Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM

DTC    C2121/21    No Signal from Transmitter ID1

DTC    C2122/22    No Signal from Transmitter ID2

DTC    C2123/23    No Signal from Transmitter ID3

DTC    C2124/24    No Signal from Transmitter ID4

DTC    C2125/25    No Signal from Transmitter ID5

DTC    C2181/81    Transmitter ID1 not Received (Test Mode DTC)

DTC    C2182/82    Transmitter ID2 not Received (Test Mode DTC)

DTC    C2183/83    Transmitter ID3 not Received (Test Mode DTC)

DTC    C2184/84    Transmitter ID4 not Received (Test Mode DTC)

DTC    C2185/85    Transmitter ID5 not Received (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressure of each wheel. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measured tire pressure values with the tire pressure threshold. When the measured tire pressure value is less than this threshold, the warning light in the combination meter assembly illuminates.
The tire pressure warning valve and transmitters constantly send radio waves to the tire pressure warning ECU and receiver.
Under the conditions below, the tire pressure warning ECU and receiver is unable to receive the signals from the tire pressure warning valve and transmitters, and a DTC is stored.
  1. Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.
  2. Devices using similar radio frequencies are used in the vehicle.
  3. The ID of a tire pressure warning valve and transmitter is mistyped during registration.
  4. A tire, wheel and/or transmitter from a different vehicle is installed.

HINT:
When no transmitter ID is received from a tire pressure warning valve and transmitter for 10 minutes or more while the vehicle speed is more than 37 km/h (23 mph), or no transmitter ID is received from all of the tire pressure warning valve and transmitters for 10 minutes or more, DTCs from C2121/21 to C2124/24 (C2125/25: w/ Full Size Spare Tire) are stored.
DTCs C2121/21 to C2124/24 (C2125/25: w/ Full Size Spare Tire) can only be cleared by using the GTS. DTCs C2181/81 to C2184/84 (C2185/85: w/ Full Size Spare Tire) can be cleared when the tire pressure warning valve and transmitter sends a forced transmission signal or test mode ends. DTCs C2181/81 to C2184/84 (C2185/85: w/ Full Size Spare Tire) are output only in test mode.


DTC No.
DTC Detection Condition
Trouble Area
C2121/21
C2122/22
C2123/23
C2124/24
C2125/25*
Following condition (a) or (b) is met:
(a) When all conditions below are met:
  1. Tire pressure warning valve and transmitter is not in stop mode.
  2. Any transmitter ID is not received from tire pressure warning valve and transmitters.
  3. Vehicle speed is more than 37 km/h (23 mph) or no vehicle speed signal is received for 10 minutes or more.
(b) When both conditions below are met:
  1. Tire pressure warning valve and transmitter is not in stop mode.
  2. No transmitter ID is received from tire pressure warning valve and transmitters for 10 minutes or more.
  1. Tire pressure warning valve and transmitter
  2. Tire pressure warning ECU and receiver
C2181/81
C2182/82
C2183/83
C2184/84
C2185/85*
Test mode procedure is performed.
  1. Tire pressure warning valve and transmitter
  2. Tire pressure warning ECU and receiver
*: w/ Full Size Spare Tire

NOTICE:
When any DTC from C2121/21 to C2124/24 (C2125/25: w/ Full Size Spare Tire) is stored, DTC C2174/74 may be stored simultaneously. In such cases, troubleshoot DTC C2174/74 first, then troubleshoot DTCs C2121/21 to C2124/24 (C2125/25: w/ Full Size Spare Tire).

HINT:
It is necessary to perform the following procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


WIRING DIAGRAM


C287864E04


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
  2. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.

1.CHECK FREQUENCY RECEIVING CONDITION
  1. Check that the following conditions are not met:

    1. Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

      HINT:
      If the vehicle is located in an area such as the one described above, the tire pressure warning light may illuminate after blinking for 1 minute due to interfering radio frequencies.

