DTC B27A2 Open in Front Passenger Side Electrical Antenna Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B27A2 | Open circuit detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger side) terminals (between CLG2 and ANT1, or CG2B and ANT2). |
|

| 1.CHECK CONNECTOR CONNECTION CONDITION |
Turn the power switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the front door outside handle assembly (for front passenger side).
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE) |
Disconnect the certification ECU (smart key ECU assembly) connector.
![]() |
Disconnect the front door outside handle assembly (for front passenger side) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L62-5 (CLG2) - z4-6 (ANT1) | Always | Below 1 Ω |
| L62-6 (CG2B) - z4-3 (ANT2) | Always | Below 1 Ω |
| L62-5 (CLG2) - Body ground | Always | 10 kΩ or higher |
| L62-6 (CG2B) - Body ground | Always | 10 kΩ or higher |
| z4-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| z4-3 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| L62-5 (CLG2) - z3-6 (ANT1) | Always | Below 1 Ω |
| L62-6 (CG2B) - z3-3 (ANT2) | Always | Below 1 Ω |
| L62-5 (CLG2) - Body ground | Always | 10 kΩ or higher |
| L62-6 (CG2B) - Body ground | Always | 10 kΩ or higher |
| z3-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| z3-3 (ANT2) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Certification ECU (Smart Key ECU Assembly)) |
| *2 | Front view of wire harness connector (to Front Door Outside Handle Assembly (for Front Passenger Side)) |
| *3 | for LHD |
| *4 | for RHD |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - BODY GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z4-2 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| z3-2 (GND) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Front Door Outside Handle Assembly (for Front Passenger Side)) |
| *2 | for LHD |
| *3 | for RHD |
|
| ||||
| OK | |
| 4.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (DOOR ELECTRICAL KEY OSCILLATOR SIGNAL OUTPUT) |
![]() |
Reconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance and check for pulses according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L62-15 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| L62-5 (CLG2) - L62-15 (E) |
| No pulse generation |
| L62-5 (CLG2) - L62-15 (E) |
| Pulse generation |
| L62-6 (CG2B) - L62-15 (E) |
| No pulse generation |
| L62-6 (CG2B) - L62-15 (E) |
| Pulse generation |
| *1 | Component with harness connected (Certification ECU (Smart Key ECU Assembly)) |
|
| ||||
| OK | |
| 5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Front Passenger Side) |
Replace the front door outside handle assembly (for front passenger side) (Click here).
| NEXT | |
| 6.CHECK DTC OUTPUT |
Clear the DTCs (Click here).
Recheck for DTCs.
|
| ||||
| OK | ||
| ||