CAN COMMUNICATION SYSTEM > TERMINALS OF ECU |
| CAN NO. 1 JUNCTION CONNECTOR (for LHD) |
Check the CAN No. 1 junction connector.
Connection diagram

| *1 | Front view of wire harness connector (to CAN No. 1 Junction Connector) | *2 | to Combination Meter |
| *3 | to Steering Angle Sensor | *4 | to Main Body ECU |
| *5 | to Power Steering ECU | *6 | to DLC3 |
| *7 |
| *8 | to CAN No. 2 Junction Connector |
| *9 | to Yaw Rate Sensor | *10 | to Certification ECU |
| *11 | to Skid Control ECU | - | - |
Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| L94-1 (CANH) | P | Combination meter |
| L94-12 (CANL) | W | |
| L94-2 (CANH) | L | Steering angle sensor |
| L94-13 (CANL) | W | |
| L94-3 (CANH) | BR | Main body ECU |
| L94-14 (CANL) | W | |
| L94-4 (CANH) | R | Power steering ECU |
| L94-15 (CANL) | W | |
| L94-5 (CANH) | W | DLC3 |
| L94-16 (CANL) | Y | |
| L94-6 (CANH) | G |
|
| L94-17 (CANL) | W | |
| L94-7 (CANH) | V | CAN No. 2 junction connector |
| L94-18 (CANL) | W | |
| L94-8 (CANH) | Y | Yaw rate sensor |
| L94-19 (CANL) | L | |
| L94-9 (CANH) | BE | Certification ECU |
| L94-20 (CANL) | P | |
| L94-10 (CANH) | LG | Skid Control ECU |
| L94-21 (CANL) | L |
| CAN NO. 2 JUNCTION CONNECTOR (for LHD) |
Check the CAN No. 2 junction connector.
Connection diagram

| *1 | Front view of wire harness connector (to CAN No. 2 Junction Connector) | *2 | to CAN No. 1 Junction Connector |
| *3 | to Center Airbag Sensor Assembly | *4 | to Transmission Control ECU |
| *5 | to Power Management Control ECU | *6 | to ECM |
Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| L95-3 (CANH) | V | CAN No. 1 junction connector |
| L95-14 (CANL) | W | |
| L95-5 (CANH) | R | Center airbag sensor assembly |
| L95-16 (CANL) | G | |
| L95-7 (CANH) | Y | Transmission control ECU |
| L95-18 (CANL) | BR | |
| L95-8 (CANH) | B | Power management control ECU |
| L95-19 (CANL) | W | |
| L95-9 (CANH) | P | ECM |
| L95-20 (CANL) | V |
| CAN NO. 1 JUNCTION CONNECTOR (for RHD) |
Check the CAN No. 1 junction connector.
Connection diagram

| *1 | Front view of wire harness connector (to CAN No. 1 Junction Connector) | *2 | to Combination Meter |
| *3 | to Main Body ECU | *4 | to CAN No. 2 Junction Connector |
| *5 | to Yaw Rate Sensor | *6 | to Center Airbag Sensor Assembly |
| *7 | to Power Management Control ECU | *8 | to Transmission Control ECU |
Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| L94-1 (CANH) | P | Combination meter |
| L94-12 (CANL) | W | |
| L94-2 (CANH) | BR | Main body ECU |
| L94-13 (CANL) | W | |
| L94-3 (CANH) | V | CAN No. 2 junction connector |
| L94-14 (CANL) | W | |
| L94-4 (CANH) | Y | Yaw rate sensor |
| L94-15 (CANL) | L | |
| L94-5 (CANH) | R | Center airbag sensor assembly |
| L94-16 (CANL) | G | |
| L94-6 (CANH) | B | Power management control ECU |
| L94-17 (CANL) | W | |
| L94-7 (CANH) | Y | Transmission control ECU |
| L94-18 (CANL) | BR |
| CAN NO. 2 JUNCTION CONNECTOR (for RHD) |
Check the CAN No. 2 junction connector.
Connection diagram

