Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY

FRONT SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    B221493E01
  1. Engage the guide to temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.

  1. Fully tighten the bolt <A> first, then the bolt <B> to install the front shoulder belt anchor adjuster assembly.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY


    B221492E01
  1. Temporarily install the front seat outer belt assembly with the 2 bolts.

  1. Fully tighten the bolt <A> first, then the bolt <B> to install the front seat outer belt assembly.

    Torque:
    Bolt <A>:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }
    Bolt <B>:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B221521
  1. Connect the connector and lock the locking button as shown in the illustration.

    NOTICE:
    Securely lock the locking button.

  1. Connect each connector.



    B221491
  1. Connect the shoulder anchor of the front seat outer belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL CENTER PILLAR GARNISH
  1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH.



    B227786
  1. Engage the clip.

  1. Install the center pillar garnish LH with the screw.



4. INSTALL CENTER PILLAR LOWER GARNISH


    B227782
  1. Engage the 2 claws and 2 clips to install the center pillar lower garnish LH.



5. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B227772E01
  1. Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
    Text in Illustration 
    *1
    Alignment Mark (Red)

    NOTICE:
    After installation, check that the corners fit correctly.



6. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B227774E01
  1. Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *1
    Alignment Mark (Yellow)

    NOTICE:
    After installation, check that the corners fit correctly.



7. CONNECT FRONT SEAT OUTER BELT ASSEMBLY


    B221489
  1. Install the floor end of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.



8. INSTALL LAP BELT OUTER ANCHOR COVER


    B221487
  1. Engage the 3 claws to install the lap belt outer anchor cover.



9. INSTALL REAR DOOR SCUFF PLATE


    B227766
  1. Engage the 7 claws to install the rear door scuff plate LH.



10. INSTALL FRONT DOOR SCUFF PLATE


    B227761
  1. Engage the 10 claws to install the front door scuff plate LH.



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



12. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



13. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



14. INSTALL REAR NO. 2 FLOOR BOARD


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.



15. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).