVEFORM 1

    1. CAN communication signal
      Power management control ECU Terminal Name
      Between CA1H - E1 or CA2H - E1
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)

      HINT:
      The waveform varies depending on the CAN communication signal.



  2. A086155E19
  3. WAVEFORM 2

    1. CAN communication signal
      Power management control ECU Terminal Name
      Between CA1L - E1 or CA2L - E1
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)

      HINT:
      The waveform varies depending on the CAN communication signal.