Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)

ENTRY AND START SYSTEM (for Entry Function) > Driver Side Door Entry Lock and Unlock Functions do not Operate

for Preparation Click here


DESCRIPTION

When the entry lock and unlock functions do not operate only for the driver door, an error in output request codes from the driver door or malfunction in the front door outside handle assembly is suspected. If the entry functions for the other doors operate normally, then the communication circuit between the key and door control receiver assembly is functioning normally. In this case, radio wave interference or a malfunction in the request code sending circuit (from the certification ECU (smart key ECU assembly) to the front door outside handle assembly (for driver side)) is suspected.

WIRING DIAGRAM


B203516E10


INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for entry function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for entry function) after confirming that the communication system is functioning properly.
  2. Confirm that another key is not in the cabin.

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table) (Click here)
OK


2.CHECK WAVE ENVIRONMENT


    B229643E02
  1. Bring the key near the front door outside handle assembly (for driver side), and perform a driver door entry lock and unlock operation check.

    NOTICE:
    If the key is brought within 0.2 m (0.656 ft.) of the door outside handle assembly, communication is not possible.

    HINT:
    1. When pressing the lock switch and touching the touch sensor, hold the electrical key transmitter about 1 m (3.28 ft.) above the ground and about 0.3 m (0.984 ft.) away from the vehicle as shown in the illustration.
    2. When the key is brought near the front door outside handle assembly (for driver side), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    3. If the operation is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Entry functions operate normally.



NG
Go to step 3
OK

AFFECTED BY WAVE INTERFERENCE 

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)
  1. Disconnect the certification ECU (smart key ECU assembly) connector.



    B203512E37
  1. Disconnect the front door outside handle assembly (for driver side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    L62-3 (CLG1) - z3-6 (ANT1)
    Always
    Below 1 Ω
    L62-4 (CG1B) - z3-3 (ANT2)
    Always
    Below 1 Ω
    L62-32 (POS1) - z3-5 (B)
    Always
    Below 1 Ω
    L62-3 (CLG1) - Body ground
    Always
    10 kΩ or higher
    L62-4 (CG1B) - Body ground
    Always
    10 kΩ or higher
    L62-32 (POS1) - Body ground
    Always
    10 kΩ or higher
    z3-6 (ANT1) - Body ground
    Always
    10 kΩ or higher
    z3-3 (ANT2) - Body ground
    Always
    10 kΩ or higher
    z3-5 (B) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    L62-3 (CLG1) - z4-6 (ANT1)
    Always
    Below 1 Ω
    L62-4 (CG1B) - z4-3 (ANT2)
    Always
    Below 1 Ω
    L62-32 (POS1) - z4-5 (B)
    Always
    Below 1 Ω
    L62-3 (CLG1) - Body ground
    Always
    10 kΩ or higher
    L62-4 (CG1B) - Body ground
    Always
    10 kΩ or higher
    L62-32 (POS1) - Body ground
    Always
    10 kΩ or higher
    z4-6 (ANT1) - Body ground
    Always
    10 kΩ or higher
    z4-3 (ANT2) - Body ground
    Always
    10 kΩ or higher
    z4-5 (B) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    *2
    Front view of wire harness connector
    (to Front Door Outside Handle Assembly (for Driver Side))
    *3
    for LHD
    *4
    for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - BODY GROUND)


    B199753E31
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    z3-2 (GND) - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    z4-2 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Front Door Outside Handle Assembly (for Driver Side))
    *2
    for LHD
    *3
    for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (DOOR OSCILLATOR, LOCK/UNLOCK SENSOR SIGNAL INPUT)
  1. Reconnect the certification ECU (smart key ECU assembly) connector.



    B199753E32
  1. Measure the voltage and check for pulses according to the value(s) in the table below.

    Standard:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    z3-6 (ANT1) - z3-3 (ANT2)
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    No pulse generation
    z3-6 (ANT1) - z3-3 (ANT2)
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. All doors locked by wireless lock function
    Pulse generation
    z3-5 (B) - z3-2 (GND)
    Power switch off
    9 to 14 V
    z3-5 (B) - z3-2 (GND)
    Power switch on (IG)
    Below 2 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    z4-6 (ANT1) - z4-3 (ANT2)
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    No pulse generation
    z4-6 (ANT1) - z4-3 (ANT2)
    1. Power switch off
    2. All doors closed
    3. Key not in cabin
    4. All doors locked by wireless lock function
    Pulse generation
    z4-5 (B) - z4-2 (GND)
    Power switch off
    9 to 14 V
    z4-5 (B) - z4-2 (GND)
    Power switch on (IG)
    Below 2 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Front Door Outside Handle Assembly (for Driver Side))
    *2
    for LHD
    *3
    for RHD



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


6.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)
  1. Replace the front door outside handle assembly (for driver side) (Click here).


NEXT


7.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)
  1. Check that the entry functions operate normally (Click here).

    OK:
    Entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY WAS DEFECTIVE)