NAVIGATION SYSTEM (for HDD) > Steering Pad Switch Circuit |

| 1.INSPECT NAVIGATION RECEIVER ASSEMBLY |
![]() |
Disconnect the L109 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| L109-7 (SW1) - L109-6 (SWG) | No switch pushed | 95 to 105 kΩ |
| L109-7 (SW1) - L109-6 (SWG) | Seek+ switch pushed | Below 2.5 Ω |
| L109-7 (SW1) - L109-6 (SWG) | Seek- switch pushed | 323 to 335 Ω |
| L109-7 (SW1) - L109-6 (SWG) | Volume+ switch pushed | 980 to 1020 Ω |
| L109-7 (SW1) - L109-6 (SWG) | Volume- switch pushed | 3048 to 3172 Ω |
| L109-8 (SW2) - L109-6 (SWG) | No switch pushed | 95 to 105 kΩ |
| L109-8 (SW2) - L109-6 (SWG) | MODE switch pushed | Below 2.5 Ω |
| L109-8 (SW2) - L109-6 (SWG) | Voice switch pushed | 3048 to 3172 Ω |
| L109-8 (SW2) - L109-6 (SWG) | On Hook switch pushed | 323 to 335 Ω |
| L109-8 (SW2) - L109-6 (SWG) | Off Hook switch pushed | 980 to 1020 Ω |
| *1 | Front view of wire harness connector (to Navigation Receiver Assembly) |
|
| ||||
| OK | ||
| ||
| 2.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY |
![]() |
Disconnect the steering pad switch assembly and spiral with sensor cable sub-assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z9-8 (EAU) - L52-4 (EAU) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z9-10 (AU1) - L52-6 (AU1) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z9-9 (AU2) - L52-5 (AU2) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
| *1 | Component without harness connected (Spiral with Sensor Cable Sub-assembly) |
| *2 | Steering Pad Switch Assembly Side |
| *3 | Vehicle Side |
|
| ||||
| OK | |
| 3.INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the z9 steering pad switch assembly connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z9-10 (AU1) - z9-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| z9-10 (AU1) - z9-8 (EAU) | Seek+ switch pushed | Below 2.5 Ω |
| z9-10 (AU1) - z9-8 (EAU) | Seek- switch pushed | 323 to 335 Ω |
| z9-10 (AU1) - z9-8 (EAU) | Volume+ switch pushed | 980 to 1020 Ω |
| z9-10 (AU1) - z9-8 (EAU) | Volume- switch pushed | 3048 to 3172 Ω |
| z9-9 (AU2) - z9-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| z9-9 (AU2) - z9-8 (EAU) | MODE switch pushed | Below 2.5 Ω |
| z9-9 (AU2) - z9-8 (EAU) | Voice switch pushed | 3048 to 3172 Ω |
| z9-9 (AU2) - z9-8 (EAU) | On Hook switch pushed | 323 to 335 Ω |
| z9-9 (AU2) - z9-8 (EAU) | Off Hook switch pushed | 980 to 1020 Ω |
| *1 | Component without harness connected (Steering Pad Switch Assembly) | *2 | Volume+ |
| *3 | Volume- | *4 | MODE |
| *5 | Seek- | *6 | Voice Switch |
| *7 | Off Hook | *8 | Seek+ |
| *9 | On Hook | - | - |
|
| ||||
| OK | ||
| ||
| 4.INSPECT STEERING PAD SWITCH RH |
Disconnect the SR1 and z9 steering pad switch RH connectors.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| SR1-1 (AU1) - z9-10 (AU1) | Always | Below 1 Ω |
| SR1-4 (EAU) - z9-8 (EAU) | Always | Below 1 Ω |
| SR1-2 (AU2) - z9-9 (AU2) | Always | Below 1 Ω |
| *1 | Component without harness connected (Steering Pad Switch RH) | - | - |
|
| ||||
| OK | ||
| ||