| *1 | Front view of wire harness connector (to CAN No. 2 Junction Connector) | *2 | to Steering Angle Sensor |
| *3 | to Power Steering ECU | *4 | to Skid Control ECU |
| *5 | to DLC3 | *6 |
|
| *7 | to CAN No. 1 Junction Connector | *8 | to Certification ECU |
| *9 | to ECM | - | - |
Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| L95-1 (CANH) | L | Steering angle sensor |
| L95-12 (CANL) | W | |
| L95-2 (CANH) | R | Power steering ECU |
| L95-13 (CANL) | W | |
| L95-3 (CANH) | LG | Skid control ECU |
| L95-14 (CANL) | L | |
| L95-4 (CANH) | W | DLC3 |
| L95-15 (CANL) | Y | |
| L95-5 (CANH) | G |
|
| L95-16 (CANL) | W | |
| L95-6 (CANH) | V | CAN No. 1 junction connector |
| L95-17 (CANL) | W | |
| L95-7 (CANH) | BE | Certification ECU |
| L95-18 (CANL) | P | |
| L95-9 (CANH) | P | ECM |
| L95-20 (CANL) | V |
| CAN NO. 3 JUNCTION CONNECTOR |
Check the CAN No. 3 junction connector.
Connection diagram

| *1 | CAN No. 3 Junction Connector | *2 | Junction Connector B Side |
| *3 | Junction Connector A Side | *4 | Earth Terminal |
| *5 | Front view of wire harness connector (to CAN No. 3 Junction Connector) | - | - |
Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| L97-1 (CANH) | P | Power management control ECU |
| L97-2 (CANL) | V | |
| L98-1 (CANH) | LG | Seat belt control ECU |
| L98-2 (CANL) | L | |
| L99-1 (CANH) | B | Driving support ECU |
| L99-2 (CANL) | W | |
| L100-1 (CANH) | Y | Parking assist ECU |
| L100-2 (CANL) | BR |
| CAN NO. 4 JUNCTION CONNECTOR |
Check the CAN No. 4 junction connector.
Connection diagram

| *1 | Front view of wire harness connector (to CAN No. 4 Junction Connector) | *2 | to Power Management Control ECU |
| *3 | to Air Conditioning Amplifier | *4 | to Skid Control ECU |
| *5 | to ECM | - | - |
Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| L101-12 (CANH) | LG | Power management control ECU |
| L101-1 (CANL) | L | |
| L101-13 (CANH) | Y | Air conditioning amplifier |
| L101-2 (CANL) | BR | |
| L101-14 (CANH) | P | Skid control ECU |
| L101-3 (CANL) | V | |
| L101-15 (CANH) | B | ECM |
| L101-4 (CANL) | W |
| CAN NO. 5 JUNCTION CONNECTOR |
Check the CAN No. 5 junction connector.
Connection diagram

| *1 | Front view of wire harness connector (to CAN No. 5 Junction Connector) | *2 | to Millimeter Wave Radar Sensor |
| *3 | to Driving Support ECU | - | - |
Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| L102-1 (CANH) | LG | Millimeter wave radar sensor |
| L102-12 (CANL) | P | |
| L102-3 (CANH) | Y | Driving support ECU |
| L102-14 (CANL) | L |
| DLC3 |
Measure the resistance according to the value(s) in the table below.

| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L61-6 (CANH) - L61-14 (CANL) | W - Y | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L61-6 (CANH) - L61-4 (CG) | W - G | HIGH-level CAN bus line - Chassis ground | Power switch off | 200 Ω or higher |
| L61-14 (CANL) - L61-4 (CG) | Y - G | LOW-level CAN bus line - Chassis ground | Power switch off | 200 Ω or higher |
| L61-6 (CANH) - L61-16 (BAT) | W - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L61-14 (CANL) - L61-16 (BAT) | Y - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| *1 | DLC3 |
| ECM |
Disconnect the ECM connectors.

