Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Door Courtesy Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the door courtesy light switch.

WIRING DIAGRAM


E190862E02


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door Courtesy SW
    Rear door courtesy light switch RH signal/ON or OFF
    ON: Rear door LH or RH open
    OFF: Rear door LH and RH closed
    -
    RL Door Courtesy SW
    Rear door courtesy light switch LH signal/ON or OFF
    ON: Rear door LH or RH open
    OFF: Rear door LH and RH closed
    -
    Back Door Courtesy SW
    Back door courtesy switch signal/ON or OFF
    ON: Back door open
    OFF: Back door closed
    -
    FR Door Courtesy
    Front door courtesy light switch RH signal/ON or OFF
    ON: Front door RH open
    OFF: Front door RH closed
    -
    FL Door Courtesy
    Front door courtesy light switch LH signal/ON or OFF
    ON: Front door LH open
    OFF: Front door LH closed
    -

    OK:
    Normal conditions listed above are displayed.


    Result:

    Result
    Proceed to
    OK
    A
    Front door courtesy light switch LH or RH does not operate
    B
    Rear door courtesy light switch LH or RH does not operate
    C
    Back door courtesy switch does not operate
    D



B
Go to step 2

C
Go to step 5

D
Go to step 7
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)


    B203492E01
  1. Remove the front door courtesy light switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Switch body
    Pushed
    10 kΩ or higher
    1 - Switch body
    Not pushed
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front Door Courtesy Light Switch Assembly)
    *2
    Switch Body



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SWITCH)
  1. for Front LH

    1. Disconnect the 2D instrument panel junction block assembly connector.

    2. Disconnect the R6 front door courtesy light switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2D-35 - R6-1
      Always
      Below 1 Ω
      2D-35 - Body ground
      Always
      10 kΩ or higher

  1. for Front RH

    1. Disconnect the 2D instrument panel junction block assembly connector.

    2. Disconnect the S5 front door courtesy light switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2D-36 - S5-1
      Always
      Below 1 Ω
      2D-36 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    E182468E03
  1. for Front LH

    1. Remove the instrument panel junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2D-35 - A-2 (FLCY)
      Always
      Below 1 Ω
      2D-35 - Body ground
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Component without harness connected
      (Instrument Panel Junction Block Assembly)



    E182468E04
  1. for Front RH

    1. Remove the instrument panel junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2D-36 - A-4 (FRCY)
      Always
      Below 1 Ω
      2D-36 - Body ground
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Component without harness connected
      (Instrument Panel Junction Block Assembly)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

5.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)


    B203492E01
  1. Remove the rear door courtesy light switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Switch body
    Pushed
    10 kΩ or higher
    1 - Switch body
    Not pushed
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Rear Door Courtesy Light Switch Assembly)
    *2
    Switch Body



NG
REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR COURTESY LIGHT SWITCH)
  1. for Rear LH

    1. Disconnect the L7 main body ECU (multiplex network body ECU) connector.

    2. Disconnect the R13 rear door courtesy light switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L7-6 (LRCY) - R13-1
      Always
      Below 1 Ω
      L7-6 (LRCY) - Body ground
      Always
      10 kΩ or higher

  1. for Rear RH

    1. Disconnect the L7 main body ECU (multiplex network body ECU) connector.

    2. Disconnect the S10 rear door courtesy light switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L7-6 (LRCY) - S10-1
      Always
      Below 1 Ω
      L7-6 (LRCY) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

7.INSPECT BACK DOOR LOCK ASSEMBLY


    B228545E02
  1. Remove the back door lock assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (E) - 2 (+)
    Locked
    10 kΩ or higher
    1 (E) - 2 (+)
    Unlocked
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Back Door Lock Assembly)
    *2
    Lock
    *3
    Unlock



NG
REPLACE BACK DOOR LOCK ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - MAIN BODY ECU)
  1. Disconnect the L7 main body ECU (multiplex network body ECU) connector.

  1. Disconnect the R18 back door lock assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L7-19 (BCTY) - R18-2 (+)
    Always
    Below 1 Ω
    L7-19 (BCTY) - Body ground
    Always
    10 kΩ or higher
    R18-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)