Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM (w/ EGR System)

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is set, check the No. 1 ignition coil assembly circuit.
  3. If DTC P0352 is set, check the No. 2 ignition coil assembly circuit.
  4. If DTC P0353 is set, check the No. 3 ignition coil assembly circuit.
  5. If DTC P0354 is set, check the No. 4 ignition coil assembly circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is an ignition system in which each cylinder is ignited by it's own ignition coil assembly and spark plug. The secondary wiring of each ignition coil generates a powerful voltage which is applied directly to each spark plug. The spark passes from the center electrode of the spark plug to the ground electrode.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.

A217963E05


DTC No.
DTC Detection Conditions
Trouble Areas
P0351
P0352
P0353
P0354
No IGF signal to ECM while engine running
(1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 4) between ignition coil assembly and ECM
  3. No. 1 to No. 4 ignition coil assemblies
  4. ECM

  1. A205550E01
  2. Reference: Inspection using an oscilloscope.
  3. While cranking or idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
    ECM Terminal Name
    Between IGT (1 to 4) and E1
    Between IGF1 and E1
    Tester Range
    2 V/DIV., 20 ms./DIV.
    Condition
    Idling

WIRING DIAGRAM


A220106E03


A216529E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)


    A194110E19
  1. Disconnect the ignition coil assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D23-4 (GND) - Body ground
    Always
    Below 1 Ω
    D22-4 (GND) - Body ground
    Always
    Below 1 Ω
    D21-4 (GND) - Body ground
    Always
    Below 1 Ω
    D20-4 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Ignition Coil Assembly)

  1. Reconnect the ignition coil assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
OK


2.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)


    A194110E20
  1. Disconnect the ignition coil assembly connectors.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D23-1 (+B) - D23-4 (GND)
    Power switch on (IG)
    11 to 14 V
    D22-1 (+B) - D22-4 (GND)
    Power switch on (IG)
    11 to 14 V
    D21-1 (+B) - D21-4 (GND)
    Power switch on (IG)
    11 to 14 V
    D20-1 (+B) - D20-4 (GND)
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Ignition Coil Assembly)

  1. Reconnect the ignition coil assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - IG2 RELAY)
OK


3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)


  1. Disconnect the ignition coil assembly connectors.


    A194111E11

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D23-2 (IGF) - D28-23 (IGF1)
    Always
    Below 1 Ω
    D22-2 (IGF) - D28-23 (IGF1)
    Always
    Below 1 Ω
    D21-2 (IGF) - D28-23 (IGF1)
    Always
    Below 1 Ω
    D20-2 (IGF) - D28-23 (IGF1)
    Always
    Below 1 Ω


    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D23-3 (IGT1) - D28-108 (IGT1)
    Always
    Below 1 Ω
    D22-3 (IGT2) - D28-107 (IGT2)
    Always
    Below 1 Ω
    D21-3 (IGT3) - D28-106 (IGT3)
    Always
    Below 1 Ω
    D20-3 (IGT4) - D28-105 (IGT4)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D23-2 (IGF) or D28-23 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D22-2 (IGF) or D28-23 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D21-2 (IGF) or D28-23 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D20-2 (IGF) or D28-23 (IGF1) - Body ground
    Always
    10 kΩ or higher


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D23-3 (IGT1) or D28-108 (IGT1) - Body ground
    Always
    10 kΩ or higher
    D22-3 (IGT2) or D28-107 (IGT2) - Body ground
    Always
    10 kΩ or higher
    D21-3 (IGT3) or D28-106 (IGT3) - Body ground
    Always
    10 kΩ or higher
    D20-3 (IGT4) or D28-105 (IGT4) - Body ground
    Always
    10 kΩ or higher


    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Ignition Coil Assembly)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.

  1. Reconnect the ignition coil assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Shuffle arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine and wait for 10 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    Same DTC output
    A
    Different ignition coil DTC output
    B



B
REPLACE IGNITION COIL ASSEMBLY (Click here)
A

REPLACE ECM (Click here)