Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)

ENTRY AND START SYSTEM (for Start Function) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Power Source Control / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch1
    Stop light switch 1/ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Start Switch1
    Start switch 1/ON or OFF
    ON: Power switch pushed
    OFF: Power switch not pushed
    -
    Start Switch2
    Start switch 2/ON or OFF
    ON: Power switch pushed
    OFF: Power switch not pushed
    -
    Latch Circuit
    Latch circuit/ON or OFF
    ON: Power switch on (IG) or on (READY)
    OFF: Power switch off or on (ACC)
    -
    IG1 Relay Monitor (Outside)
    IG1 outer relay monitor/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    IG1 Relay Monitor (Inside)
    IG1 inner relay monitor/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    IG2 Relay Monitor (Outside)
    IG2 outer relay monitor/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    IG2 Relay Monitor (Inside)
    IG2 inner relay monitor/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    Starter Request Signal
    Starter request signal monitor/ON or OFF
    ON: ST relay on
    OFF: ST relay off
    -
    ACC Relay Monitor
    ACC relay monitor/ON or OFF
    ON: Power switch on (ACC)
    OFF: Power switch off
    -
    Ready Signal
    Status of the ready signal/ON or OFF
    ON: Hybrid control system on (on (READY))
    OFF: Hybrid control system off
    -
    Vehicle Speed Signal
    Vehicle speed signal/Stop or Run
    Stop: Vehicle stopped
    Run: Vehicle running
    -
    Shift P Signal Pulse
    Status of the shift P signal pulse/Unknown, Error2, Normal2, Error1, Normal3, Error3 or Normal1
    Unknown: Other
    Error2: Signal abnormal and park (P) selected
    Normal2: Signal normal and park (P) selected
    Error1: Signal abnormal and park (P) state cannot be determined
    Normal3: Signal normal and R, N, D or B selected
    Error3: Signal abnormal and R, N, D or B selected
    Normal1: Signal normal and park (P) state cannot be determined
    -
    Power Supply Condition
    Power supply condition/All OFF, ACC ON, IG1 ON, IG2 ON, ST ON
    All OFF: All relays off
    ACC ON: ACC relay on
    IG1 ON: IG1 relay on
    IG2 ON: IG2 relay on
    ST ON: ST request signal on
    -
    Powertrain Type
    Status of the powertrain type/HV-AT, Conventional-AT, Conventional-MT, Conventional-MMT
    HV-AT
    -
    IG1 Circuit
    Status of the IG1 relay activation circuit/OK or NG
    OK: IG1 relay activation circuit normal
    NG: IG1 relay activation circuit abnormal
    -
    IG2 Circuit
    Status of the IG2 relay activation circuit/OK or NG
    OK: IG2 relay activation circuit normal
    NG: IG2 relay activation circuit abnormal
    -
    Starter Switch Signal Mismatch
    Power switch error detection/No or Yes
    No: Power switch error not detected
    Yes: Power switch error detected
    -
    Park Signal Mismatch
    Status of the park signal mismatch/No or Yes
    No: Park signal mismatch no detected
    Yes: Park signal mismatch detected
    -
    Key Certification Waiting Timed Out
    Key certification error detection/No or Yes
    No: Key certification error not detected
    Yes: Key certification error detected
    -
    Number of Diagnosis Code
    Number of diagnosis code/Min.: 0, MAX.: 255
    Number of DTCs will be displayed
    -

  6. Enter the following menus: Body / Entry & Start / Data List.

  7. Read the Data List according to the display on the intelligent tester.

    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ignition Switch
    Power switch/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    Key Low Battery
    Low key battery/Yes or No
    Yes: Key battery voltage low
    No: Key battery voltage normal
    -
    # Code
    Number of DTC recorded/Min.: 0, Max.: 225
    Number of DTCs displayed
    -
    Steering Lock Sleep Cond
    Transmission control ECU sleep condition/Yes or No
    Yes: Transmission control ECU sleep mode can be entered
    No: Transmission control ECU sleep mode cannot be entered
    -
    Steering Lock Start Cond
    Transmission control ECU start signal/Yes or No
    Yes: Transmission control ECU sent a start signal
    No: Transmission control ECU did not send a start signal
    -
    Engine Start Condition
    Hybrid control system start condition/OK or NG
    OK: Hybrid control system allowed to start
    NG: Hybrid control system not allowed to start
    -
    Engine Start Request
    Start request condition signal/OK or NG
    OK: Start request condition signal received
    NG: Start request condition signal not received
    -
    3bit Code Request
    Status of the 3-bit code request/OK or NG
    OK: 3-bit code request signal received
    NG: 3-bit code request signal not received
    -
    S Code Check
    S code certification result/OK or NG
    OK: Certification confirmed
    NG: Certification not confirmed
    -
    L Code Check
    L code certification result/OK or NG
    OK: Certification confirmed
    NG: Certification not confirmed
    -
    Unlock Request Receive
    Status of the gearshift control unlock request receive/OK or NG
    OK: Gearshift control unlock request signal received
    NG: Gearshift control unlock request signal not received
    -
    Lock Request Receive
    Status of the gearshift control lock request receive/OK or NG
    OK: Gearshift control lock request signal received
    NG: Gearshift control lock request signal not received
    -
    S Code Check (Past)
    S code certification result (Past)/OK or NG
    OK: Certification confirmed (past)
    NG: Certification not confirmed (past)
    -
    L Code Check (Past)
    L code verification result (Past)/OK or NG
    OK: Certification confirmed (past)
    NG: Certification not confirmed (past)
    -
    EFI Code Receive
    SFI communication (when DTC stored)/OK or NG
    OK: SFI code received
    NG: SFI code not received
    -
    EFI Communication
    SFI communication /OK or NG
    OK: SFI communication normal
    NG: SFI communication abnormal
    -
    Ignition Available Area
    Ignition available area/Front or All
    Customization status displayed
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relay, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Power Source Control / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicator Condition
    Power switch indicator
    Green/Red/No Sig
    Power switch on (READY)

  6. Enter the following menus: Body / Entry & Start / Active Test.

  7. Perform the Active Test according to the display on the intelligent tester.

    Entry & Start 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power / Engine SW Light
    Power switch illumination
    ON/OFF
    -