Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR

FRONT DOOR > REASSEMBLY

for Preparation Click here



1. REPAIR INSTRUCTION
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.
      Heating Temperature 
      Item
      Temperature
      Vehicle Body
      40 to 60°C (104 to 140°F)

      NOTICE:
      Do not heat the vehicle body excessively.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Installation temperature

    1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

      HINT:
      1. The most appropriate temperature for installing the tape is 25°C (77°F).
      2. When the temperature is low, the tape turns stiff and comes off easily. When the temperature is high, the tape looses elasticity.

  1. Before installation

    1. Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

      HINT:
      Spray water on the shop floor to settle any dust.

  1. Key points for handling the tape

    1. The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

      NOTICE:
      Do not bend the tape or leave it in high temperature places.



  1. Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)

    NOTICE:
    1. Position the tape accurately to achieve a neat finish and to avoid peeling.
    2. The tape cannot be reused because it deforms and will not fit any more after being removed.




    1. To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 3 to 7 cm (1.18 to 2.76 in.) per second.


      B200106E01

      NOTICE:
      Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.

      HINT:
      1. Either angle of the squeegee (pressing forward or pulling) is acceptable.
      2. Be sure to apply the tape while removing the release paper 10 to 20 mm (0.394 to 0.787 in.) from the edge of the squeegee.



  1. Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)



      B147253E01
    1. If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

      HINT:
      When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.

  1. Key points for installation of the tape (how to use a squeegee and installation procedure for corners)

    1. Remove the release paper and apply the tape carefully with your fingers.

    2. Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.

  1. Check after installation

    1. After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.

      NOTICE:
      Do not reuse the tape.



2. INSTALL NO. 1 BLACK OUT TAPE


    B229389E01
  1. Remove the portion of the No. 1 black out tape at the perforation as shown in the illustration.



  1. Refer to the illustration to position the No. 1 black out tape.


    B229390E01

    Standard Measurement 
    Dimension
    Measurement
    A
    2 to 4 mm (0.0787 to 0.157 in.)
    B
    4 to 6 mm (0.157 to 0.236 in.)

  1. Remove the release paper and apply the tape.



3. INSTALL FRONT DOOR LOWER OUTSIDE STRIPE


  1. Refer to the illustration to position the front door lower outside strip.


    B229394E01

    Standard Measurement 
    Dimension
    Measurement
    A
    2.0 mm (0.0787 in.)

  1. Remove the release paper and apply the strip.



4. INSTALL FRONT DOOR REAR OUTSIDE STRIPE


  1. Refer to the illustration to position the front door rear outside strip.


    B229396E01

    Standard Measurement 
    Dimension
    Measurement
    A
    2.0 mm (0.0787 in.)

  1. Remove the release paper and apply the strip.



5. INSTALL FRONT DOOR OUTSIDE STRIPE


  1. Refer to the illustration to position the front door outside strip.


    B229392E01

    Standard Measurement 
    Dimension
    Measurement
    A
    2.0 mm (0.0787 in.)

  1. Remove the release paper and apply the strip.



6. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:
When installing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or front door rear window frame moulding excessively.

  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



  1. Clean the front door rear window frame moulding (if reusing the front door rear window frame moulding).

    1. Using a heat light, heat the front door rear window frame moulding.

    2. Remove the double-sided tape from the front door rear window frame moulding.

    3. Wipe off any tape adhesive residue with cleaner.



    4. B229340E01
    5. Apply new double-sided tape to the front door rear window frame moulding.
      Text in Illustration 
      *1
      Double-sided Tape (A)
      *2
      Double-sided Tape (B)
      *3
      Double-sided Tape (C)
      Item
      Dimension
      A
      0.8 mm (0.0315 in.)
      B
      5.0 mm (0.197 in.)
      C
      13.0 mm (0.512 in.)
      D
      35.0 mm (1.37 in.)
      E
      420.0 mm (1.38 ft.)
      F
      410.0 mm (1.35 ft.)
      G
      1.2 mm (0.0472 in.)



