ELECTRONICALLY CONTROLLED BRAKE SYSTEM > INITIALIZATION |
| DESCRIPTION |
Perform initialization, calibration of the linear solenoid valve and emergency brake signal learning when the brake booster with master cylinder (skid control ECU, brake actuator or pressure sensor), brake pedal stroke sensor or brake pedal is replaced.
Follow the procedure to perform initialization.
| Part to be Replaced | Necessary Operation |
| Brake booster with master cylinder (Skid control ECU, brake actuator or pressure sensor) |
|
|
|
| PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE (When Using the Intelligent Tester) |
Clear the stored linear solenoid valve calibration data.
Turn the power switch off.
Check that the steering wheel is centered.
Check that park (P) is selected.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Select the skid control ECU to clear the linear solenoid valve calibration data using the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / Reset Memory.
Perform initialization and calibration of the linear solenoid valve.
Turn the power switch off.
Check that the steering wheel is centered.
Check that park (P) is selected.
Check that the parking brake is released.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG) with the brake pedal released.
Turn the intelligent tester on.
Switch the skid control ECU to the Test Mode using the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / ECB* Utility / Linear Valve Offset.
*: Electronically Controlled Brake System
Leave the vehicle stationary without depressing the brake pedal for 1 or 2 minutes.
![]() |
Check that the interval between blinks of the brake warning light / yellow (minor malfunction) changes from 1 second to 0.25 seconds.
Check that DTC C1345 (Linear Solenoid Valve Offset Learning Undone) which indicates trouble with stroke sensor zero point learning is not output when the brake warning light / yellow (minor malfunction) changes to the Test Mode display upon initialization and calibration of the linear solenoid valve completion.
Perform the zero point calibration of yaw rate and acceleration sensor (Click here).
Enter the normal mode from the Test Mode following the intelligent tester directions.
Turn the power switch off and disconnect the intelligent tester.
| PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE (When not Using the Intelligent Tester) |
Clear the stored linear solenoid valve calibration data.
Turn the power switch off.
Check that the steering wheel is centered.
Check that park (P) is selected.
Check that the parking brake is released.
Turn the power switch on (IG) with the brake pedal released.
![]() |
Using SST, connect and disconnect terminals TS and CG of the DLC3 4 times or more within 8 seconds.
| *1 | Front view of DLC3 |
Check that no codes other than ABS code 42, VSC code 45 and electronically controlled brake system code 48, 66, or 95 are stored in the diagnostic system.

Perform initialization and calibration of the linear solenoid valve.
Turn the power switch off.
Check that the steering wheel is centered.
Check that park (P) is selected.
![]() |
Using SST, connect terminals TS and CG of the DLC3.
| *1 | Front view of DLC3 |
Turn the power switch on (IG) with the brake pedal released.
Leave the vehicle stationary without depressing the brake pedal for 1 or 2 minutes.
![]() |
Check that the interval between blinks of the brake warning light / yellow (minor malfunction) changes from 1 second to 0.25 seconds.
Check that DTC 66 (Linear Solenoid Valve Offset Learning Undone) which indicates trouble with stroke sensor zero point learning is not output when the brake warning light / yellow (minor malfunction) changes to the Test Mode display upon initialization and calibration of the linear solenoid valve completion.
Perform the zero point calibration of yaw rate and acceleration sensor (Click here).
Turn the power switch off and disconnect SST from the DLC3.
| PERFORM EMERGENCY BRAKE SIGNAL LEARNING (w/ Emergency Brake Signal) |
Perform emergency brake signal Learning.
Turn the power switch off.
Check that the steering wheel is centered.
Check that park (P) is selected.
Check that the parking brake is applied.
Check that the hazard warning switch is off.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Switch the skid control ECU to the Test Mode using the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / Test Mode.
![]() |
Check that the brake warning light / yellow (minor malfunction) come on for several seconds and then blink in Test Mode.
Switch the skid control ECU to the Active Test using the intelligent tester. Enter the following menus: Chassis / ABS/VSC/ TRC / Active Test. (Check that the brake warning light / yellow (minor malfunction) blinks.)
Select the Active Test on the intelligent tester. Enter the following menus: Chassis / ABS/VSC/ TRC / Active Test / EBS Relay.
Select the Data List on the intelligent tester. Enter the following menus: Chassis / ABS/VSC/ TRC / Data List / EBS Relay.
Perform the Active Test.
After performing the Active Test, check that ON is shown in the Data List.
While the Active Test is performed (EBS Relay is ON displayed), depress the brake pedal to see if the stop lights flash for 1 second or more.
Enter the normal mode from the Test Mode following the intelligent tester directions.