Home › Suspension › REAR SUSPENSION › REAR AXLE BEAM

REAR AXLE BEAM > REMOVAL

for Preparation Click here



1. PRECAUTION (w/ Navigation System for HDD)

NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and setting. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



3. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



4. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



5. DISABLE BRAKE CONTROL
  1. Wait at least 2 minutes after the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C205666
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



6. REMOVE REAR WHEELS


7. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)


    B227761
  1. Disengage the 10 claws and remove the front door scuff plate LH.



8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD)


    B227764
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.



9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)


    B223460
  1. Remove the screw <C>.



    B223461
  1. Disengage the 6 claws and clip as shown in the illustration.



    B223463
  1. Disengage the claw and 2 guides and disconnect the hood lock control cable.

  1. Disconnect each connector and clamp, and remove the lower instrument panel finish panel assembly.



10. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    B223634
  1. Remove the screw <D>.

  1. Disengage the 2 claws and guide.

  1. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.



11. LOOSEN PARKING BRAKE CABLE
  1. Completely release the parking brake pedal.



    C206641E01
  1. Loosen the lock nut and adjusting nut to completely release the parking brake cable.
    Text in Illustration 
    *1
    Lock Nut
    *2
    Adjusting Nut



12. DRAIN BRAKE FLUID

NOTICE:
If brake fluid leaks onto any painted surface, immediately wash it off.



13. REMOVE REAR FLOOR SIDE MEMBER COVER LH


    C207250
  1. Remove the nut, 2 bolts and rear floor side member cover LH.



14. REMOVE REAR FLOOR SIDE MEMBER COVER RH


    C207251
  1. Remove the 3 bolts.

  1. Disengage the clip and remove the rear floor side member cover RH.



15. REMOVE REAR SUSPENSION BRACE SUB-ASSEMBLY


  1. Remove the 4 bolts.


    C207257

  1. Disengage the clip and remove the rear suspension brace sub-assembly.



16. DISCONNECT REAR SPEED SENSOR WIRE (for LH Side)


    C208053
  1. Using a screwdriver, disconnect the connector from the rear speed sensor.

    NOTICE:
    Be careful not to damage the rear speed sensor.



17. DISCONNECT REAR SPEED SENSOR WIRE (for RH Side)

HINT:
Perform the same procedure as for the LH side.



18. SEPARATE REAR SPEED SENSOR WIRE (for LH Side)


    C207255
  1. Remove the nut and separate the 2 clamps and rear speed sensor wire.



19. SEPARATE REAR SPEED SENSOR WIRE (for RH Side)

HINT:
Perform the same procedure as for the LH side.



20. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C155545E01
  1. Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.



    C155546E03
  1. Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.
    Text in Illustration 
    *1
    No. 3 Parking Brake Cable Assembly
    *2
    Clip
    *3
    Offset Wrench (14 mm)

    HINT:
    Insert an offset wrench (14 mm) at the base of the No. 3 parking brake cable assembly as shown in the illustration to disengage the clip. Pull out the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.



21. DISCONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:
Perform the same procedure as for the No. 3 parking brake cable assembly.



22. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C156828
  1. Remove the bolt and separate the No. 3 parking brake cable assembly.



23. SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:
Perform the same procedure as for the No. 3 parking brake cable assembly.



24. SEPARATE REAR BRAKE TUBE FLEXIBLE HOSE


  1. Using a union nut wrench, disconnect the 2 brake lines while holding the rear brake tube flexible hose with a wrench.


    C207258E01


    Text in Illustration 
    *1
    LH Side
    *2
    RH Side

    NOTICE:
    1. Do not bend or damage the brake line.
    2. Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting points.

  1. for LH Side

    1. Remove the bolt and separate the rear brake tube flexible hose from the rear axle beam assembly.

  1. for RH Side

    1. Remove the clip and separate the rear brake tube flexible hose from the rear axle beam assembly.



25. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY LH


    C205529
  1. Using a union nut wrench, disconnect the brake line while holding the rear flexible hose LH with a wrench.

    NOTICE:
    1. Do not bend or damage the brake line.
    2. Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting points.



    C158399
  1. Remove the clip and separate the rear flexible hose LH.



    C207078
  1. Remove the 2 bolts and rear disc brake caliper assembly LH with rear flexible hose LH.



26. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



27. REMOVE REAR DISC (for LH Side)


    C151123E03
  1. Remove the rear disc.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Place matchmarks on the disc and axle hub.



