Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)

DTC    B27A7    Open in Inside Luggage Compartment Electrical Key Oscillator Circuit

for Preparation Click here


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and sends it to the indoor electrical key oscillator (for rear floor). To detect the key inside the cabin, the indoor electrical key oscillator (for rear floor) creates a detection area in the cabin.
DTC B27A7 is detected by the certification ECU (smart key ECU assembly) when an open circuit occurs between the certification ECU (smart key ECU assembly) and indoor electrical key oscillator (for rear floor) terminals (between CLG7 and CLG6, or CG7B and CLGB).

DTC No.
DTC Detection Condition
Trouble Area
B27A7
Open circuit detected between the certification ECU (smart key ECU assembly) and indoor electrical key oscillator (for rear floor) terminals (between CLG7 and CLG6, or CG7B and CLGB).
  1. Indoor electrical key oscillator (for rear floor)
  2. Certification ECU (smart key ECU assembly)
  3. Wire harness or connector

WIRING DIAGRAM


B203534E09


INSPECTION PROCEDURE

NOTICE:
The entry and start system (for entry function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for entry function) after confirming that the communication system is functioning properly.

1.CHECK CONNECTOR CONNECTION CONDITION
  1. Turn the power switch off.

  1. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the indoor electrical key oscillator (for rear floor).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - INDOOR ELECTRICAL KEY OSCILLATOR)
  1. Disconnect the certification ECU (smart key ECU assembly) connector.



    B203519E13
  1. Disconnect the indoor electrical key oscillator (for rear floor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L62-26 (CLG7) - S15-1 (CLG6)
    Always
    Below 1 Ω
    L62-27 (CG7B) - S15-3 (CLGB)
    Always
    Below 1 Ω
    L62-26 (CLG7) - Body ground
    Always
    10 kΩ or higher
    L62-27 (CG7B) - Body ground
    Always
    10 kΩ or higher
    S15-1 (CLG6) - Body ground
    Always
    10 kΩ or higher
    S15-3 (CLGB) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    *2
    Front view of wire harness connector
    (to Indoor Electrical Key Oscillator (for Rear Floor))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (INDOOR ELECTRICAL KEY OSCILLATOR SIGNAL OUTPUT)


    B203530E20
  1. Reconnect the certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance and check for pulses according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L62-15 (E) - Body ground
    Always
    Below 1 Ω

    Standard:
    Tester Connection
    Condition
    Specified Condition
    L62-26 (CLG7) - L62-15 (E)
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) not touched
    No pulse generation
    L62-26 (CLG7) - L62-15 (E)
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) touched
    Pulse generation
    L62-27 (CG7B) - L62-15 (E)
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) not touched
    No pulse generation
    L62-27 (CG7B) - L62-15 (E)
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. Door outside handle assembly (lock sensor) touched
    Pulse generation

    Text in Illustration 
    *1
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


4.REPLACE INDOOR ELECTRICAL KEY OSCILLATOR (for Rear Floor)
  1. Replace the indoor electrical key oscillator (for rear floor) (Click here).


NEXT


5.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs.

    OK:
    DTC B27A7 is not output.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (INDOOR ELECTRICAL KEY OSCILLATOR WAS DEFECTIVE)