AUDIO AND VISUAL SYSTEM > Illumination Circuit |
| w/o PANEL Relay |

| w/ PANEL Relay |

| 1.CHECK ILLUMINATION |
Check if the illumination for the radio receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, etc.) comes on when the light control switch is turned to the head or tail position.
| Result | Proceed to |
| Illumination comes on for all components except steering pad switch assembly. | A |
| Illumination comes on for all components except radio receiver assembly. | B |
| No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.). | C |
| Illumination comes on only for steering pad switch assembly. | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY) |
![]() |
Disconnect the spiral with sensor cable sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L52-12 (IL+2) - Body ground | Light control switch tail or head | 11 to 14 V |
| *1 | Front view of wire harness connector (to Spiral with Sensor Cable Sub-assembly) |
|
| ||||
| OK | |
| 3.INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch assembly connector.
Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.

Check if the illumination for the steering pad switch assembly comes on.
| *1 | Component without harness connected (Steering Pad Switch Assembly) | - | - |
Proceed to the next step based on the inspection result.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 4.INSPECT STEERING PAD SWITCH RH |
Disconnect the steering pad switch RH connectors.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| SR1-3 (IL+2) - z9-5 (IL+2) | Always | Below 1 Ω |
| SR1-4 (EAU) - z9-8 (EAU) | Always | Below 1 Ω |
| *a | Component without harness connected (Steering Pad Switch RH) | - | - |
|
| ||||
| OK | ||
| ||
| 5.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY |
![]() |
Disconnect the steering pad switch assembly and spiral with sensor cable sub-assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z9-8 (EAU) - L52-4 (EAU) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z9-5 (IL+2) - L52-12 (IL+2) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
| *1 | Component without harness connected (Spiral with Sensor Cable Sub-assembly) |
| *2 | Steering Pad Switch Assembly Side |
| *3 | Vehicle Side |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR |
![]() |
Disconnect the radio receiver assembly and spiral with sensor cable sub-assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L50-6 (SWG) - L52-4 (EAU) | Always | Below 1 Ω |
| L50-6 (SWG) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Radio Receiver Assembly) |
| *2 | Front view of wire harness connector (to Spiral with Sensor Cable Sub-assembly) |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER ASSEMBLY) |
![]() |
Disconnect the radio receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L34-10 (ILL+) - Body ground | Light control switch tail or head | 11 to 14 V |
| *1 | Front view of wire harness connector (to Radio Receiver Assembly) |
|
| ||||
| OK | |
| 8.INSPECT RADIO RECEIVER ASSEMBLY |
![]() |
Disconnect the radio receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L34-7 (GND) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Radio Receiver Assembly) |
|
| ||||
| OK | ||
| ||