    2. Devices using similar radio frequencies are used in the vehicle.

      OK:
      Facilities or devices that use similar radio frequencies are not located in the vicinity of the vehicle.

      HINT:
      Radio wave transmissions may be interrupted due to the surroundings or devices installed by the user.



NG
CHECK IF ANY DEVICE IS INSTALLED BY USER
OK


2.IDENTIFY TRANSMITTER CORRESPONDING TO DTC
  1. Set the tire pressure to the specified value (Click here).

  1. Turn the power switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Display the "ID Tire Inflation Pressure" value for each wheel using the GTS.

  1. Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kg/cm2, 5.8 psi) within 30 seconds. If the "ID Tire Inflation Pressure" value displayed on the GTS does not change, the tire pressure warning valve and transmitter corresponding to the unchanged "ID Tire Inflation Pressure" value was the cause of the output DTC.

    HINT:
    1. Identify the malfunctioning tire pressure warning valve and transmitter by repeatedly decreasing the tire pressure for each tire.
    2. Record which "ID Tire Inflation Pressure" value corresponds to each tire.


    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID 1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 5 Tire Inflation Pressure*2
    ID5 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1

    HINT:
    1. *1: It may take a few minutes until the values are displayed.
    2. *2: w/ Full Size Spare Tire

  1. Check the Data List.

    NOTICE:
    1. It may take a few minutes until the values are displayed.
    2. When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.
    3. Record the transmitter IDs and positions of transmitters that are normal.

  1. After confirming that the "ID Tire Inflation Pressure" value for one tire has changed, repeat this procedure one by one. Identify the transmitter that corresponds to the DTC.

    Result:
    Result
    Proceed to
    One or more transmitter is abnormal
    A
    All transmitters are normal
    B



B
END
A


3.CHECK TRANSMITTER ID
  1. Turn the power switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Read the Data List according to the display on the GTS.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Registered ID 1 code
    Registered ID1 code/
    min.: 0
    max.: FFFFFFF*1
    ID No. registered for transmitter ID1 displayed
    -
    Registered ID 2 code
    Registered ID2 code/
    min.: 0
    max.: FFFFFFF*1
    ID No. registered for transmitter ID2 displayed
    -
    Registered ID 3 code
    Registered ID3 code/
    min.: 0
    max.: FFFFFFF*1
    ID No. registered for transmitter ID3 displayed
    -
    Registered ID 4 code
    Registered ID4 code/
    min.: 0
    max.: FFFFFFF*1
    ID No. registered for transmitter ID4 displayed
    -
    Registered ID 5 code*2
    Registered ID5 code/
    min.: 0
    max.: FFFFFFF*1
    ID No. registered for transmitter ID5 displayed
    -

    HINT:
    1. *1: Displayed only when the ID No. is not registered.
    2. *2: w/ Full Size Spare Tire



  1. Check the ID number on the identified transmitter by removing it from the tire and wheel.


    C239103E01


    Text in Illustration 
    *1
    Tire Pressure Warning Valve and Transmitter
    *2
    Transmitter ID (7-digit Number)

  1. Confirm that the ID number on the transmitter and recorded transmitter ID match.

    Result:
    Result
    Proceed to
    Match
    A
    Do not match
    B



B
Go to step 5
A


4.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
  1. Replace the tire pressure warning valve and transmitter (Click here).


NEXT


5.REGISTRATION OF TRANSMITTER ID
  1. Perform registration (Click here).


NEXT


6.PERFORM INITIALIZATION
  1. Perform initialization (Click here).


NEXT


7.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
  1. Turn the power switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Read the Data List according to the display on the GTS.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID 1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 5 Tire Inflation Pressure*2
    ID5 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1

    HINT:
    1. *1: It may take a few minutes until the values are displayed.
    2. *2: w/ Full Size Spare Tire
    3. When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.


    Result:

    Result
    Proceed to
    Tire pressure values are not displayed.
    A
    All tire pressure readings are equal to specified values.
    B



B
END
A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER (Click here)