Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for DVD)

NAVIGATION SYSTEM (for DVD) > Speaker Circuit

for Preparation Click here


DESCRIPTION

The sound signals amplified by the stereo component amplifier assembly are sent to the speakers from the stereo component amplifier assembly via the speaker circuit.
If there is a short in this circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.
If a short is detected in the speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM


E187101E01


E187102E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR


    E187119E03
  1. Disconnect the L120 navigation receiver assembly connector.



    E187120E01
  1. Disconnect the L121 navigation receiver assembly connector.



    E187121E01
  1. Disconnect the L108 stereo component amplifier assembly connector.



    E176481E09
  1. Disconnect the O1 and N1 front No. 1 speaker connectors.



    E187204E01
  1. Disconnect the I5 and I4 front No. 2 speaker connectors.



    E176481E10
  1. Disconnect the Q3 and P3 rear speaker connectors.



    E187133E01
  1. Disconnect the Q5 and P5 rear No. 2 speaker connectors.

  1. Measure the resistance between each of the navigation receiver assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L120-2 (FL+) - L108-1 (RL+)
    Always
    Below 1 Ω
    L120-6 (FL-) - L108-6 (RL-)
    Always
    Below 1 Ω
    L120-1 (FR+) - L108-2 (RR+)
    Always
    Below 1 Ω
    L120-5 (FR-) - L108-7 (RR-)
    Always
    Below 1 Ω
    L120-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    L120-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    L120-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    L120-6 (FL-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the front No. 1 speakers and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L108-4 (WFL+) - O1-1
    Always
    Below 1 Ω
    L108-11 (WFL-) - O1-2
    Always
    Below 1 Ω
    L108-3 (WFR+) - N1-1
    Always
    Below 1 Ω
    L108-8 (WFR-) - N1-2
    Always
    Below 1 Ω
    L108-4 (WFL+) - Body ground
    Always
    10 kΩ or higher
    L108-11 (WFL-) - Body ground
    Always
    10 kΩ or higher
    L108-3 (WFR+) - Body ground
    Always
    10 kΩ or higher
    L108-8 (WFR-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the front No. 2 speakers and the navigation receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L120-2 (FL+) - I5-1
    Always
    Below 1 Ω
    L120-6 (FL-) - I5-2
    Always
    Below 1 Ω
    L120-1 (FR+) - I4-1
    Always
    Below 1 Ω
    L120-5 (FR-) - I4-2
    Always
    Below 1 Ω
    L120-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    L120-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    L120-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    L120-5 (FR-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the rear No. 2 speakers and the navigation receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L121-2 (RL+) - Q5-1 (+)
    Always
    Below 1 Ω
    L121-6 (RL-) - Q5-2 (-)
    Always
    Below 1 Ω
    L121-1 (RR+) - P5-1 (+)
    Always
    Below 1 Ω
    L121-3 (RR-) - P5-2 (-)
    Always
    Below 1 Ω
    L121-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    L121-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    L121-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    L121-3 (RR-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the rear No. 2 speakers and the rear speakers to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q5-3 (+) - Q3-1
    Always
    Below 1 Ω
    Q5-4 (-) - Q3-2
    Always
    Below 1 Ω
    P5-3 (+) - P3-1
    Always
    Below 1 Ω
    P5-4 (-) - P3-2
    Always
    Below 1 Ω
    Q5-3 (+) - Body ground
    Always
    10 kΩ or higher
    Q5-4 (-) - Body ground
    Always
    10 kΩ or higher
    P5-3 (+) - Body ground
    Always
    10 kΩ or higher
    P5-4 (-) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*1
Front view of wire harness connector
(to Navigation Receiver Assembly)
*2
Front view of wire harness connector
(to Stereo Component Amplifier Assembly)
*3
Front view of wire harness connector
(to Front No. 1 Speaker)
*4
Front view of wire harness connector
(to Front No. 2 Speaker)
*5
Front view of wire harness connector
(to Rear Speaker)
*6
Front view of wire harness connector
(to Rear No. 2 Speaker)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER


    E165683E38
  1. Resistance check

    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O1-1 - O1-2
      Always
      1.6 to 2.4 Ω
      N1-1 - N1-2
      Always
      1.6 to 2.4 Ω

      NOTICE:
      The speaker should not be removed to check resistance.

Text in Illustration 
*1
Component without harness connected
(Front No. 1 Speaker)


NG
REPLACE FRONT NO. 1 SPEAKER (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER


    E187205E01
  1. Resistance check

    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I5-1 - I5-2
      Always
      6.4 to 9.6 Ω
      I4-1 - I4-2
      Always
      6.4 to 9.6 Ω

      NOTICE:
      The speaker should not be removed to check resistance.

Text in Illustration 
*1
Component without harness connected
(Front No. 2 Speaker)


NG
REPLACE FRONT NO. 2 SPEAKER (Click here)
OK


4.INSPECT REAR SPEAKER


    E165683E39
  1. Resistance check

    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Q3-1 - Q3-2
      Always
      3.2 to 4.8 Ω
      P3-1 - P3-2
      Always
      3.2 to 4.8 Ω

      NOTICE:
      The speaker should not be removed to check resistance.

Text in Illustration 
*1
Component without harness connected
(Rear Speaker)


NG
REPLACE REAR SPEAKER (Click here)
OK


5.INSPECT REAR NO. 2 SPEAKER
  1. Check that the malfunction disappears when another speaker in good condition is installed.

    Standard:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the rear No. 2 speakers that were disconnected.
    2. If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

END (REAR NO. 2 SPEAKER WAS DEFECTIVE)