    B229338E01
  1. Install the front door rear window frame moulding.
    Text in Illustration 
    *1
    Double-sided Tape

    1. Using a heat light, heat the vehicle body and front door rear window frame moulding.

    2. Remove the release paper from the face of the front door rear window frame moulding.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. Install the front door rear window frame moulding with the clip.



7. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY


    B229331
  1. Engage the 7 claws to install the front door belt moulding assembly.



8. INSTALL FRONT DOOR PANEL CUSHION


    B228780
  1. Engage the 2 claws and install 2 new front door panel cushions.



9. INSTALL FRONT DOOR WEATHERSTRIP


    B228778
  1. Engage the 18 clips and install the front door weatherstrip.



10. INSTALL FRONT DOOR CHECK ASSEMBLY
  1. Apply MP grease to the sliding areas of the front door check assembly.



    B228776E01
  1. Apply adhesive to the threads of the bolt (A).

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the front door check assembly with the 3 bolts.

    Torque:
    (A):
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }
    (B):
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



11. INSTALL FRONT DOOR LOCK OPEN ROD


    B228774E01
  1. Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.



12. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.



    B228769
  1. Engage the door handle nut and claw.

  1. Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



13. INSTALL ELECTRICAL KEY WIRE HARNESS (w/ Entry and Start System)


    B228766
  1. Engage the 4 clamps and install the electrical key wire harness.

  1. Connect the connector.



14. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)


    B228761
  1. Install the front door inside locking cable assembly as shown in the illustration.



15. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)


    B228765
  1. Install the front door inside locking cable assembly as shown in the illustration.



16. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)


    B228756
  1. Install the front door lock remote control cable assembly as shown in the illustration.



    B228749
  1. Engage the 7 claws as shown in the illustration.



17. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)


    B228759
  1. Install the front door lock remote control cable assembly as shown in the illustration.



    B228752
  1. Engage the 7 claws as shown in the illustration.



18. INSTALL FRONT DOOR LOCK ASSEMBLY (w/o Double Locking System)

NOTICE:
  1. When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock assembly.

  1. Apply MP grease to the sliding parts of the front door lock assembly.



    B228744
  1. Install a new door lock wiring harness seal to the front door lock assembly.



    B228739
  1. Insert the front door lock open rod to the front door lock assembly.

  1. Make sure that the front door lock open rod is securely connected to the front door lock assembly.

  1. Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



19. INSTALL FRONT DOOR LOCK ASSEMBLY (w/ Double Locking System)

NOTICE:
  1. When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock assembly.

  1. Apply MP grease to the sliding parts of the front door lock assembly.



    B228746
  1. Install a new door lock wiring harness seal to the front door lock assembly.



    B228743
  1. Insert the front door lock open rod to the front door lock assembly.

  1. Make sure that the front door lock open rod is securely connected to the front door lock assembly.

  1. Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



20. INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD


    B228736
  1. Engage the 2 claws and install the front door rear outside handle pad.



21. INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD


    B228734
  1. Engage the 3 claws and install the front door front outside handle pad.



22. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    B228732
  1. Insert the front end of the front door outside handle assembly into the front door outside handle frame.

  1. Insert the rear end of the front door outside handle assembly into the front door outside handle frame, then slide the front door outside handle assembly toward the front of the vehicle to install it.



    B227963
  1. Move the lever back in the direction indicated by the arrow in the illustration to lock the door outside handle assembly.



  1. w/ entry and start system:



      B228728
    1. Connect the connector.

    2. Engage the 2 claws.



23. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    B228719
  1. Engage the claw and 2 guides, and install the front door outside handle cover to the front door lock cylinder.



24. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    B228723
  1. Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    B228715
  1. Install the hole plug.



25. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    B228724
  1. Install the front door outside handle cover with lock cylinder assembly.

    HINT:
    Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.



    B228716
  1. Using a T30 "TORX" socket wrench, install the front door lock cylinder with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    B228714
  1. Install the hole plug.



26. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B228712
  1. Install the front door rear lower frame sub-assembly with the bolt as shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



27. INSTALL FRONT DOOR GLASS RUN


    B228703
  1. Install the front door glass run.