| *1 | Front view of wire harness connector (to ECM) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A57-13 (CANH) - A57-5 (CANL) | P - V | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 108 to 132 Ω |
| A57-13 (CANH) - D28-104 (E1) | P - BR | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| A57-5 (CANL) - D28-104 (E1) | V - BR | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| A57-13 (CANH) - A57-20 (BATT) | P - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A57-5 (CANL) - A57-20 (BATT) | V - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A57-12 (CANP) - A57-4 (CANN) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 108 to 132 Ω |
| A57-12 (CANP) - D28-104 (E1) | B - BR | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| A57-4 (CANN) - D28-104 (E1) | W - BR | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| A57-12 (CANP) - A57-20 (BATT) | B - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A57-4 (CANN) - A57-20 (BATT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| COMBINATION METER |
Disconnect the combination meter connector.

| *1 | Front view of wire harness connector (to Combination Meter) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L27-10 (CANH) - L27-11 (CANL) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 108 to 132 Ω |
| L27-10 (CANH) - L27-30 (ES) | P - BR | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L27-11 (CANL) - L27-30 (ES) | W - BR | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L27-10 (CANH) - L27-18 (B) | P - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L27-11 (CANL) - L27-18 (B) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| POWER MANAGEMENT CONTROL ECU |

CAN No. 1 Bus Branch Wire
![]() |
Disconnect the power management control ECU connector.
| *1 | Rear view of wire harness connector (to Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L6-25 (CA1H) - L6-24 (CA1L) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L6-25 (CA1H) - L6-5 (E02) | B - W-B | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L6-24 (CA1L) - L6-5 (E02) | W - W-B | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L6-25 (CA1H) - L6-7 (AM21) | B - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L6-24 (CA1L) - L6-7 (AM21) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CAN No. 2 Bus Main Wire
![]() |
Disconnect the power management control ECU connector.
| *1 | Rear view of wire harness connector (to Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L5-34 (CA2H) - L5-35 (CA2L) | P - V | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 108 to 132 Ω |
| L5-34 (CA2H) - L5-6 (E1) | P - BR | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L5-35 (CA2L) - L5-6 (E1) | V - BR | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L5-34 (CA2H) - L5-1 (AM22) | P - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L5-35 (CA2L) - L5-1 (AM22) | V - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
Power Management Bus Main Wire
![]() |
Disconnect the power management control ECU connector.
| *1 | Rear view of wire harness connector (to Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L6-31 (CA3P) - L6-30 (CA3N) | LG - L | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 108 to 132 Ω |
| L6-31 (CA3P) - L6-5 (E02) | LG - W-B | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L6-30 (CA3N) - L6-5 (E02) | L - W-B | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L6-31 (CA3P) - L6-7 (AM21) | LG - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L6-30 (CA3N) - L6-7 (AM21) | L - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| MAIN BODY ECU |

| *1 | Instrument Panel Junction Block and Main Body ECU (w/o LED Headlight System, w/o Remote Air Conditioning System or w/o Theft Deterrent System) | *2 | LHD |
| *3 | RHD | - | - |

| *1 | Instrument Panel Junction Block and Main Body ECU (w/ LED Headlight System, w/ Remote Air Conditioning System or w/ Theft Deterrent System) | *2 | LHD |
| *3 | RHD | - | - |
Disconnect the main body ECU connector.

