Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

NAVIGATION SYSTEM (for Navigation Receiver Type) > Radio Broadcast cannot be Received or Poor Reception

for Preparation Click here


INSPECTION PROCEDURE

1.CHECK NAVIGATION ECU SUB-ASSEMBLY
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.

      Result:
      Result
      Proceed to
      Automatic station search function does not stop
      A
      Automatic station search function stops on a station
      B



B
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)
A


2.CHECK OPTIONAL COMPONENTS
  1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

    Result:
    Result
    Proceed to
    Optional components are not installed
    A
    Optional components are installed
    B

    NOTICE:
    Do not remove optional components without the permission of the customer.



B
REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)
A


3.CHECK RADIO ANTENNA
  1. Preparation for check

    1. Remove the roof antenna pole sub-assembly from the amplifier antenna assembly (for Roof).

  1. Check for noise

    1. Turn the power switch on (ACC) with the navigation ECU sub-assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire, or other metal object on the amplifier antenna threaded installation portion for the roof antenna pole sub-assembly and check that noise can be heard from the speakers.

      Result:
      Result
      Proceed to
      Noise does not occur
      A
      Noise occurs
      B



B
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)
A


4.CHECK NAVIGATION ECU SUB-ASSEMBLY


    E187251
  1. Preparation for check

    1. Remove the antenna connector from the navigation ECU sub-assembly.

  1. Check for noise

    1. Turn the power switch on (ACC) with the navigation ECU sub-assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire or other metal object on the navigation ECU sub-assembly antenna jack and check that noise can be heard from the speakers.

      OK:
      Noise can be heard from the speakers.



NG
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)
OK


5.INSPECT NAVIGATION ECU SUB-ASSEMBLY
  1. Disconnect the navigation ECU sub-assembly connector.



    E188455E19
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    RA-5 (ANT+) - Body ground
    Power switch on (ACC)
    Radio switch on and AM or FM selected
    11 to 14 V

    Text in Illustration 
    *a
    Component without harness connected
    (Navigation ECU Sub-assembly)



NG
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)
OK


6.REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
  1. Replace the No. 2 antenna cord sub-assembly and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received normally.



NG
Go to step 7
OK

NORMAL OPERATION 

7.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY
  1. Disconnect the No. 4 antenna cord sub-assembly.

  1. Measure the resistance of the No. 4 antenna cord sub-assembly to check for an open circuit in the No. 4 antenna cord sub-assembly.

    Standard Resistance:
    Below 1 Ω

  1. Measure the resistance between the No. 4 antenna cord sub-assembly and body ground to check for a short circuit in the No. 4 antenna cord sub-assembly.

    Standard Resistance:
    10 kΩ or higher



NG
REPLACE NO. 4 ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


8.INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY
  1. Disconnect the No. 5 antenna cord sub-assembly.

  1. Measure the resistance of the No. 5 antenna cord sub-assembly to check for an open circuit in the No. 5 antenna cord sub-assembly.

    Standard Resistance:
    Below 1 Ω

  1. Measure the resistance between the No. 5 antenna cord sub-assembly and body ground to check for a short circuit in the No. 5 antenna cord sub-assembly.

    Standard Resistance:
    10 kΩ or higher



NG
REPLACE NO. 5 ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


9.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
  1. Check that the roof antenna pole sub-assembly is securely installed (Click here).

    OK:
    The roof antenna pole sub-assembly is installed properly.



NG
CHECK AND REPLACE ROOF ANTENNA POLE SUB-ASSEMBLY (Click here)
OK


10.REPLACE AMPLIFIER ANTENNA ASSEMBLY (for Roof)
  1. Replace the amplifier antenna assembly (for Roof) and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received normally.



NG
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)
OK

NORMAL OPERATION