28. INSTALL FRONT DOOR STIFFENER CUSHION


  1. When reusing the front door stiffener cushion:

    1. Clean the front door stiffener cushion.

    2. Remove the double-sided tape from the front door stiffener cushion.

    3. Wipe off any tape adhesive residue with cleaner.



    4. B228709E01
    5. Apply new double-sided tape to the front door stiffener cushion as shown in the illustration.
      Area
      Dimension
      *1
      40.0 mm (1.575 in.)
      *2
      17.0 mm (0.669 in.)
      *3
      3.0 mm (0.118 in.)

  1. Clean the front door panel sub-assembly.



    B228706E01
  1. Insert the front door stiffener cushion with the 2 bolts.
    Text in Illustration 
    *1
    Double-sided Tape



29. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:
The regulator arm must be below the intermediate position when installing the power window regulator motor.



    B228701
  1. Using a T25 "TORX" socket wrench, install the front power window regulator motor assembly with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



30. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY
  1. Apply MP grease to the sliding parts of the front door window regulator assembly.

  1. Install the temporary bolt to the front door window regulator assembly.



    B228699E02
  1. Temporarily install the front door window regulator assembly.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Tighten the temporary bolt and 5 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



31. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    1. w/ Navigation System for HDD:

      NOTICE:
      After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

  1. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.



    B228695E01
  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.



    B228693
  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B228691
  1. Install the grommet.

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



32. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.



    B228689E01
  1. Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.

  1. Attach the front door service hole cover according to the reference points on the front door panel.
    Text in Illustration 
    *1
    Reference Point

    NOTICE:
    Securely install the front door service hole cover preventing wrinkles and air bubbles.



33. INSTALL FRONT DOOR TRIM BRACKET


    B228685
  1. Install the front door trim bracket with the 2 screws.



34. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY


  1. Using an air riveter or a hand riveter, install the front No. 1 speaker assembly with 4 new rivets.


    E188467E01


    Text in Illustration 
    *1
    Riveter
    *2
    Mandrel
    *a
    INCORRECT
    -
    -

    NOTICE:
    1. Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.
    2. Confirm that the rivet is seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any clearance between the rivet head and moulding.
    3. Do not leave any clearance between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.

    HINT:
    If the rivet cannot be cut, pull it once and cut it.



    E188468
  1. Connect the connector.



35. INSTALL DOOR FRAME GARNISH


    B228683
  1. Engage the clip to install a new door frame garnish.



36. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY


    B221538
  1. Engage the clip to install the outer rear view mirror assembly.

  1. Install the outer rear view mirror assembly with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



37. INSTALL OUTER MIRROR INSTALL HOLE COVER


    B221537
  1. Engage the guide and 2 claws to install the outer mirror install hole cover.



38. INSTALL OUTER MIRROR PROTECTOR


    B221534
  1. Engage the 2 claws.

  1. Install the outer mirror protector with the screw.



39. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    B228680
  1. Engage the 7 claws and install the front door inner glass weatherstrip to the front door trim board sub-assembly as shown in the illustration.



40. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B228676
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.



    B228673
  1. Engage the 2 claws and install the front door inside handle sub-assembly to the front door trim board sub-assembly.



41. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B228671
  1. Engage the 9 clips and install the front door trim board sub-assembly.

  1. Install the 2 screws.

  1. Remove the 2 pieces of protective tape.



42. INSTALL COURTESY LIGHT ASSEMBLY
  1. Connect the connector.



    E189696E01
  1. Engage the claw to install the courtesy light assembly.



43. INSTALL DOOR ARMREST COVER


    B228665
  1. Install the door armrest cover.



44. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B228663
  1. Connect the connector.

  1. Engage the 7 claws and 3 guides, and install the power window regulator master switch assembly with front door armrest base panel.



45. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
  1. Connect the connector.



    B232008
  1. Engage the 7 claws and 3 guides, and install the power window regulator switch assembly with front door armrest base panel.



46. INSTALL ASSIST GRIP COVER


    B228660
  1. Engage the 6 claws, 2 clips and 3 guides, and install the assist grip cover.



47. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B228657
  1. Engage the 3 claws and install the front door inside handle bezel plug.



48. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)


49. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



50. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



51. INSTALL REAR NO. 2 FLOOR BOARD


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.