DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0420 | Oxygen storage capacity value smaller than standard value under active air fuel ratio control (2 trip detection logic) |
|

| *1 | Air Fuel Ratio Sensor (Sensor 1) | *2 | Heated Oxygen Sensor (Sensor 2) |
| *3 | Exhaust Manifold Sub-assembly | *4 | Front Exhaust Pipe Assembly |
| *5 | Tail Exhaust Pipe Assembly | *6 | TWC: Front Catalyst |
| *7 | TWC: Rear Catalyst | - | - |



| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0420 is output | A |
| DTC P0420 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine warm it up.
Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.
Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the output voltages of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio) | 12.5% | Rich | Less than 3.1 V |
| AFS Voltage B1S1 (Air fuel ratio) | -12.5% | Lean | Higher than 3.4 V |
| O2S B1S2 (Heated oxygen) | 12.5% | Rich | Higher than 0.55 V |
| O2S B1S2 (Heated oxygen) | -12.5% | Lean | Less than 0.4 V |
| Status of AFS Voltage B1S1 | Status of O2S B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensor Condition | Misfire | Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | - | Air fuel ratio sensor | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | - | Air fuel ratio sensor | B |
| Lean/Rich | Lean | Heated oxygen sensor malfunction | - |
| C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction | - |
| C |
| Lean | Lean | Actual air fuel ratio lean | May occur |
| D |
| Rich | Rich | Actual air fuel ratio rich | - |
| D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.INSPECT FOR EXHAUST GAS LEAK |
Inspect for exhaust gas leaks.
|
| ||||
| OK | |
| 4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST) |
Replace the front exhaust pipe assembly (TWC: Front and rear catalyst) (Click here).
| NEXT | ||
| ||
| 5.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1) |
Replace the air fuel ratio sensor (sensor 1) (Click here).
|
| ||||
| 6.INSPECT FOR EXHAUST GAS LEAK |
Inspect for exhaust gas leaks.
|
| ||||
| OK | |
| 7.REPLACE HEATED OXYGEN SENSOR (SENSOR 2) |
Replace the heater oxygen sensor (sensor 2) (Click here).
|
| ||||
| 8.INSPECT FOR EXHAUST GAS LEAK |
Inspect for exhaust gas leaks.
|
| ||||
| OK | |
| 9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO |
Check the case of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure .
|
| ||||
| 10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT |
Repair or replace exhaust gas leak point.
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0420 is output | A |
| DTC is not output (No pending DTCs output) | B |
|
| ||||
| A | |
| 12.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST) |
Replace the front exhaust pipe assembly (TWC: Front and rear catalyst) (Click here).
| NEXT | ||
| ||