| *1 | Front view of wire harness connector (to Main Body ECU) | *2 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L7-14 (CANH) - L7-13 (CANL) | BR - W | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L7-14 (CANH) - L61-4 (CG) | BR - G | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L7-13 (CANL) - L61-4 (CG) | W - G | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L7-14 (CANH) - L61-16 (BAT) | BR - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L7-13 (CANL) - L61-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER) |
![]() |
Disconnect the skid control ECU (brake booster with master cylinder) connector.
| *1 | Front view of wire harness connector (to Skid Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A58-37 (CA1H) - A58-38 (CA1L) | LG - L | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| A58-37 (CA1H) - A58-28 (GND) | LG - W | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| A58-38 (CA1L) - A58-28 (GND) | L - W | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| A58-37 (CA1H) - A58-15 (BS) | LG - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A58-38 (CA1L) - A58-15 (BS) | L - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A58-35 (CA2H) - A58-34 (CA2L) | P - V | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| A58-35 (CA2H) - A58-28 (GND) | P - W | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| A58-34 (CA2L) - A58-28 (GND) | V - W | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| A58-35 (CA2H) - A58-15 (BS) | P - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A58-34 (CA2L) - A58-15 (BS) | V - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| STEERING ANGLE SENSOR |
![]() |
Disconnect the steering angle sensor connector.
| *1 | Front view of wire harness connector (to Steering Angle Sensor) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L51-4 (CANH) - L51-3 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L51-4 (CANH) - L51-2 (ESS) | L - W-B | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L51-3 (CANL) - L51-2 (ESS) | W - W-B | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L51-4 (CANH) - L51-6 (BAT) | L - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L51-3 (CANL) - L51-6 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| YAW RATE SENSOR |
![]() |
Disconnect the yaw rate sensor connector.
| *1 | Front view of wire harness connector (to Yaw Rate Sensor) |
| *2 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L12-3 (CANH) - L12-2 (CANL) | Y - L | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L12-3 (CANH) - L12-1 (GND) | Y - W-B | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L12-2 (CANL) - L12-1 (GND) | L - W-B | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L12-3 (CANH) - L61-16 (BAT) | Y - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L12-2 (CANL) - L61-16 (BAT) | L - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| POWER STEERING ECU |
Disconnect the power steering ECU connectors.

| *1 | Front view of wire harness connector (to Power Steering ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L54-1 (CANH) - L54-7 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L54-1 (CANH) - A27-2 (PGND) | R - W-B | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L54-7 (CANL) - A27-2 (PGND) | W - W-B | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L54-1 (CANH) - A27-1 (PIG) | R - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L54-7 (CANL) - A27-1 (PIG) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| CENTER AIRBAG SENSOR ASSEMBLY |
Disconnect the center airbag sensor assembly connector.

| *1 | Front view of wire harness connector (to Center Airbag Sensor Assembly) | *2 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L16-13 (CANH) - L16-22 (CANL) | R - G | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L16-13 (CANH) - L16-25 (E1) | R - W-B | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L16-22 (CANL) - L16-25 (E1) | G - W-B | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L16-13 (CANH) - L61-16 (BAT) | R - R | CAN communication line H - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L16-22 (CANL) - L61-16 (BAT) | G - R | CAN communication line L - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| CERTIFICATION ECU (SMART KEY ECU) |
Disconnect the certification ECU connector.

| *1 | Front view of wire harness connector (to Certification ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L62-9 (CANH) - L62-10 (CANL) | BE - P | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L62-9 (CANH) - L62-15 (E) | BE - W-B | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L62-10 (CANL) - L62-15 (E) | P - W-B | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L62-9 (CANH) - L62-1 (+B) | BE - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L62-10 (CANL) - L62-1 (+B) | P - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| TRANSMISSION CONTROL ECU |

![]() |
Disconnect the transmission control ECU connectors.
| *1 | Front view of wire harness connector (to Transmission Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A24-16 (CA1H) - A24-15 (CA1L) | Y - BR | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| A24-16 (CA1H) - A24-1 (E1) | Y - BR | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| A24-15 (CA1L) - A24-1 (E1) | BR - BR | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| A24-16 (CA1H) - A23-15 (BATT) | Y - SB | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A24-15 (CA1L) - A23-15 (BATT) | BR - SB | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type) |

Disconnect the radio and display receiver assembly connectors.

| *1 | Front view of wire harness connector (to Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L149-9 (CANH) - L149-10 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L149-9 (CANH) - L146-7 (GND1) | G - BR | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L149-10 (CANL) - L146-7 (GND1) | W - BR | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L149-9 (CANH) - L146-4 (+B1) | G - SB | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L149-10 (CANL) - L146-4 (+B1) | W - SB | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| NAVIGATION ECU SUB-ASSEMBLY (for Navigation Receiver Type) |