28. REMOVE REAR DISC (for RH Side)

HINT:
Perform the same procedure as for the LH side.



29. REMOVE REAR NO. 4 BRAKE TUBE


    C155135
  1. Remove the nut and rear No. 4 brake tube from the rear axle beam assembly.



30. REMOVE REAR NO. 3 BRAKE TUBE

HINT:
Perform the same procedure as for the rear No. 4 brake tube.



31. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH


    C207079
  1. Remove the 4 bolts, rear axle hub and bearing assembly and rear disc brake dust cover from the rear axle beam assembly.



32. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



33. SEPARATE REAR WHEEL HOUSE LINER LH


    C207233
  1. Remove the clip and turn back the rear wheel house liner LH to separate the rear wheel house liner LH.



34. SEPARATE REAR WHEEL HOUSE LINER RH

HINT:
Perform the same procedure as for the LH side.



35. SEPARATE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH (w/ Height Control Sensor)


    C207241
  1. Remove the bolt and separate the rear height control sensor sub-assembly RH from the rear axle beam assembly.



    C207242E01
  1. Using a vinyl tape, secure the rear height control sensor sub-assembly RH as shown in the illustration.
    Text in Illustration 
    *1
    Vinyl Tape



36. REMOVE REAR COIL SPRING LH


    C207243E01
  1. Loosen the 2 bolts.
    Text in Illustration 
    *1
    LH Side
    *2
    RH Side

    NOTICE:
    Do not remove the bolts.



  1. Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.


    C207239E01


    Text in Illustration 
    *1
    Jack
    *2
    Wooden Block

    CAUTION:
    Do not jack up the rear axle beam assembly too high as the vehicle may fall.

    HINT:
    Support the rear shock absorber at a position where it compresses by approximately 20 to 30 mm (0.787 to 1.18 in.).

  1. Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

    NOTICE:
    Since the stopper nuts are used, turn the bolts.



    C207244
  1. Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks, and remove the rear coil spring LH.

    NOTICE:
    When moving the rear axle beam assembly beyond full rebound, make sure that the rear axle beam assembly is not out of position for more than 10 minutes.



  1. Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks, and temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts and 2 nuts.


    C207240E01


    Text in Illustration 
    *1
    Jack
    *2
    Wooden Block

    NOTICE:
    Since the stopper nuts are used, turn the bolts.



37. REMOVE REAR COIL SPRING RH

HINT:
Perform the same procedure as for the LH side.



38. REMOVE REAR UPPER COIL SPRING INSULATOR LH


39. REMOVE REAR UPPER COIL SPRING INSULATOR RH


40. REMOVE REAR LOWER COIL SPRING INSULATOR LH


41. REMOVE REAR LOWER COIL SPRING INSULATOR RH


42. REMOVE REAR AXLE BEAM ASSEMBLY


  1. Support the rear axle beam assembly with a jack using 2 wooden blocks and 2 attachments or equivalent tools to replicate standard vehicle height conditions as shown in the illustration.


    C207252E01


    Text in Illustration 
    *1
    Jack
    *2
    Wooden Block
    *3
    Attachment
    -
    -

    NOTICE:
    Make sure to secure the rear axle beam assembly to prevent it from dropping.

  1. Remove the 2 bolts (A) and 2 nuts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

    NOTICE:
    Since the stopper nuts are used, turn the bolts.

  1. Remove the 2 bolts (B) and rear axle beam assembly.



43. REMOVE REAR AXLE CARRIER BUSHING LH


    C159021E04
  1. Put a matchmark on the rear axle beam assembly so that the mark aligns with the arrow mark on the rear axle carrier bushing LH. (If the rear axle beam assembly is reused.)
    Text in Illustration 
    *1
    Matchmark



    C190682E05
  1. Using a chisel and hammer, bend the 2 ribs on the rear axle carrier bushing LH.
    Text in Illustration 
    *1
    Bend Portion
    *2
    Turn
    *3
    Hold

    NOTICE:
    When removing the rear axle carrier bushing, do not erase the matchmark on the rear axle beam assembly.

  1. Using SST, remove the rear axle carrier bushing LH from the rear axle beam assembly.

    SST
    09710-26011   (09710-05061)
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011)
    09950-60010   (09951-00530)

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt before use.



44. REMOVE REAR AXLE CARRIER BUSHING RH

HINT:
Perform the same procedure as for the LH side.