Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for DVD)

NAVIGATION SYSTEM (for DVD) > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM


E255391E02


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. The vehicle is equipped with an SRS (Supplemental Restraint System). Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the navigation receiver assembly, steering pad switch assembly, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the tail or head position.

    Result:

    Result
    Proceed to
    Illumination comes on for all components except steering pad switch assembly.
    A
    Illumination comes on for all components except navigation receiver assembly.
    B
    No illumination comes on (navigation receiver assembly, steering pad switch assembly, hazard switch, glove box, etc.).
    C
    Illumination comes on for all components except navigation receiver assembly and steering pad switch assembly.
    D



B
Go to step 7

C
GO TO LIGHTING SYSTEM (Click here)

D
Go to step 8
A


2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)


    E168579E27
  1. Disconnect the L52 spiral with sensor cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L52-12 (IL+2) - Body ground
    Light control switch in tail or head
    11 to 14 V

Text in Illustration 
*1
Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY


    E187114E02
  1. Disconnect the steering pad switch assembly and spiral with sensor cable sub-assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z9-8 (EAU) - L52-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z9-5 (IL+2) - L52-12 (IL+2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

Text in Illustration 
*1
Component without harness connected
(Spiral with Sensor Cable Sub-assembly)
*2
Steering Pad Switch Assembly Side
*3
Vehicle Side


NG
REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE - NAVIGATION RECEIVER)


    E168561E39
  1. Disconnect the L41 navigation receiver assembly connector.



    E168579E28
  1. Disconnect the L52 spiral with sensor cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L41-6 (SWG) - L52-4 (EAU)
    Always
    Below 1 Ω
    L41-6 (SWG) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*1
Front view of wire harness connector
(to Navigation Receiver Assembly)
*2
Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the z9 steering pad switch assembly connector.



  1. Connect a positive (+) lead from the battery to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.


    E187367E01

  1. Check if the illumination for the steering pad switch comes on.

    OK:
    Illumination for the steering pad switch comes on.


Text in Illustration 
*1
Component without harness connected
(Steering Pad Switch Assembly)
-
-


NG
Go to step 6
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.INSPECT STEERING PAD SWITCH RH


  1. Disconnect the SR1 and z9 steering pad switch RH connectors.


    E256156E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    SR1-3 (IL+2) - z9-5 (IL+2)
    Always
    Below 1 Ω
    SR1-4 (EAU) - z9-8 (EAU)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Component without harness connected
    (Steering Pad Switch RH)
    -
    -



NG
REPLACE STEERING PAD SWITCH RH (Click here)
OK

REPLACE STEERING PAD SWITCH LH (Click here)  

7.CHECK HARNESS AND CONNECTOR (BATTERY - NAVIGATION RECEIVER ASSEMBLY)


    E187119E01
  1. Disconnect the L120 navigation receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L120-10 (ILL+) - Body ground
    Light control switch in tail or head
    11 to 14 V

Text in Illustration 
*1
Front view of wire harness connector
(to Navigation Receiver Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

8.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)


    E187119E02
  1. Disconnect the L120 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L120-7 (GND) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*1
Front view of wire harness connector
(to Navigation Receiver Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)