Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM

PRE-CRASH SAFETY SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK SEAT BELT CONTROL ECU

E140518E21

  1. Disconnect the seat belt control ECU connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L2-7 (+B) - Body ground
    B - Body ground
    Battery voltage
    Always
    11 to 14 V
    L2-8 (PGND) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    L3-8 (IG1) - Body ground
    R - Body ground
    Seat belt control ECU power supply
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L2-2 (MOR+) - L2-1 (MOR-)
    B - W
    Seat belt motor RH power supply
    Power switch on (IG)
    4.0 to 8.5 V
    Power switch off
    Below 1 V
    L2-3 (MOL+) - L2-4 (MOL-)
    B - W
    Seat belt motor LH power supply
    Power switch on (IG)
    4.0 to 8.5 V
    Power switch off
    Below 1 V
    L3-5 (LBL+) - Body ground
    V - Body ground
    Front seat inner belt assembly line
    1. Power switch on (IG)
    2. Fasten passenger side seat belt
    Pulse generation
    (see waveform 1)
    L3-6 (LBL-) - Body ground
    R - Body ground
    Front seat inner belt assembly line
    Always
    Below 1 Ω
    If the result is not as specified, the ECU may be malfunctioning.



  5. Inspect using an oscilloscope.



    1. Waveform 1 (Reference)


      E192405E01

      Terminal
      L3-5 (LBL+) - Body ground
      Tool Setting
      2V/DIV., 20 ms./DIV.
      Condition
      Power switch on (IG), buckle switches are not installed
      Power switch on (IG), buckle switches are installed


CHECK DRIVING SUPPORT ECU

E184662E09

  1. Measure the voltage and/or resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L60-5 (PBSW) - Body ground
    L - Body ground
    Pre crash brake cancel switch
    Pre crash brake cancel switch ON
    Below 1 Ω
    Pre crash brake cancel switch off
    10 kΩ or higher
    L60-17 (CA2L) - L60-25 (GND)
    W - W-B
    CAN communication signal
    Power switch on (IG)
    Pulse generation
    (See waveform 1)
    L60-18 (CA1N) - L60-25 (GND)
    L - W-B
    CAN communication signal
    Power switch on (IG)
    Pulse generation
    (See waveform 2)
    L60-23 (CCS) - L60-25 (GND)
    V - W-B
    Cruise control main switch signal
    Power switch on (IG)
    10 to 14 V
    L60-23 (CCS) - L60-25 (GND)
    V - W-B
    Cruise control main switch signal
    Power switch on (IG),
    CANCEL switch on
    6.6 to 10.1 V
    L60-23 (CCS) - L60-25 (GND)
    V - W-B
    Cruise control main switch signal
    Power switch on (IG),
    Main switch on
    Below 1 V
    L60-25 (GND) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    L60-27 (STP-) - Body ground
    Y - Body ground
    Stop light switch signal input
    Brake pedal depressed
    7.5 to 14 V
    L60-27 (STP-) - Body ground
    Y - Body ground
    Stop light switch signal input
    Brake pedal released
    Below 1 V
    L60-28 (ST1-) - Body ground
    R - Body ground
    Stop light switch signal input
    Power switch on (IG),
    Brake pedal released
    7.5 to 14 V
    L60-28 (ST1-) - Body ground
    R - Body ground
    Stop light switch signal input
    Power switch on (IG),
    Brake pedal depressed
    Below 1 V
    L60-30 (B) - Body ground
    B - Body ground
    Power supply
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    L60-39 (CA2H) - L60-25 (GND)
    B - W-B
    CAN communication signal
    Power switch on (IG)
    Pulse generation
    (See waveform 3)
    L60-40 (CA1P) - L60-25 (GND)
    Y - W-B
    CAN communication signal
    Power switch on (IG)
    Pulse generation
    (See waveform 4)



  2. A086155E19
  3. WAVEFORM 1

    1. CAN communication signal
      Driving support ECU Terminal Name
      Between CA2L and GND
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)

      HINT:
      The waveform varies depending on the CAN communication signal.



  4. A086154E17
  5. WAVEFORM 2

    1. CAN communication signal
      Driving support ECU Terminal Name
      Between CA1N and GND
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)



  6. A086154E17
  7. WAVEFORM 3

    1. CAN communication signal
      Driving support ECU Terminal Name
      Between CA2H and GND
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)

      HINT:
      The waveform varies depending on the CAN communication signal.



  8. A086155E19
  9. WAVEFORM 4

    1. CAN communication signal
      Driving support ECU Terminal Name
      Between CA1P and GND
      Tester Range
      1 V/DIV., 10 μsec./DIV.
      Condition
      Power switch on (IG)