Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Radio Broadcast cannot be Received or Poor Reception

for Preparation Click here


INSPECTION PROCEDURE

1.CHECK RADIO RECEIVER ASSEMBLY
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.

      Result:

      Result
      Proceed to
      Automatic station search function stops on a station
      A
      Automatic station search function does not stop
      B



B
Go to step 2
A

REPLACE RADIO RECEIVER ASSEMBLY (Click here)  

2.CHECK OPTIONAL COMPONENTS
  1. Check optional components (sunshade film, telephone antenna, etc.).

    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      Result:

      Result
      Proceed to
      Optional components are installed
      A
      Optional components are not installed
      B

      NOTICE:
      Do not remove any optional components installed by the customer without his or her consent.



B
Go to step 3
A

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE) 

3.CHECK RADIO ANTENNA
  1. Preparation for check

    1. Remove the roof antenna pole sub-assembly from the amplifier antenna assembly.

  1. Check for noise

    1. Turn the power switch on (ACC) with the radio receiver assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire, or other metal object on the amplifier antenna threaded installation portion for the roof antenna pole sub-assembly and check that noise can be heard from the speakers.

      Result:
      Result
      Proceed to
      Noise does not occur
      A
      Noise occurs
      B



B
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
A


4.CONFIRM MODEL
  1. Check the type of connection between the antenna cord and radio receiver assembly.

    Result:

    Result
    Proceed to
    for Plug Type Antenna Cord
    A
    for Connector Type Antenna Cord
    B



B
Go to step 9
A


5.CHECK RADIO RECEIVER ASSEMBLY


    E050367
  1. Preparation for check

    1. Remove the antenna plug from the radio receiver assembly.

  1. Check for noise

    1. Turn the power switch on (ACC) with the radio receiver assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

      OK:
      Noise can be heard from the speaker.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - AMPLIFIER ANTENNA ASSEMBLY)


    E191447E01
  1. Disconnect the radio receiver assembly and amplifier antenna assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L34-8 (ANT) - L36-2 (B)
    Always
    Below 1 Ω
    L34-8 (ANT) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio Receiver Assembly)
    *2
    Front view of wire harness connector
    (to Amplifier Antenna Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT RADIO RECEIVER ASSEMBLY


    E187221E03
  1. Reconnect the radio receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L36-2 (B) - Body ground
    Power switch on (IG)
    Radio switch on
    8 V or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Amplifier Antenna Assembly)



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


8.CHECK ANTENNA CORD
  1. Remove the antenna plug of the radio receiver assembly and antenna.

  1. Measure the resistance between the antenna and radio receiver assembly to check for an open circuit in the antenna cord.

    Standard Resistance:
    Below 1 Ω

  1. Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.

    Standard Resistance:
    10 kΩ or higher

    Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 12
A

REPLACE ANTENNA CORD (Click here)  

9.CHECK RADIO RECEIVER ASSEMBLY


    E187251
  1. Preparation for check

    1. Remove the antenna connector from the radio receiver assembly.

  1. Check for noise

    1. Turn the power switch on (ACC) with the radio receiver assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

      OK:
      Noise can be heard from the speaker.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


10.INSPECT RADIO RECEIVER ASSEMBLY


    E188455E03
  1. Disconnect the radio receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    RA-5 (ANT+) - Body ground
    Power switch on (ACC)
    Radio switch on
    8 V or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Radio Receiver Assembly)



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


11.CHECK ANTENNA CORD
  1. Remove the antenna connector of the radio receiver assembly and antenna.

  1. Measure the resistance between the antenna and radio receiver assembly to check for an open circuit in the antenna cord.

    Standard Resistance:
    Below 1 Ω

  1. Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.

    Standard Resistance:
    10 kΩ or higher



NG
REPLACE ANTENNA CORD (Click here)
OK


12.REPLACE AMPLIFIER ANTENNA ASSEMBLY
  1. Replace the amplifier antenna assembly and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK

NORMAL OPERATION