Disconnect the navigation ECU sub-assembly connectors.

| *1 | Front view of wire harness connector (to Navigation ECU Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L130-9 (CANH) - L130-10 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L130-9 (CANH) - L127-7 (GND1) | G - BR | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L130-10 (CANL) - L127-7 (GND1) | W - BR | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L130-9 (CANH) - L127-4 (+B1) | G - SB | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L130-10 (CANL) - L127-4 (+B1) | W - SB | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| AIR CONDITIONING AMPLIFIER |
Disconnect the air conditioning amplifier connector.

| *1 | Front view of wire harness connector (to Air Conditioning Amplifier) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L17-11 (CANH) - L17-12 (CANL) | Y - BR | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L17-11 (CANH) - L17-14 (GND) | Y - W-B | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L17-12 (CANL) - L17-14 (GND) | BR - W-B | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L17-11 (CANH) - L17-21 (B) | Y - Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L17-12 (CANL) - L17-21 (B) | BR - Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| SEAT BELT CONTROL ECU (w/ Pre-crash Safety System) |

![]() |
Disconnect the seat belt control ECU connectors.
| *1 | Front view of wire harness connector (to Seat Belt Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L3-1 (CANH) - L3-2 (CANL) | LG - L | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L3-1 (CANH) - L2-8 (PGND) | LG - W-B | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L3-2 (CANL) - L2-8 (PGND) | L - W-B | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L3-1 (CANH) - L2-7 (+B) | LG - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L3-2 (CANL) - L2-7 (+B) | L - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| PARKING ASSIST ECU (w/ Intelligent Parking Assist System) |

![]() |
Disconnect the parking assist ECU connector.
| *1 | Front view of wire harness connector (to Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L151-40 (CANH) - L151-39 (CANL) | Y - BR | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L151-40 (CANH) - L152-4 (GND1) | Y - W-B | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L151-39 (CANL) - L152-4 (GND1) | BR - W-B | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L151-40 (CANH) - L152-1 (+B) | Y - SB | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L151-39 (CANL) - L152-1 (+B) | BR - SB | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| DRIVING SUPPORT ECU (w/ Dynamic Radar Cruise Control System) |
![]() |
Disconnect the driving support ECU connector.
| *1 | Front view of wire harness connector (to Driving Support ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L60-39 (CA2H) - L60-17 (CA2L) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 54 to 69 Ω |
| L60-39 (CA2H) - L60-25 (GND) | B - W-B | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L60-17 (CA2L) - L60-25 (GND) | W - W-B | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L60-39 (CA2H) - L60-30 (B) | B - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L60-17 (CA2L) - L60-30 (B) | W - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L60-40 (CA1P) - L60-18 (CA1N) | Y - L | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 108 to 132 Ω |
| L60-40 (CA1P) - L60-25 (GND) | Y - W-B | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L60-18 (CA1N) - L60-25 (GND) | L - W-B | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| L60-40 (CA1P) - L60-30 (B) | Y - B | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L60-18 (CA1N) - L60-30 (B) | L - B | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| MILLIMETER WAVE RADAR SENSOR (w/ Dynamic Radar Cruise Control System) |
![]() |
Disconnect the millimeter wave radar sensor connector.
| *1 | Front view of wire harness connector (to Millimeter Wave Radar Sensor) |
| *2 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A2-4 (CA1P) - A2-3 (CA1N) | LG - P | HIGH-level CAN bus line - LOW-level CAN bus line | Power switch off | 108 to 132 Ω |
| A2-4 (CA1P)- L61-4 (CG) | LG - G | HIGH-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| A2-3 (CA1N) - L61-4 (CG) | P - G | LOW-level CAN bus line - Ground | Power switch off | 200 Ω or higher |
| A2-4 (CA1P) - L61-16 (BAT) | LG - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A2-3 (CA1N) - L61-16 (BAT) | P - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |