PRE-CRASH SAFETY SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Pre-Crash / Data List.
Enter the following menus: Body / Pre-Crash 2 / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Driver Buckle SW | Buckle switch status of driver side seat/ UNSET / SET / NG | UNSET: Driver side seat belt unfastened SET: Driver side seat belt fastened NG: Indeterminate data | - |
| Passenger Buckle SW | Buckle switch status of passenger side seat/ UNSET / SET / NG | UNSET: Passenger side seat belt unfastened SET: Passenger side seat belt fastened NG: Indeterminate data | - |
| Drive Belt Control | Seat belt control status of driver side seat/ STOP / ON / ERROR | STOP: Control stopped ON: Controlled ERROR: Indeterminate data | Seat belt (driver side) is fastened |
| Passenger Belt Control | Seat belt control status of passenger side seat/ STOP / ON / ERROR | STOP: Control stopped ON: Controlled ERROR: Indeterminate data | Seat belt (passenger side) is fastened |
| Number of Trouble Code | Number of past trouble codes/min: 0, max: 255 | Number of DTCs will be displayed | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Wiper Information | Wiper operational status/ Unoperat, Oil off, Mist, Washer, Unknown, Intermittent, Lo, Hi | The respective operational status displayed | - |
| Head Light information | Headlight operational status/ Unknown, Fail, Prohibited, Direct, Hi, Passing, Fail | - | - |
| Head Light | Headlight switch position signal/ ON or OFF | ON: Headlight switch on OFF: Headlight switch off | - |
| Head Light (High Beam) | High beam headlight switch position signal/ ON or OFF | ON: High beam headlight switch on OFF: High beam headlight switch off | - |
| Pre-Crash Brake OFF Switch | Pre-crash brake cancel switch status/ ON or OFF | ON: Pre-crash cancel switch on OFF: Pre-crash cancel switch off | - |
| Pre-Crash System | Pre-crash system control/ Valid or Inval | Valid: Pre-crash system control possible Inval: Pre-crash system control not possible | - |
| DCam Indicator | Driver camera indicator display request signal/ ON or OFF | ON: Driver camera indicator display requested OFF: Driver camera indicator display not requested | Not Supported |
| PCS Indicator | "CHECK PCS SYSTEM" display request signal/ ON or OFF | ON: "CHECK PCS SYSTEM" display requested OFF: "CHECK PCS SYSTEM" display not requested | - |
| PCS Disabled Indicator | "PCS TEMPORARILY NOT AVAILABLE" display request signal/ ON or OFF | ON: "PCS TEMPORARILY NOT AVAILABLE" display requested OFF: "PCS TEMPORARILY NOT AVAILABLE" display not requested | - |
| Pre-Crash Safety Warning Ind | PCS system warning status/ ON or OFF | ON: Pre-crash safety warning indicator on OFF: Pre-crash safety warning indicator off | - |
| Pre-Crash Safety Brake Ind | PCS system "BRAKE!" alert status/ ON or OFF | ON: PCS system "BRAKE!" alert on OFF: PCS system "BRAKE!" alert off | - |
| Pre-Crash Safety Warning Buz | PCS system warning buzzer/ Valid or Inval | Valid: PCS system warning buzzer operation possible Inval: PCS system warning buzzer operation not possible | - |
| Pre-Crash Brake | Pre-crash brake function/ Valid or Inval | Valid: Pre-crash brake operation possible Inval: Pre-crash brake operation not possible | - |
| Front Radar PSB | Front radar-linked pre-crash seat belt activation signal/ ON or OFF | ON: Front radar-linked pre-crash seat belt activated OFF: Front radar-linked pre-crash seat belt not activated | Status changes when the pre-crash seat belt is activated before a collision |
| PBA Start | Pre-crash brake assist activation signal/ ON or OFF | ON: Pre-crash brake assist activated OFF: Pre-crash brake assist not activated | Signal status changes when the pre-crash brake assist is activated before a collision (Pre-crash brake will activate only in situations where the driver depresses the brake pedal) |
| Warning Brake | Warning brake activation/ ON or OFF | ON: Warning brake operation activated OFF: Warning brake operation not activated | Signal status changes when the warning brake function lightly applies the brakes to warn the driver when signals from the driver monitor determine that the driver is not facing the camera |
| Brake Assist Standby | Supplemental brake pressure signal/ ON or OFF | ON: Supplemental brake pressure being provided OFF: Supplemental brake pressure not being provided | Signal status changes when supplemental brake pressure is being provided after a collision is judged as unavoidable and before the brake pedal is depressed |
| Pre-Crash Brake Control | Pre-crash brake operational status/ ON or OFF | ON: Pre-crash brake operating OFF: Pre-crash brake function not operating | Status changes when pre-crash brake operates before a collision |
| AVS Start | AVS control activation status/ ON or OFF | ON: AVS control activated OFF: AVS control not activated | Status changes when the suspension is controlled (stiffened) prior to a collision |
| CCS Cancel | Automatic cancellation of cruise control during pre-crash brake activation/ ON or OFF | ON: Cruise control automatically canceled OFF: Cruise control not automatically canceled | - |
| Front Radar-Dirt History | Millimeter wave radar sensor assembly dirt history/ ON or OFF | ON: History of excessive dirt OFF: No history of excessive dirt | - |
| Front Radar-Environment Hist | Millimeter wave radar sensor temperature condition history/ Good or Bad | Good: No history of excessive temperature Bad: History of excessive temperature | - |
| Camera Height | Memorized camera height/ Display range: Memorized camera height | Memorized camera height displayed | - |
| Camera Horizontal | Memorized camera horizontal position/ Display range: Memorized camera horizontal position | Memorized camera horizontal position displayed | - |
| Target Height | Memorized target height | Memorized target height displayed | - |
| Target Distance | Memorized target distance | Memorized distance from the camera to the target displayed | - |
| Curr Com PCS-WIL-R | Driver seat active headrest ECU connection status/ without or with | with: Driver seat active headrest ECU connected without: Driver seat active headrest ECU not connected | Not Supported |
| Curr Com PCS-WIL-L | Front passenger seat active headrest ECU connection status/ without or with | with: Front passenger seat active headrest ECU connected without: Front passenger seat active headrest ECU not connected | Not Supported |
| Curr Com Night View ECU | Night view ECU connection status/ without or with | with: Night view ECU connected without: Night view ECU not connected | Not Supported |
| Country# (DSS) | Destination country for driving support computer/ JPN, NA, EURO, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC, NOFIX | Actual country code | - |
| The Number of DTCs | Number of DTCs/ 0 to 255 | When system is normal: 0 When a malfunction is detected: More than 0 | - |
| ACTIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Pre-Crash / Active Test.
Perform Active Test according to the display on the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Driver Seat Belt Motor | Driver seat belt motor | ON: Seat belt motor operates OFF: Seat belt motor does not operate | Seat belt (driver side) is fastened |
| Passenger Seat Belt Motor | Passenger seat belt motor | ON: Seat belt motor operates OFF: Seat belt motor does not operate | Seat belt (passenger side) is fastened |
| Driver and Passenger Seat Belt Motor | Driver and passenger seat belt motors | ON: Seat belt motors operate OFF: Seat belt motors do not operate | Seat belts (driver and passenger sides) are fastened |