Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1471/71    A/C Inverter High Voltage Power Resource System Malfunction

for Preparation Click here


DESCRIPTION

The A/C inverter assembly monitors power voltage from the main battery in the circuit. It stops compressor control and stores the DTC when the monitored voltage is outside the specified range.
The output DTC is memorized as previous trouble. Compressor control may not resume unless the power switch is turned off.

DTC No.
DTC Detection Condition
Trouble Area
B1471/71
  1. Open or short in A/C inverter high voltage power resource system.
  2. The boost pressure system is broken or malfunctioning.
  1. Electric vehicle fuse
  2. No. 2 engine wire (harness or connector between compressor with motor assembly and inverter with converter assembly)
  3. Compressor with motor assembly
  4. Hybrid control system
  5. CAN communication system

WIRING DIAGRAM


E189255E02


INSPECTION PROCEDURE

CAUTION:
  1. Wear electrically insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Be sure to carry the removed service plug grip because other workers may install it by mistake.
  2. Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.

NOTICE:
The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the flow chart for the hybrid control system first if any DTCs from those systems are output simultaneously.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Using the intelligent tester to check if the CAN communication system is functioning normally.

    Result:
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK DIAGNOSTIC TROUBLE CODE (HYBRID CONTROL SYSTEM)
  1. Check if DTCs for the hybrid control system are output using the intelligent tester.

    OK:
    Hybrid control system DTCs are not output.



NG
GO TO HYBRID CONTROL SYSTEM (Click here)
OK


3.INSPECT ELECTRIC VEHICLE FUSE

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.

  1. Remove the service plug grip.

    CAUTION:
    Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.

    NOTICE:
    Do not start the engine with the service plug grip removed because it may cause a malfunction.

  1. Remove the inverter terminal cover.

    NOTICE:
    Be sure to prevent foreign objects or water from entering the inverter with converter assembly.



    E189798E01
  1. Check that bolts A and B are tightened securely.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Item
    (Tester Connection)
    Condition
    Specified Condition
    ELECTRIC VEHICLE fuse
    (A - B)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Inverter with Converter Assembly
    *2
    Electric Vehicle Fuse



NG
REPLACE ELECTRIC VEHICLE FUSE
OK


4.INSPECT NO. 2 ENGINE WIRE

CAUTION:
Be sure to wear insulated gloves.



    E189257E02
  1. Disconnect the No. 2 engine wire connector.



    E189799E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-1 (PE) - E2-2 (ACPE)
    Always
    Below 1 Ω
    E1-2 (PB) - E2-1 (ACPB)
    Always
    Below 1 Ω
    E1-1 (PE) - Body ground
    Always
    10 kΩ or higher
    E1-2 (PB) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Compressor with Motor Assembly)
    *2
    Front view of wire harness connector
    (to Inverter with Converter Assembly)



NG
REPLACE NO. 2 ENGINE WIRE (Click here)
OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY (Click here)