STEERING COLUMN ASSEMBLY > INSTALLATION |
| 1. INSPECT STEERING COLUMN ASSEMBLY |
Inspect the bushings.
![]() |
Check that the 2 bushings are securely installed to the steering column assembly.
| *1 | Bushing |
Check the 2 bushings for deformation and damage.
If the bushings are deformed or damaged, replace the steering column assembly with a new one.
Inspect the capsules.
![]() |
Check that the 2 capsules are securely installed to the steering column assembly as shown in the illustration.
| A | B |
| 2 mm (0.0787 in.) | 17 mm (0.669 in.) |
| *1 | Capsule |
Check the 2 capsules for deformation and damage.
If either of the capsules is deformed, loose, missing or damaged, replace the steering column assembly with a new one.
| 2. INSTALL NO. 1 STEERING COLUMN PROTECTOR (for RHD) |
![]() |
Install the No. 1 steering column protector to the steering column assembly with the bolt.
| 3. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly to install the No. 2 steering intermediate shaft assembly.
| *1 | Matchmark |
Install the bolt.
| 4. INSTALL STEERING POST ASSEMBLY |
![]() |
Install the steering post assembly with the bolt and 2 nuts.
Connect the connectors and engage the wire harness clamps to the steering post assembly.
![]() |
Connect the connector to the power steering ECU assembly.
![]() |
Connect the connector to the power steering ECU assembly.
Engage the 2 wire harness clamps.
| 5. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft to connect the No. 2 steering intermediate shaft assembly to the steering intermediate shaft.
| *1 | Matchmark |
Install the bolt.
| 6. INSTALL COLUMN HOLE COVER SILENCER SHEET |
![]() |
Install the column hole cover silencer sheet with the 2 clips.
Install the floor carpet.
| 7. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY |
![]() |
Engage the 2 claws to install the No. 2 air duct sub-assembly.
| 8. INSTALL NO. 1 HEATER TO REGISTER DUCT |
![]() |
Install the No. 1 heater to register duct with the 3 clips.
| 9. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY (for LHD) |
| 10. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY (for RHD) |
| 11. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY |
| 12. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY |
| 13. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD |
| 14. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Using pliers, expand the clamp.
| *1 | Clamp |
| *2 | Claw |
While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.
Return the clamp to its original position.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
| 15. INSTALL UPPER STEERING COLUMN COVER |
![]() |
Engage the 2 claws and 2 pins to install the upper steering column cover.
| 16. INSTALL LOWER STEERING COLUMN COVER |
![]() |
Engage the 2 claws to install the lower steering column cover.
![]() |
Engage the 4 claws.
![]() |
Engage the 2 claws.
| 17. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD |
| 18. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Rotate the spiral cable counterclockwise slowly by hand until it stops.
![]() |
Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
| *1 | Alignment Mark |
| 19. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel assembly and steering main shaft.
| *1 | Matchmark |
Install the steering wheel assembly set nut.
Connect the connectors to the spiral cable sub-assembly.
| 20. INSTALL STEERING PAD |
| 21. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD |
| 22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 23. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 24. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 25. INSTALL REAR NO. 2 FLOOR BOARD |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 26. INSPECT STEERING PAD |
![]() |
Visually check for defects with the steering pad installed on the vehicle.
The defects are as follows:
Make sure that the horn sounds.
| 27. INITIALIZE ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT |
| 28. INSPECT SRS WARNING LIGHT |
Inspect the SRS warning light (Click here).