Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)

ENTRY AND START SYSTEM (for Start Function) > Power Source Mode does not Change to ON (READY)

for Preparation Click here


DESCRIPTION

When the electronic key is in the cabin and the power switch is pressed, the power management control ECU receives a signal and changes the power source mode. In addition, when the power switch is pressed with park (P) selected and the brake pedal depressed, the hybrid system turns on (READY).

WIRING DIAGRAM


B231377E03


B300362E05


INSPECTION PROCEDURE

NOTICE:
  1. When the power management control ECU is replaced with a new one and the cable from the negative (-) auxiliary battery terminal is connected, the power source mode becomes on (IG) mode. When the auxiliary battery is removed and reinstalled, power source mode that was selected when the auxiliary battery was removed is restored.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HYBRID SYSTEM READY ON
  1. Place the electrical key on the driver seat.

  1. Depress the brake pedal.

  1. Check that the power switch indicator light is green. Then press the power switch to check if the hybrid system turns on (READY).

    OK:
    Power source mode becomes on (READY).



NG
Go to step 2
OK

END (HYBRID SYSTEM PERMISSION CONDITIONS WERE NOT SATISFIED) 

2.CHECK FOR DTC
  1. Turn the power switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check for DTCs.

    OK:
    DTC is not output.



NG
GO TO HYBRID CONTROL SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) (Click here)
OK


3.CHECK FOR DTC
  1. Enter the following menus: Body / Power Source Control / Data List.

  1. Check for DTCs.

    OK:
    DTC is not output.



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
OK


4.CHECK POWER SOURCE CONDITION
  1. Check the power source mode change.

    1. When the key is inside the vehicle and the park (P) is selected, check that pressing the power switch causes the power source mode to change.

      Result:
      Result
      Proceed to
      off → on (ACC) → on (IG) → off
      A
      Power source mode does not change to on (IG and ACC)
      B
      Power source mode does not change to on (IG)
      C
      Power source mode does not change to on (ACC)
      D



B
GO TO OTHER FLOW CHART (Power Source Mode does not Change to ON (IG and ACC)) (Click here)

C
GO TO OTHER FLOW CHART (Power Source Mode does not Change to ON (IG)) (Click here)

D
GO TO OTHER FLOW CHART (Power Source Mode does not Change to ON (ACC)) (Click here)
A


5.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
  1. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch1
    Stop light switch 1/ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    OK:
    ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.



NG
Go to step 11
OK


6.READ VALUE USING INTELLIGENT TESTER (L CODE)
  1. Enter the following menus: Body / Entry & Start / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    L Code Check
    L code certification result/OK or NG
    OK: L code certification result normal
    NG: L code certification result abnormal
    -

    OK:
    OK appears on the screen.



NG
Go to step 14
OK


7.READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST)
  1. Read the Data List according to the display on the intelligent tester.

    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Start Request
    Start request signal response/OK or NG
    OK: Start request condition signal received
    NG: Start request condition signal not received
    -

    OK:
    OK appears on the screen.

    Result:
    Result
    Proceed to
    OK (w/ Airbag Cut-off Switch)
    A
    OK (w/o Airbag Cut-off Switch)
    B
    NG
    C



B
Go to step 10

C
Go to step 14
A


8.READ VALUE USING INTELLIGENT TESTER (S CODE)
  1. Read the Data List according to the display on the intelligent tester.

    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    S Code Check
    S code certification result/OK or NG
    OK: S code certification result normal
    NG: S code certification result abnormal
    -

    OK:
    OK appears on the screen.



NG
Go to step 16
OK


9.CHECK ID CODE BOX (IMMOBILISER CODE ECU)


    B231391E01
  1. Measure the voltage according to the value(s) in the table below.



      B231392E01
    1. Waveform 1
      Tester Connection
      L6-20 (IMO) - L5-6 (E1)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Vehicle Condition
      Within 3 seconds after power switch on (READY), or within 3 seconds after power switch first turned on (IG) after battery disconnected and connected

    2. Waveform 2
      Tester Connection
      L6-21 (IMI) - L5-6 (E1)
      Tool Setting
      5 V/DIV., 50 ms./DIV.
      Vehicle Condition
      Power switch on (IG)

      OK:
      The waveform is displayed as shown in illustration.

      Text in Illustration 
      *1
      Component with harness connected
      (Power Management Control ECU)



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK


10.READ VALUE USING INTELLIGENT TESTER
  1. Enter the following menus: Body / Power Source Control / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Starter Request Signal
    Hybrid control system start request signal / ON or OFF
    ON: STSW signal is on
    OFF: STSW signal is off
    -

    OK:
    Data List display changes when the power switch is operated.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

GO TO HYBRID CONTROL SYSTEM (Click here)  

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)


    E233265E16
  1. Disconnect the A67 connector from the stop light switch assembly.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A67-1 (B) - A67-3 (GND)
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A67-3 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK STOP LIGHT SWITCH ASSEMBLY


    E233266E13
  1. Reconnect the A67 connector to the stop light switch assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A67-2 (L) - A67-3 (GND)
    Power switch off, brake pedal not depressed
    Below 1 V
    A67-2 (L) - A67-3 (GND)
    Power switch off, brake pedal depressed
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Stop Light Switch Assembly)



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the A22 connector from the power management control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A22-23 (STP) - A67-2 (L)
    Always
    Below 1 Ω
    A22-23 (STP)- Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

14.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY
  1. Replace transmission control ECU assembly (Click here).


NEXT


15.CHECK HYBRID SYSTEM READY ON
  1. Place the electrical key on the driver seat.

  1. Depress the brake pedal.

  1. Check that the power switch indicator light is green. Then press the power switch to check if the hybrid system turns on (READY).

    OK:
    Power source mode becomes on (READY).

    Result:
    Result
    Proceed to
    OK
    A
    NG (w/ Airbag Cut-off Switch)
    B
    NG (w/o Airbag Cut-off Switch)
    C



B
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

C
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
A

END (TRANSMISSION CONTROL ECU WAS DEFECTIVE) 

16.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace certification ECU (Entry & Start ECU assembly).


NEXT


17.CHECK HYBRID SYSTEM READY ON
  1. Place the electrical key on the driver seat.

  1. Depress the brake pedal.

  1. Check that the power switch indicator light is green. Then press the power switch to check if the hybrid system turns on (READY).

    OK:
    Power source mode becomes on (READY).



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)