FRONT DOOR > DISASSEMBLY |
| 1. REMOVE REAR NO. 2 FLOOR BOARD |
![]() |
Disengage the 2 guides <A> as shown in the illustration.
Disengage the 3 guides <B> and remove the rear No. 2 floor board.
| 2. REMOVE REAR DECK FLOOR BOX |
Remove the rear deck floor box.
| 3. REMOVE REAR NO. 3 FLOOR BOARD |
![]() |
Disengage the 2 guides and remove the rear No. 3 floor board.
| 4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug.
| 5. REMOVE ASSIST GRIP COVER |
![]() |
Using a moulding remover, disengage the 6 claws, 2 clips and 3 guides, and remove the assist grip cover.
| 6. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) |
![]() |
Disengage the 7 claws and 3 guides.
Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.
| 7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) |
![]() |
Disengage the 7 claws and 3 guides.
Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.
| 8. REMOVE DOOR ARMREST COVER |
![]() |
Remove the door armrest cover.
| 9. REMOVE COURTESY LIGHT ASSEMBLY |
![]() |
Using a moulding remover, disengage the claw.
Disconnect the connector and remove the courtesy light assembly.
| 10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Put protective tape around the front door panel.
| *1 | Protective Tape |
![]() |
Remove the 2 screws.
Using a clip remover, disengage the 9 clips.
Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.
Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.
![]() |
Disengage the 2 claws and disconnect the front door inside handle sub-assembly.
| 11. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Disconnect the front door lock remote control cable and front door inside locking cable, and remove the front door inside handle sub-assembly.
| 12. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP |
![]() |
Disengage the 7 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
| 13. REMOVE OUTER MIRROR PROTECTOR |
![]() |
Remove the screw.
Disengage the 2 claws and remove the outer mirror protector.
| 14. REMOVE OUTER MIRROR INSTALL HOLE COVER |
![]() |
Disengage the 2 claws and guide, remove the outer mirror install hole cover.
| 15. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 3 bolts.
Disengage the clip and remove the outer rear view mirror assembly.
| 16. REMOVE DOOR FRAME GARNISH |
![]() |
Disengage the clip and remove the door frame garnish.
| 17. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the connector.
Using a drill bit with a diameter of less than 4 mm (0.158 in.), drill out the 3 rivet heads and remove the front No. 1 speaker assembly.
Continue drilling and push out the remaining rivet fragments.
Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.
| 18. REMOVE FRONT DOOR TRIM BRACKET |
![]() |
Remove the 2 screws and front door trim bracket.
| 19. REMOVE FRONT DOOR SERVICE HOLE COVER |
![]() |
Remove the front door service hole cover.
| 20. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY |
![]() |
Remove the grommet.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
w/ Navigation System for HDD:
Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.
![]() |
Remove the 2 bolts.
![]() |
Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.
| 21. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY |
![]() |
Disconnect the connector.
Loosen the temporary bolt.
| *1 | Temporary Bolt |
Remove the 5 bolts.
Remove the front door window regulator assembly.
Remove the temporary bolt from the front door window regulator assembly.
| 22. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.
| 23. REMOVE FRONT DOOR STIFFENER CUSHION |
![]() |
Remove the 2 bolts and front door stiffener cushion.
| *1 | Double-sided Tape |
| 24. REMOVE FRONT DOOR GLASS RUN |
![]() |
Remove the front door glass run.
| 25. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY |
![]() |
Remove the bolt and front door rear lower frame sub-assembly as shown in the illustration.
| 26. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side) |
![]() |
Remove the hole plug.
![]() |
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.
| 27. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side) |
![]() |
Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover as shown in the illustration.
| 28. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side) |
![]() |
Remove the hole plug.
![]() |
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.
| 29. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY |
w/ entry and start system:
![]() |
Disengage the 2 claws.
Disconnect the connector.
![]() |
Move the lever in the direction indicated by the arrow in the illustration.
![]() |
Remove the front door outside handle assembly as shown in the illustration.
| 30. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD |
![]() |
Disengage the 3 claws and remove the front door front outside handle pad.
| 31. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD |
![]() |
Disengage the 2 claws and remove the front door rear outside handle pad.
| 32. REMOVE FRONT DOOR LOCK ASSEMBLY (w/o Double Locking System) |
![]() |
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the 3 screws.
Slide the front door lock assembly downward, and remove the front door lock assembly and cables as a unit.
![]() |
Remove the door lock wiring harness seal from the front door lock assembly.
| 33. REMOVE FRONT DOOR LOCK ASSEMBLY (w/ Double Locking System) |
![]() |
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the 3 screws.
Slide the front door lock assembly downward, and remove the front door lock assembly and cables as a unit.
![]() |
Remove the door lock wiring harness seal from the front door lock assembly.
| 34. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System) |
![]() |
Using a screwdriver, disengage the 7 claws as shown in the illustration.
![]() |
Remove the front door lock remote control cable assembly as shown in the illustration.
| 35. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System) |
![]() |
Using a screwdriver, disengage the 7 claws as shown in the illustration.
![]() |
Remove the front door lock remote control cable assembly as shown in the illustration.
| 36. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System) |
![]() |
Remove the front door inside locking cable assembly as shown in the illustration.
| 37. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System) |
![]() |
Remove the front door inside locking cable assembly as shown in the illustration.
| 38. REMOVE ELECTRICAL KEY WIRE HARNESS (w/ Entry and Start System) |
![]() |
Disconnect the connector.
Disengage the 4 clamps and remove the electrical key wire harness.
| 39. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
![]() |
Using a T30 "TORX" socket wrench, loosen the screw.
Slide the front door outside handle frame sub-assembly to disengage the door handle nut and claw of the front door outside handle frame sub-assembly, and then remove it.
| 40. REMOVE FRONT DOOR LOCK OPEN ROD |
![]() |
Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.
| 41. REMOVE FRONT DOOR CHECK ASSEMBLY |
![]() |
Remove the 3 bolts and front door check assembly.
| 42. REMOVE FRONT DOOR WEATHERSTRIP |
![]() |
Using a clip remover, disengage the 18 clips and remove the front door weatherstrip.
| 43. REMOVE FRONT DOOR PANEL CUSHION |
![]() |
Disengage the 2 claws and remove the 2 front door panel cushions.
| 44. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY |
![]() |
Put protective tape around the front door belt moulding assembly.
| *1 | Protective Tape |
![]() |
Using a screwdriver, disengage the 7 claws and remove the front door belt moulding assembly.
| 45. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Moulding | 20 to 30°C (68 to 86°F) |
Using a heat light, heat the front door rear window frame moulding.
![]() |
Using a moulding remover, remove the clip and front door rear window frame moulding.
| *1 | Double-sided Tape |
| 46. REMOVE NO. 1 BLACK OUT TAPE |
Using a heat light, heat the No. 1 black out tape and vehicle body.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the No. 1 black out tape to remove it.
| 47. REMOVE FRONT DOOR OUTSIDE STRIPE |
Using a heat light, heat the front door outside strip and vehicle body.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the front door outside strip to remove it.
| 48. REMOVE FRONT DOOR LOWER OUTSIDE STRIPE |
Using a heat light, heat the front door lower outside strip and vehicle body.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the front door lower outside strip to remove it.
| 49. REMOVE FRONT DOOR REAR OUTSIDE STRIPE |
Using a heat light, heat the front door rear outside strip and vehicle body.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the front door rear outside strip to remove it.