Home › Suspension › REAR SUSPENSION › REAR COIL SPRING

REAR COIL SPRING > INSTALLATION

for Preparation Click here



1. INSTALL REAR UPPER COIL SPRING INSULATOR LH


    C207238E01
  1. Install the rear upper coil spring insulator LH to the rear coil spring LH.
    Text in Illustration 
    *1
    10 mm or less

    NOTICE:
    Install the rear upper coil spring insulator so that the dimension between the stopper and the upper end of the rear coil spring is 10 mm (0.394 in.) or less.



2. INSTALL REAR UPPER COIL SPRING INSULATOR RH

HINT:
Perform the same procedure as the LH side.



3. INSTALL REAR LOWER COIL SPRING INSULATOR LH


4. INSTALL REAR LOWER COIL SPRING INSULATOR RH


5. INSTALL REAR COIL SPRING LH


  1. Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.


    C207240E01


    Text in Illustration 
    *1
    Jack
    *2
    Wooden Block

  1. Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

    NOTICE:
    Since the stopper nuts are used, turn the bolts.

  1. Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks.



    C207237E01
  1. Set the rear coil spring LH to the rear axle beam assembly.
    Text in Illustration 
    *1
    Identification Mark
    *2
    30° or less

    NOTICE:
    Set the rear coil spring so that the identification marks are positioned as shown in the illustration.



  1. Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks and temporarily install the rear axle beam assembly and rear coil spring LH with the 2 bolts and 2 nuts.


    C207239E01


    Text in Illustration 
    *1
    Jack
    *2
    Wooden Block

    NOTICE:
    Since the stopper nuts are used, turn the bolts.

    HINT:
    Insert the bolt with the threaded end facing the outside of the vehicle.



6. INSTALL REAR COIL SPRING RH

HINT:
Perform the same procedure as the LH side.



7. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH (w/ Height Control Sensor)


    C207241
  1. Install the rear height control sensor sub-assembly RH to the rear axle beam assembly with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



8. INSTALL REAR SPEED SENSOR WIRE (for LH Side)


    C207255
  1. Install the rear speed sensor wire to the rear axle beam assembly with the nut and 2 clamps.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not twist the rear speed sensor wire when installing it.



9. INSTALL REAR SPEED SENSOR WIRE (for RH Side)

HINT:
Perform the same procedure as the LH side.



10. CONNECT REAR SPEED SENSOR WIRE (for LH Side)


    C208054
  1. Connect the rear speed sensor wire connector to the rear speed sensor.



11. CONNECT REAR SPEED SENSOR WIRE (for RH Side)

HINT:
Perform the same procedure as the LH side.



12. INSTALL REAR WHEELS

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



13. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Bounce the vehicle up and down several times to stabilize the suspension.



14. FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY


    C207247E01
  1. Fully tighten the 2 bolts.
    Text in Illustration 
    *1
    LH Side
    *2
    RH Side

    Torque:
    135 N*m{ 1377 kgf*cm , 100 ft.*lbf }

    NOTICE:
    The final torque must be applied under the standard vehicle height conditions.



    C207245E01
  1. Fully tighten the 2 bolts.
    Text in Illustration 
    *1
    LH Side
    *2
    RH Side

    Torque:
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }

    NOTICE:
    1. Since the stopper nut are used, turn the bolts.
    2. The final torque must be applied under the standard vehicle height conditions.



15. INSTALL REAR WHEEL HOUSE LINER LH


    C207233
  1. Install the rear wheel house liner LH with the clip.



16. INSTALL REAR WHEEL HOUSE LINER RH

HINT:
Perform the same procedure as the LH side.



17. INSPECT REAR WHEEL ALIGNMENT
Click here.


18. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


19. PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION
Click here.


20. CHECK FOR SPEED SENSOR SIGNAL
Click here.


21. PERFORM INITIALIZATION (w/ Height Control Sensor)

NOTICE:
Some systems need to be initialized after the rear height control sensor sub-assembly RH is replaced (Click here).