PRE-CRASH SAFETY SYSTEM > Power Source Circuit |

| 1.CHECK HARNESS AND CONNECTOR (PGND CIRCUIT) |
![]() |
Disconnect the seat belt control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L2-8 (PGND) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Seat Belt Control ECU) |
Reconnect the seat belt control ECU connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (IG1 CIRCUIT) |
![]() |
Disconnect the seat belt control ECU connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L3-8 (IG1) - L2-8 (PGND) | Power switch on (IG) | 11 to 14 V |
| *1 | Front view of wire harness connector (to Seat Belt Control ECU) |
Reconnect the seat belt control ECU connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (+B CIRCUIT) |
![]() |
Disconnect the seat belt control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L2-7 (+B) - Body ground | Always | 11 to 14 V |
| *1 | Front view of wire harness connector (to Seat Belt Control ECU) |
Reconnect the seat belt control ECU connector.
|
| ||||
| OK | ||
| ||
| 4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
Remove the instrument panel junction block assembly.

| *1 | Instrument Panel Junction Block Assembly | *2 | LHD |
| *3 | RHD | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2E-1 - 2B-16 | Always | 10 kΩ or higher |
| 2E-1 - 2B-16 | When battery voltage applied to terminals 2B-25 and 2B-6 | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| 2F-1 - 2B-16 | Always | 10 kΩ or higher |
| 2F-1 - 2B-16 | When battery voltage applied to terminals 2B-25 and 2B-6 | Below 1 Ω |
Reinstall the instrument panel junction block assembly.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - SEAT BELT CONTROL ECU) |
![]() |
Disconnect the instrument panel junction block assembly connector.
Disconnect the seat belt control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2B-16 - L3-8 (IG1) | Always | Below 1 Ω |
| 2B-16 - Body ground | Always | 10 kΩ or higher |
| L3-8 (IG1) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Seat Belt Control ECU) |
| *2 | Front view of wire harness connector (to Instrument Panel Junction Block Assembly) |
Reconnect the seat belt control ECU connector.
Reconnect the instrument panel junction block assembly connector.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BODY GROUND) |
![]() |
Disconnect the instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2B-6 - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Instrument Panel Junction Block Assembly) |
Reconnect the instrument panel junction block assembly connector.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL J/B - POWER MANAGEMENT CONTROL ECU) |
![]() |
Disconnect the instrument panel junction block assembly connector.
Disconnect the power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2B-25 - L6-2 (IG1D) | Always | Below 1 Ω |
| 2B-25 - Body ground | Always | 10 kΩ or higher |
| L6-2 (IG1D) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Power Management control ECU) |
| *2 | Front view of wire harness connector (to Instrument Panel Junction Block Assembly) |
Reconnect the power management control ECU connector.
Reconnect the instrument panel junction block assembly connector.
|
| ||||
| OK | ||
| ||